DOWNLOAD Sharp MX-2610N / MX-3110N / MX-3610N (serv.man14) Service Manual ↓ Size: 26.68 MB | Pages: 127 in PDF or view online for FREE

MX-3610N  MX-2010U/2310U/3111U/2610N/3110N/3610N (MAIN UNIT)  2 – 5

11) Re-install the waste toner box and lock into place.

Setting of the reference toner density control level must be per-
formed with the toner cartridge removed.
If setting is performed with the toner cartridge installed, the EE-EL
error or an overtoner trouble may occur.

1)

With the front cabinet open, connect the power plug to the
power outlet.

2)

Turn ON the main power switch of the machine and the power
switch on the operation panel.

3)

Enter the SIM25-2 mode.

4)

After entering the simulation, close the front cabinet.

5)

Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density. (Operating times: approx. 1.5 minutes)

Be sure to select all of the four colors: K, C, M, Y.

6)

After the machine completes cycling, exit the simulation mode.

7)

Confirm that “Install the toner cartridge” is displayed, and
install the toner cartridge by the following procedures.

8)

Shake the toner cartridge horizontally several times.

9)

Open the front cabinet, and insert each toner cartridge.

Be sure to install the color cartridges to their proper positions.
Avoid installation to a different color position.

Do not forcibly insert the toner cartridge.
Push it in until the cartridge is securely locked in place.

Developing units removed, be sure to remove the toner car-
tridges as well to prevent toner clogging.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

MX-3610N  MX-2010U/2310U/3111U/2610N/3110N/3610N (MAIN UNIT)  2 – 6

10) Close the front cabinet.
11) Confirm that "Toner replenishment in progress" is displayed,

and wait until the display disappears. (It takes 30 sec - 6 min.)

This procedure is for checking the toner supply operation from
the toner cartridge to the DV unit. The operation time differs
depending on the toner quantity in the toner cartridge, uneven
distribution of toner, and the inside state of the toner cartridge.

Do not perform operations which interrupt the above operation,
such as opening the front cover, entering the SIM mode, and
turning OFF/ON the power. If this precaution is ignored, an
error of F2-40 - 43 or F2-64 - 67 may occur or an overtoner
may be caused.

Dust from the transfer belt or shutter or some other adjacent part
may fall onto the LSU during transport or installation. Be sure to
clean the dust-proof glass and PTC wire before checking the image
quality.

1)

Open the front cabinet. Slide the lock to release, and remove
the waste toner box.

2)

Detach the LSU cleaning bar from the front cover.

3)

Turn the felt side of the cleaning bar downward and insert it.
Slide it back and forth a few times to clean the LSU dust-proof
glass.

4)

Move the PTC cleaning rod back and forth a few times to clean
the PTC wire.

After completion of cleaning, insert the cleaning rod completely
to the bottom.

Y

M

C

BK

MX-3610N  MX-2010U/2310U/3111U/2610N/3110N/3610N (MAIN UNIT)  2 – 7

5)

Return the LSU cleaning rod to the front cabinet so that the felt
faces upward. Fit the boss, and fix it with three pawls.

6)

Close the front cabinet.

1)

Press the [SYSTEM SETTINGS] key.

2)

Touch the [Paper Tray Settings] key.

3)

Touch the [Paper Tray Settings] key to configure the settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.

4)

Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.

1)

Pull out the paper tray.
Gently pull the tray out until it stops.
If paper remains in the tray, remove it.

2)

Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.

Use simulation 26-6 to set the machines destination.

After completion of destination settings, change the set values to
customize the following settings.

Type

Select the type of paper that is loaded in the tray. 
The paper types that can be selected vary by paper 
tray.

Size

Select the paper size from the list. The paper sizes 
that can be selected vary by tray. The sizes that 
can be selected may also be restricted by the paper 
type selected above. 
If the desired size does not appear in the list, select 
[Custom Size] and directly enter the size (only for 
the bypass tray).

Feeding Approved 
Job

Select the modes that can be used. If there is a 
function that you do not wish to be used with the 
selected tray, disable the function. When the "Type" 
is other than plain paper, recycled paper, colored 
paper, or a user type, [Fax] and [Internet Fax] 
cannot be selected.

26

6

Used to set the destination.

26

3

Used to set the auditor specification mode.

5

Used to set the count mode of the total counter and 
the maintenance counter.

18

Used to set YES/NO of the toner save mode (Only 
in UK and Japan versions)
* For other destination versions, this setup is 

made by the user program.

52

Used to set YES/NO of counting when non-print 
paper is passed through each counter.

53

Used to set YES/NO of user calibration permission.

65

Used to set the limit number of sheets for stapling.

A

B

MX-3610N  MX-2010U/2310U/3111U/2610N/3110N/3610N (MAIN UNIT)  2 – 8

Execute the following items.

*1: When a printer option is installed, be sure to execute the above
item.

This adjustment performs the print engine image distortion adjust-
ment, the OPC drum phase adjustment, and the color registration
adjustment simultaneously.
1)

Enter SIM50-22 mode.

1

Print engine image distortion adjustment (Manual 
adjustment) / OPC drum phase adjustment 
(Automatic adjustment) / Color registration 
adjustment (Automatic adjustment)

50-22

2

Copy color balance and density check

3

Printer color balance/density check

64-5/67-25

4 

*1

Copy/Printer color balance and density adjustment 
(Automatic adjustment)

46-74

EXECUTE

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

12:(;(&87,1*

(;(&87(

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

35(66>(&(;87(@7267$57

(55257211(5(037<

(;(&87(

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872$'-8670(172)5(*,675$7,21 '580326,7,21

0$,1)0$,1568%6.(:3+$6(

&/1*

0/1*

</1*

$//B527$7(/2.

(;(&87(

Adjustment completed

Abnormal end