Sharp MX-2610N / MX-3110N / MX-3610N (serv.man14) Service Manual ▷ View online
MX-3610N Dehumidifying heater 3 – 5
2. Installation
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Heater electric component kit installation
(1) External fixture removal
1)
Remove the rear cabinet.
2)
Remove the left cabinet.
3)
Remove the left cabinet lower.
(2) WH PWB attachment
1)
Remove the snap band. Attach the supporter, and attach the
WH PWB.
WH PWB.
(3) WH harness connection
1)
Remove the AC cord plate.
2)
Connect the WH harness, and attach the earth wire.
Pass the WH harness under the CCS-WH harness to the
switch.
switch.
Pass the WH harness under the MSW harness.
2
1
1
1
1
1
2
1
1
2
2
1
1
1
2
2
2
2
3
1
2
1
1
MSW harness
2
1
3
CSS-WH harness
WH harness
WH harness
MX-3610N Dehumidifying heater 3 – 6
3)
Attach the AC cord plate.
(4) Dehumidifier heater control switch attachment
1)
Connect the WH harness to the dehumidifier heater control
switch, and attach the dehumidifier heater control switch.
switch, and attach the dehumidifier heater control switch.
2)
Cut away the dehumidifier heater control switch section on the
rear cabinet.
Attach the dehumidifier heater control switch label to the rear
cabinet.
rear cabinet.
Attach the dehumidifier heater control switch label to the rear
cabinet.
B. Heater kit installation
(1) Heater unit assembly
1)
Attach the heater to the heater mounting plate and secure it
with the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
with the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
2)
Attach the heater mounting plate to the T-Heater cover and
secure it with the screw (M3 x 6 S-tight).
secure it with the screw (M3 x 6 S-tight).
3)
Attach the CSS-WH harness to the heater mounting plate, and
connect the harness of the dehumidifier heater. Fix the earth
wire with a screw.
connect the harness of the dehumidifier heater. Fix the earth
wire with a screw.
1
2
1
2
1
DH
PO
WER
PO
WER
1
2
3
1
2
2
2
1
MX-3610N Dehumidifying heater 3 – 7
(2) Heater unit attachment
1)
Remove the tray 1.
2)
Attach the heater unit to the main unit, and secure it with the
screw (M4 x 10 P-tight).
Pass the harness of the heater through the hole on the main
unit frame.
screw (M4 x 10 P-tight).
Pass the harness of the heater through the hole on the main
unit frame.
3)
Fix the earth wire with a screw. Connect the connector.
Pass the WH harness under the CCS-WH harness to the
switch.
switch.
(3) External fixture attachment
1)
Attach the left cabinet lower.
2)
Attach the left cabinet.
3)
Attach the rear cabinet.
2
1
CSS-WH harness
WH harness
1
2
2
1
2
1
2
2
2
2
2
MX-3610N Dehumidifying heater 3 – 8
C. Scanner heater kit installation
(1) External fixture removal
1)
Remove the paper exit cover.
2)
Remove the left cabinet.
3)
Remove the left cabinet upper.
4)
Remove the rear upper cabinet.
5)
Remove the rear cabinet.
(2) SCN-WH harness connection
1)
Remove the harness guide.
2)
Connect the SCN-WH harness connector to the scanner
frame.
frame.
2
1
1
2
1
2
2
1
1
1
2
2
1
1
1
1
1
3
4
2
1
1
2
Click on the first or last page to see other MX-2610N / MX-3110N / MX-3610N (serv.man14) service manuals if exist.