Sharp MX-2630 Service Manual ▷ View online
MX-2630N MX-RB25 N (PAPER PASS UNIT) 9 – 5
16) Affix base resting cushion on back side of reverse gate tray.
17) Attach the reverse gate tray (Packed item No.6)
18) Remove the connector cover of the rear side of the main unit.
19) Cut the section where the harness gets through with the nipper.
20) Secure the harness of the interface unit with the screw (Packed
items No.3 x1), and connect the connector.
21) Remove two screws of the rear cabinet of the main unit and attach
the step screw at one place.
0mm
2.0mm
2.0mm
0mm
Reference position
(Hole edge face)
Reference position (Hole edge face)
Ĭ
Remove two screws
MX-2630N MX-RB25 N (PAPER PASS UNIT) 9 – 6
22) Fix it with the screw.
23) Insert the harness fixing plate to the groove of main unit and fix
the harness fixing plate with the screw B (Packed items No.3).
24) Connect the connector to the PWB.
25) Pass the harness of the relay unit through the wire saddle.
26) Secure the connector cover with the screw (x1).
Fix it with the screwB
(Packed items No.3)
Fix it with the screwC
(Packed items No.4)
Screw B(No.3)
Insert the harness fixing plate to
the groove of main unit.
the groove of main unit.
Connect the connector to the PWB.
MX-2630N MX-FN28 (FINISHER) 10 – 1
MX-2630N
Service Manual
[10] MX-FN28 (FINISHER)
1. Unpacking
A. Packed items check
B. Removal of the finisher
NOTE: It is recommendable to work by two or more persons.
1)
Cut the tapes at four corners, and remove the fixture.
2)
Take off the top case, and remove the cushioning materials.
3)
Take out the finisher from the plastic bag.
While holding the upper parts of the finisher by two people, pull up
the finisher, and then make it stand upright.
the finisher, and then make it stand upright.
C. Removal of the fixing tape and protection
material
1)
Remove the fixing tape/protection materials.
2)
Open the front upper cover, and remove the fixing tape/protection
materials.
materials.
No.
Name
Quantity
1
Shift tray
1
2
Guide plate
1
3
Screw (M3x6)
5
4
Screw (M4x8)
1
5
Screw (M4x12)
4
6
Earth plate
1
7
Bracket
1
1
2
3
4
5
6
7
MX-2630N MX-FN28 (FINISHER) 10 – 2
2. Installation
A. Installation of earth plate
1)
Install the earth plate (Packed items (No.6)) with the screws
(Packed item (No.3 M3x6)).
(Packed item (No.3 M3x6)).
B. Installation of the guide plate
1)
Install the guide plate (Packed items (No.2)) with the screws
(Packed item (No.3 M3x6)). For the positions of the screws,
please see the picture below.
(Packed item (No.3 M3x6)). For the positions of the screws,
please see the picture below.
C. Installation of the shift tray
1)
Insert the shift tray (Packed item No.1) into the finisher of the main
unit, and install the shift tray with the screw (Packed item No.4
M4x8)).
unit, and install the shift tray with the screw (Packed item No.4
M4x8)).
Click on the first or last page to see other MX-2630 service manuals if exist.