Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man4) Handy Guide ▷ View online
Initial Setup
SHARP
Document Solution Centre
9
PRINT IMAGE POSITION & MAGNIFICATION
Automatic Adjustment:-
Sim 50-28
BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
Manual Adjustment:-
Sim
50-10
BK MAG (inside dimension) to 240mm.
Sim
50-10
Image Off Centre Adjustment.
Sim 50-05
Printer Lead Edge & Void Adjust.
IMAGE SKEW & COLOUR REGISTRATION
Sim 61-04
Image Skew Adjustment (Black)
Select A3 Paper.
Sim 50-22
Colour Registration/Skew & OPC Drum Phase Adjustment
Check/Adjust SKEW (CMY) so value is Close to 0 as possible
(Result=OK).
HALF TONE COLOUR CALIBRATION
Sim
46-74 Engine & Printer Colour Calibration
Select FACTORY Mode.
COPY IMAGE QUALITY
Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-01
Copy Density Adjust. (Colour).
Sim 46-02
Copy Density Adjust. (B/W).
Sim 46-09
SPF Copy Density Adjust.
Sim
50-28
OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc).:
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim
50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim
50-12
OC & SPF Off Centre Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode) – Density.
Sim 64-05
PCL Density Test Page
Sim 64-06
PS Density Test Page
Initial Setup
10
SHARP
Document Solution Centre
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX-FX11
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Fax Memory Clear (For Extended Memory).
Sim 66-39
Fax Destination Set.
FINISHER OPTION – MX-FNX9, MX-FN10, MX-FN11, MX-FN18
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN10/18 only]
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode
(ON/OFF).
EXTERNAL KEYBOARD – MX-KB11N
Keyboard Language Setting:
System Settings – Default Settings – Keyboard Select:
Select English(US).
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
USB Card Reader detection control:-
SSW 6-8
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print.
Device Clone & Storage Backup.
Sim 56-01
Backup EEPROM Data to HDD.
Colour Calibration
SHARP
Document Solution Centre
11
Automatic Colour Calibration - FACTORY MODE
Note: When adjusting colour balance before or after routine maintenance, always use the
recommended paper (Mondi 90gsm or equivalent) for optimum image quality.
DEFAULT COLOUR BALANCE SETTING:
Sim
63-11 [for Engine]
Sim
67-26 [for Printer]
Def 1 Standard Colour Balance setting (Default).
Def 2 Colour balance with slightly strong cyan.
Def 3 Colour balance with the emphasis on Cyan.
COLOUR BALANCE ADJUSTMENT:
Sim
46-74 [Engine & Printer]
FACTORY MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
Manual Colour Calibration – SERVICE MODE
HIGH DENSITY PROCESS CONTROL:
[Execute]
Sim
44-06
COLOUR BALANCE ADJUSTMENT:
Sim
46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
MANUAL COLOUR DENSITY ADJUSTMENT:
Sim
46-21 [for Engine]
Sim
67-25 [for Printer]
Adjust CMYK (17 points) for Copy & Printer Modes.
Colour Calibration
12
SHARP
Document Solution Centre
PRINTER DENSITY CHECK:
Sim
64-05 [PCL Printer]
Sim
64-06 [PS Printer]
SERVICE COLOUR TARGET SETTING:
Sim
63-07 [for Engine]
Sim
67-27 [for Printer]
Scan Test Pattern to Register Custom Service Target
DEFAULT SETTING (Service Mode):
To return machine to “Standard” setting:-
STANDARD SERVICE TARGET SETTING:
[Execute]
Sim
63-08 [for Engine]
Sim
67-28 [for Printer]
COLOUR BALANCE ADJUSTMENT:
Sim
46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man4) service manuals if exist.