Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) Service Manual ▷ View online
MX-5111N MX-FN18 (SADDLE STITCH FINISHER) 15 – 5
6)
Remove the screws, and remove the paper pass latch recep-
tion parts and the positioning pin.
tion parts and the positioning pin.
C. Attaching the mylar
1)
Attach the mylar (Packed items) to the position indicated in the
figure.
figure.
D. Attach the interface left cabinet
1)
Insert the rib of the interface left cabinet into the slit on the
lower surface of the scanner left cabinet. Install the interface
left cabinet with the screw of the paper exit tray which was
removed in procedure 4).
lower surface of the scanner left cabinet. Install the interface
left cabinet with the screw of the paper exit tray which was
removed in procedure 4).
E. Installation of the connection fixture F/R
1)
Install the connection fixture R (Packed items (No.8)) to the
main unit with the fixing screws (Packed items (No.3)).
main unit with the fixing screws (Packed items (No.3)).
2)
Install the connection fixture F (Packed items (No.7)) to the
main unit with the fixing screws (Packed items (No.3)).
main unit with the fixing screws (Packed items (No.3)).
F. Attaching the cushion
1)
Attach the cushion (S) (Packed items), the cushion (M)
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
Corner reference
Reference
Reference
Corner
reference
reference
Cushion (M)
Refer-
ence
Reference
Cushion (L)
Cushion (S)
Reference
Refer-
ence
Reference
Refer-
ence
MX-5111N MX-FN18 (SADDLE STITCH FINISHER) 15 – 6
G. Check of the connected position of main unit
and finisher
1)
Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.
sheet metal of the main unit, install the finisher.
2)
Remove the screw, and remove the connector cover on rear
side of the finisher.
side of the finisher.
3)
Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
* When not the range of specification, execute the following
adjustment. If the adjustment is not required, Progress to the
procedure of "I. Connection of the saddle stitch finisher".
procedure of "I. Connection of the saddle stitch finisher".
H. Adjustment
1)
Remove the finisher from the main unit.
2)
Open the front door.
3)
Remove the cabinet fixing screw.
1
: '11/Jul/25
1
MX-5111N MX-FN18 (SADDLE STITCH FINISHER) 15 – 7
4)
Remove the screw, and remove the front lower cabinet 1.
Remove the fixing screw of the front lower cabinet 2.
Remove the fixing screw of the front lower cabinet 2.
5)
Remove the screws, and slide to the left the front lower cabinet
2, and remove it.
2, and remove it.
6)
Remove the fixing tapes.
7)
Remove the screws, and remove the rear lower cover.
8)
Remove the fixing tapes.
9)
Loosen the caster fixing screws.
10) Remove the screw, and remove the spanner installed inside
the front door.
MX-5111N MX-FN18 (SADDLE STITCH FINISHER) 15 – 8
11) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
12) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
13) Tighten the caster fixing screws so that the indicator scale is
fit.
14) Install the rear lower cover with the fixing screws.
15) Install the front lower cabinet 2 with the fixing screws.
16) Install the front lower cabinet 1 with the fixing screws.
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man12) service manuals if exist.