Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N MX-FX11 (FACSIMILE EXPANSION KIT) 20 – 2
C. Attach the interface cable.
1)
Connect the interface cable to the control PWB unit.
[Note] Check that the connector is not obliquely inserted.
[Note] Check that the connector is not obliquely inserted.
2)
Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
metal on the control PWB unit.
3)
Fix a snap band with the M3 screw (Packed items).
D. Attach the control PWB and the right rear
cabinet
1)
Push the control PWB unit into the main unit and secure it with
the two screws.
the two screws.
2)
Cut out the cut-out portion of the right rear cabinet.
3)
Fit the interface cable into the opening that has been cut.
4)
Attach the right rear cabinet cover to the main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
5)
Secure the right rear cabinet with the screw.
6)
Attach the ozone filter cover to the main unit.
E. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
F. Destination setting
1)
Enter the SIM26-6 mode.
2)
Check to confirm that the destination setting of the machine
matches the specifications of the FAX destination. If not, the
FAX may not function properly.
matches the specifications of the FAX destination. If not, the
FAX may not function properly.
G. Clear theFAX related software swithes
1)
Enter the SIM66-2 mode.
2)
Press DEST CODE button.
3)
Take a note of the corresponding destination code.
4)
Press BACK button to return to the code entry mode.
5)
Enter the destination code taken in procedure 3), and press
SET button.
SET button.
6)
Press EXECUTE and YES buttons.
Hook 1 Hook 2
Hook 3
Hook 4
3
5
4
MX-5111N MX-FX11 (FACSIMILE EXPANSION KIT) 20 – 3
H. Line cable connection
1)
Connect the line cable (Packed items) on the line to the modu-
lar jack indicated as “LINE.”
lar jack indicated as “LINE.”
MEMO: When connecting the line cable (to LINE or TEL), wind the
line cable two turns around the ferrite core (Packed items) as
shown in the figure, and connect to the modular jack which is
marked with “LINE.”
line cable two turns around the ferrite core (Packed items) as
shown in the figure, and connect to the modular jack which is
marked with “LINE.”
MEMO: After connection, perform the setting of “External tele-
phone connection" of the system setting (administrator).
phone connection" of the system setting (administrator).
About
10 cm
10 cm
MX-5111N AR-SU1 (STAMP UNIT) 21 – 1
MX-5111N
Service Manual
[21] AR-SU1 (STAMP UNIT)
1. Unpacking
A. Remove the stamp unit
B. Packed items check
* When replacing the stamp cartridge, Refer to “Stamp cartridge
replacement” in the “User’s Guide” (PDF document) which is
stored in the hard disk of the machine. The user must be notified
of that. (Do not refer to “Stamp cartridge replacement procedure”
(Packed items).)
stored in the hard disk of the machine. The user must be notified
of that. (Do not refer to “Stamp cartridge replacement procedure”
(Packed items).)
2. Installation (RSPF model)
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Install the stamp unit
1)
Open the RSPF unit, and remove the OC mat.
For removing and fixing screws, use a stubby screwdriver.
For removing and fixing screws, use a stubby screwdriver.
* If stubby screwdriver is not available, loosen the screw of
the angle adjustment plate on the rear side of the machine,
and lower the angle adjustment plate and put the RSPF unit
straight.
and lower the angle adjustment plate and put the RSPF unit
straight.
2)
Remove the sensor cover. Remove the stamp case, and
remove the earth cord.
remove the earth cord.
No.
Name
Quantity
1
Stamp unit
1
2
Stamp cartridge replacement procedure*
1
3
Stamp cartridge
3
4
Installing screw
1
1
2
3
4
MX-5111N AR-SU1 (STAMP UNIT) 21 – 2
3)
Attach the stamp unit (Packed items) to the stamp case which
was removed from the RSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
was removed from the RSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
4)
Install the stamp case unit, and connect the connector.
5)
Install the sensor cover.
6)
Install the stamp cartridge (Packed items).
7)
Install the OC mat, and close the RSPF unit.
* If the angle adjustment plate was lowered for installation, lift
the angle adjustment plate, and fix it with the screw, and
close the RSPF unit.
close the RSPF unit.
B. Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.