Sharp MX-2630 (serv.man6) Handy Guide ▷ View online
SHARP
COLOUR BALANCE ADJUSTMENT
MX-2630N Handy Guide NOV’17
Sharp Office Solutions Group
Page 13
/75
Troubleshooting - Standard Colour Calibration procedure when experiencing colour image quality issues:
Sim 22-06
Print and check consumable life, trouble & jam history.
Remove all Process Units, DV Units & MC Units and perform a thorough clean.
Clean the LSU Slit Glass
Clean the optical section.
Clean the ID sensors.
Sim 22-05
Check firmware version and update to the latest version.
Sim 44-27
Clear Half Tone Process Correction.
This simulation clears the previous high voltage compensation applied to DV&GB bias in order
to maintain a good image density level.
Sim 61-04
LSU Skew Adjustment.
Tolerance is approx. 1.5mm when measuring two diagonals.
Sim 50-10
LSU BK Magnification.
Check LSU BK Magnification - Inside dimension of the printed halftone must be 240±0.5mm
Sim 61-13
Laser F/R Evenness Correction Data Clear.
Sim 61-11
Laser F/R Evenness Correction Adjustment.
Use auto adjustment first. If the result is not satisfying, repeat before performing manual
adjustment.
Sim 50-22
Drum Phase & Colour Registration
Adjustment.
This simulation must be executed when the drums are replaced. Check for any F2-50/51/52/53
(Drum Phase) trouble before proceeding.
Sim 8-01
Check DV Bias.
Check DVB output value on label attached to MC PWB is the same as Sim8-01 settings.
Sim 8-02
Check GRID Bias.
Check GB output value on label attached to MC PWB is the same as Sim8-02 settings.
Sim 63-03
CCD Calibration - use Adjustment Chart
UKOG-0356FCZZ
.
To ensure the machine can read correct values from the print patterns produced during colour
calibration.
Sim 63-11
Default Engine Colour Balance Setting.
Sim 67-26
Default Printer Colour Balance Setting.
Sim 63-08
Reset Service & User Colour Balance for COPY mode
Clears the previous Service & Customer colour balance settings.
Sim 67-28
Reset Service & User Colour Balance for PRINTER mode.
Clears the previous Service & Customer colour balance settings.
Sim 46-74
Colour Calibration for COPY & PRINT modes.
Always select Factory mode unless Service colour balance is registered for customising colour
output.
Settings (Admin) -> Image Quality Adjustment -> Auto Colour Calibration for Copy.
Settings (Admin) -> Image Quality Adjustment -> Auto Colour Calibration for Print.
To reproduce colour consistently, the end user may need to conduct user calibration on a regular basis. For
clients who produce large volume prints, it is recommended to perform user calibration before the long run.
Settings (Admin) -> Image Quality Adjustment -> Auto Colour Calibration for Print.
To reproduce colour consistently, the end user may need to conduct user calibration on a regular basis. For
clients who produce large volume prints, it is recommended to perform user calibration before the long run.
Check colour output for both Copy & Print modes.
MINIMUM CALL PROCEDURE
SHARP
Page 14
/75
MX-2630N Handy Guide NOV’17
Sharp Office Solutions Group
MINIMUM CALL PROCEDURE:
SAMPLE PRINT/COPY:
Sim 64-01
A:11, B:2, C:2, D:255.
Sim 64-05
A:3, B:255
SERVICE CHART (Colour & B/W Mode)
MACHINE DATA [BEFORE]:
Sim 22-03
Check Jam History
Sim 22-04
Check Trouble Code History
Sim 22-05
Check ROM Versions
Sim 22-06
Print Patterns No 1 & 3
Sim 23-02
Print Jam/Trouble History
MAINTENANCE LIST
Check
Clean Replace*
1
Exterior
2
Operation Panel
3
Mirror (Optical Section)
4
SPF Glass
5
Document Glass (OC)
6
LSU Glass
7
MC Cleaning (Sim6-04 MC Cleaning Operation)
8
PTC Cleaning (Sim6-04 PTC Cleaning Operation)
9
Paper Pick-Up, Feed & Separation Rollers (Tray) – Sim22-03 Jam History
10
Paper Pick-Up, Feed & Separation Rollers (Bypass) – Sim22-03 Jam History
11
Main Charger (Sim 22-13 Life Counter)
12
OPC Drum (Sim 22-13 Life Counter)
13
Drum Cleaning Blade (Sim 22-13 Life Counter)
14
Developer (Sim 22-13 Life Counter)
15
Transfer Belt (Sim 22-13 Life Counter)
16
Transfer Blade (Sim 22-13 Life Counter)
17
Cleaning Roller (Sim 22-13 Life Counter)
18
Fusing Unit (Sim 22-13 Life Counter)
19
Image Density Sensor
FIRMWARE UPGRADE:
SIM 49-01
SIM 49-03
SIM 49-05
SIM 49-06
IMAGE QUALITY ADJUSTMENTS:
SIM 61-11
SIM 50-22
SIM 46-74
IMAGE CHECK [PRINT & COPY]:
SIM 64-01
SIM 64-05
SERVICE CHART COPY
MACHINE DATA [FINISH]:
SIM 22-06 (ALL)
* For Maintenance Item replacement (Simulation Counter reset), refer to the following Maintenance section
within this guide.
within this guide.
SHARP
MAINTENANCE
MX-2630N Handy Guide NOV’17
Sharp Office Solutions Group
Page 15
/75
MAINTENANCE INDICATIONS:
DK
Black Drum Counter has reached the specified life.
Replace Black OPC Drum
PROCESS
S
ECTION
DC
Cyan Drum Counter has reached the specified life.
Replace Cyan OPC Drum
DM
Magenta Drum Counter has reached the specified life.
Replace Magenta OPC Drum
DY
Yellow Drum Counter has reached the specified life.
Replace Yellow OPC Drum
MCK
Black Main Charge Counter has reached the specified life.
Replace K Main Charge Kit
MCC
Cyan Main Charge Counter has reached the specified life.
Replace C Main Charge Kit
MCM
Magenta Main Charge Counter has reached the specified life.
Replace M Main Charge Kit
MCY
Yellow Main Charge Counter has reached the specified life.
Replace Y Main Charge Kit
VK
Black Developer Counter has reached the specified life.
Replace Black Developer
VC
Cyan Developer Counter has reached the specified life.
Replace Colour Developer Kit
(CMY)
VM
Magenta Developer Counter has reached the specified life.
VY
Yellow Developer Counter has reached the specified life.
FK1
Fusing Belt Print Counter has reached the specified limit.
Replace the Fusing Belt Kit
FUSER
FK2
Pressure Roller Print Counter has reached the specified limit.
Replace the Pressure Roller Kit
TK1
Primary Transfer Unit Counter has reached the specified limit.
Replace the Primary Transfer
Belt & Blade Kits
TRANSFE
R
TK2
Secondary Transfer Unit Counter has reached the specified limit.
Replace the Secondary Transfer
Roller Kit
TK3
PTC Unit Counter has reached the specified limit.
Replace the PTC Unit
TA
Maintenance [All] Counter has reached specified limit
CA
Maintenance [Colour] Counter has reached specified limit
AA
Maintenance [All] & [Colour] Counters have reached the specified limits
Starting Powder:
The following starting powder should be applied to the relevant consumable item during maintenance:-
Starting Powder
OPC Drum
Primary Transfer Belt
MX-2630N
UKOG-0312FCZZ
[Stearic Acid]
CKOG-0345DS51
[Yellow Toner]
MAINTENANCE
SHARP
Page 16
/75
MX-2630N Handy Guide NOV’17
Sharp Office Solutions Group
MX-2630N
PROCESS SECTION – COLOUR:
(Colour maintenance counter has reached the specified life).
(Colour maintenance counter has reached the specified life).
Every
150K
Every
300K
Replace Cyan, Magenta & Yellow OPC Drum: (MX-60GRSA x 3)
Replace Cyan, Magenta & Yellow Main Charge Kits:-
• Main Charge Unit & Cleaning Blade (MX-407MK x 3)
x
Replace C, M, Y Developer (MX-60GVSA).
Clean LSU Dust Proof Glass (CMYK)
Sim 24-04
Clear Drum CTRG C, M, Y (Colour) Counters.
Clear Main Charger C, M, Y (Colour) Counters.
(MC Cleaner Counter is also cleared automatically)
Clear Drum Blade C, M, Y (Colour) Counters.
Clear Maintenance [Colour] Counter.
Sim 24-05
Clear Developer C, M, Y (Colour) Counters.
x
Remove ALL toner cartridges, prior to executing Sim 25-02.
x
Sim 25-02
Toner Concentration Adjustment - Select C, M, Y.
Note:
If ALL developer is replaced at the same time, select CMYK. When
Sim 25-02 is executed, the Developer Counter (Sim 24-05) is also
cleared automatically.
Sim 25-02 is executed, the Developer Counter (Sim 24-05) is also
cleared automatically.
x
Sim 44-27
Clear Half Tone Process Correction.
Every
180K
Every
360K
PROCESS SECTION -MONOCHROME:
(Total / K maintenance counter has reached the specified life).
(Total / K maintenance counter has reached the specified life).
Replace Black OPC Drum (MX-60GRSA).
Replace Black Main Charge Kit:-
• Main Charge Unit & Cleaning Blade (MX-407MK)
x
Replace Black Developer (MX-60GVBA).
Clean LSU Dust Proof Glass (CMYK)
Sim 24-04
Clear Drum CTRG K (Black) Counter.
Clear Main Charger K (Black) Counter.
(MC Cleaner Counter is also cleared automatically)
Clear Drum Blade K (Black) Counter.
Clear Maintenance [ALL] Counter.
x
Sim 24-05
Clear Developer K (Black) Counter.
x
Remove ALL toner cartridges, prior to executing Sim 25-02.
x
Sim 25-02
Toner Concentration Auto Adjustment - Select K.
Note:
If ALL developer is replaced at the same time, select CMYK. When
Sim 25-02 is executed, the Developer Counter (Sim 24-05) is also
cleared automatically.
Sim 25-02 is executed, the Developer Counter (Sim 24-05) is also
cleared automatically.
Click on the first or last page to see other MX-2630 (serv.man6) service manuals if exist.