Sharp MX-2610N / MX-3110N / MX-3610N (serv.man14) Service Manual ▷ View online
MX-3610N Dehumidifying heater 3 – 17
2)
Pull the harness tightly in the arrow direction, and check to
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
confirm that there is no disconnection of the snap band and
that the square hole in the frame is not covered with the har-
ness.
3)
Connect the connector of the heater harness unit, and attach
the earth wire.
the earth wire.
Attach the earth wire at an angle of 45 degrees.
(5) Cabinet and heater cover attachment
1)
Attach the cabinet.
2)
Attach the heater cover.
(6) Paper feed unit attachment
1)
Attach the paper feed unit.
45q
2
1
2
1
2
1
2
MX-3610N Dehumidifying heater 3 – 18
2)
Attach the upper cabinet.
3)
Close the upper cover.
4)
Insert the paper feed tray.
(7) Connector connection
1)
Remove the connector cover.
2)
Connect the connector, and tighten the screw.
F. Operation check after installation
1)
Turn on the dehumidifier heater switch.
2)
Measure the resistance value between the earth terminal and
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
the AC terminal (L side), and between the earth terminal and
AC terminal (N side) with the circuit tester, and confirm they
are not short-circuited.
3)
When not using the dehumidifier heater after checking, turn off
the dehumidifier heater switch.
the dehumidifier heater switch.
2
1
3
3
2
2
1
1
2
MX-3610N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 1
MX-3610N
Service Manual
[4] MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER
DRAWER)
1. Unpacking
If the connector is removed first, it may be damaged during the
installation procedures. Therefore, keep it packed while un-box-
ing. and unpack it only when connecting the connector to the
machine.
installation procedures. Therefore, keep it packed while un-box-
ing. and unpack it only when connecting the connector to the
machine.
A. Packed items check
2. Installation
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Right adjuster attachment
1)
Attach the right adjuster included in the package to the desk
unit.
unit.
Insert the right adjuster until it is locked.
2)
Turn each adjuster to fix the desk unit.
No.
Name
Quantity
1
Desk unit
1
2
Right adjuster
1
3
Fixing screws (M3 x 8)
4
4
Connection cover
2
2
1
4
3
MX-3610N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 2
B. Main unit and desk unit connection
1)
Put the main unit on the desk unit.
Use man power of four persons or more to lift the main unit.
Place the main unit on the desk unit slowly by fitting the exter-
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
2)
Remove the tray 1 and the tray 2.
3)
Raise the linkage plates on the right and left sides of the front
side of the desk unit, and fix them with the fixing screws
included in the package.
side of the desk unit, and fix them with the fixing screws
included in the package.
4)
Attach the tray 1 and the tray 2.
5)
Raise the linkage plates on the right and left sides of the rear
side of the desk unit, and fix them with the fixing screws
included in the package.
side of the desk unit, and fix them with the fixing screws
included in the package.
2
1
2
1
2
1
2
1
Click on the first or last page to see other MX-2610N / MX-3110N / MX-3610N (serv.man14) service manuals if exist.