DOWNLOAD Sharp AR-M700 (serv.man27) Service Manual ↓ Size: 948.19 KB | Pages: 97 in PDF or view online for FREE

: Feb. 9 2004

AR-M550/M620/M700  SIMULATION  8 - 41

1) Press [START] key.

The developing motor and the OPC drum motor rotate, and the
toner concentration detection level and the humidity sensor detec-
tion level are displayed.

1) Press [START] key.

The developing motor rotates for 3 min and the toner concentration
sensor makes sampling of toner concentration to display the
detection level.

After the developing motor stops, the average value of toner con-
centration sampling is set as the reference toner concentration
level.

NOTE: When the above operation is interrupted on the way, the refer-

ence toner concentration level is not set. Also when error code
of EE-EL or EE-EU is displayed, the reference toner concentra-
tion level is not set normally.

 (Default: 114)

1) Select the number corresponding to the paper feed unit for setting

the paper size with 10-key. 

2) Press [START] key.

3) Select the number corresponding to the paper size. 

4) Press [START] key.

1) Select the number corresponding to the auditor mode with 10-key. 

2) Press [START] key.

(Default: 1)

Press [START] key.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 3 min.

25-2

Setting

Used to make the initial setting of toner concentration 
when replacing developer.

Image process (Photoconductor/Developing/Transfer/
Cleaning)

2) The humidity near the developing tank at the developing adjust-

ment is registered.

Press [START] key.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped immediately or after 3 min.

SIMULATION 25-1

TONER SENSOR OUTPUT MONITOR. PRESS START.

HUMIDITY AREA :   

70.0

 - 

72.5

DEVE REFERENCE :  

128

SIMULATION 25-1

DV MONITOR. EXECUTING···.

HUMIDITY AREA :   

70.0

 - 

72.5

DEVE REFERENCE :  

128

SIMULATION 25-2

AUTOMATIC DV ADJUSTMENT. PRESS START.

HUMIDITY AREA :   

70.0

 - 

72.5

DEVE REFERENCE :  

114

SIMULATION 25-2

AUTOMATIC DV ADJUSTMENT. EXECUTING···.

HUMIDITY AREA :   

70.0

 - 

72.5

DEVE REFERENCE :  

114

26-2

Setting

Used to set the paper size of the large capacity tray 
(LCC) and the paper feed tray 2. (When the paper size 
is changed, this simulation must be executed to 
change the paper size in software.)

Paper feed

Setting

1

TRAY 2

TRAY 2 size (0 = 8.5 x 11, 1 = A4, 2 = B5)

2

LCC

Side LCC size  (0 = 8.5 x 11, 1 = A4, 2 = B5)

Press [START] key.

Press [CUSTOM SETTINGS] key.

26-3

Setting

Used to set the specifications of the auditor. Setting 
must be made according to the auditor use conditions.

Auditor

Specifications

1

P10

Built-in auditor mode

2

VENDOR

Coin vendor mode

3

OTHERS

Other

SIMULATION 26-2

1

SIZE SETUP. SELECT NUMBER, AND PRESS START.

1. TRAY2           

2. LCC             

SIMULATION 26-2

LCC SIZE SETUP. SELECT 0-2, AND PRESS START.

0. 8.5x11

1. A4

2. B5

1

SIMULATION 26-3

AUDITOR SETUP. SELECT 1-3, AND PRESS START.

1. P10

2. VENDOR

3. OTHERS

1

AR-M550/M620/M700  SIMULATION  8 - 42

1) Select the number corresponding to the counter to be set with 10-

key. 

2) Press [START] key. 

3) Select the count mode with 10-key.

4) Press [START] key.

Set the count-up (1 or 2) for A3/WLT paper.

(Select the target counter.)

(Count-up)

1) Select the number corresponding to the destination with 10-key. 

2) Press [START] key.

After completion of setting, the machine is automatically reset.

Since this simulation cannot change the Fax destination, use SIM 66-2
to change the FAX destination.

1) Select START/END of the network scanner trial mode with 10-key. 

2) Press [START] key.

Max. 500 menus can be scanned.

1) Select YES/NO of the toner save mode with 10-key. 

2) Press [START] key.

1) Select the number corresponding to the operation mode with 10-

key.

2) Press [START] key.

(Default: 1 for Europe, 0 for the others)

26-5

Setting

Used to set the count mode of the total counter and the 
maintenance counter.

Specifications

Counter

1

TOTAL COUNTER

Total counter

2

MAINTENANCE (DRUM) 
COUNTER

Maintenance counter/ OPC 
drum counter

3

DV COUNTER

Developer counter

1

1 COUNT UP

1 count-up

2

2 COUNT UP

2 count-up

Default

Press [START] key.

Press [CUSTOM SETTINGS] key.

26-6

Setting

Used to set the specifications (paper, fixed 
magnification ratio, etc.) of the destination.

Specifications

Destination

1

USA

United States of America

2

CANADA

Canada

3

INCH

Inch series EX

4

JAPAN

Japan

5

AB_B

AB series B5

6

EUROPE

Europe

7

UK

UK

8

AUSTRALIA

Australia

9

AB_A

AB series A5

10

CHINA

China

SIMULATION 26-5

1

A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS

START.

1. TOTAL COUNTER 

1

2. MAINTENANCE(DRUM) COUNTER 

1

3. DV COUNTER 

1

SIMULATION 26-5

A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS

START.

1. TOTAL COUNTER

(1: 1COUNT UP,  2: 2COUNT UP)

1

26-10

Setting

Used to set the network scanner trial mode.

Operation

0

END

Trial mode cancel

Default

1

START

Trial mode start

26-18

Setting

Used to set YES/NO of toner save operation. (This 
function is valid only in Japan and UK versions. 
(Depends on the destination setting of SIM26-6.) For 
the other destinations, the same setting can be made 
by the user program P22.)

Specifications

Operation mode

0

YES

Toner save mode is set.

1

NO

Toner save mode is not set.

Default

26-30

Setting

Used to set the operation mode conforming to the CE 
mark (Europe safety standards). (Conforming to soft 
start when driving the fusing heater lamp.)

Specifications

Operation mode (Common)

0

NO

CE mark control NO (Normal operation)

1

YES

CE mark control YES (Heater lamp soft start operation)

SIMULATION 26-6

DESTINATION SETUP. SELECT 1-10, AND PRESS START.

1.USA 2.CANADA 3.INCH

4.JAPAN 5.AB_B

6.EUROPE 7.UK 8.AUSTRALIA

9.AB_A   10.CHINA

1

SIMULATION 26-10

NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS

START.

0.END

1.START

1

SIMULATION 26-18

TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START.

0. YES

1. NO

1

: Feb. 9 2004

AR-M550/M620/M700  SIMULATION  8 - 43

1) Select the number corresponding to the operation mode with 10-

key.

2) Press [START] key.

(Default: 0)

1) Select the number corresponding to the operation mode with 10-

key.

2) Press [START] key.

(Default: 0)

2) Press [START] key.

(Default: 1 for Europe and UK, 0 for the others)

1) Select ENABLE/DISABLE of the B/W reverse mode with 10-key.

2) Press [START] key.

1) Select YES/NO of the non-print paper count-up with 10-key.

2) Press [START] key. 

Non-print paper means an insert paper (without copying) in the OHP
insertion mode, a cover (without copying) in the cover insertion mode,
back surface, and white paper in the duplex exit mode (CA, etc.).

(Default: 0 for Japan and Australia, 1 for the other)

The target counters are as follows:

• Copies counter

• Printer counter

• Department management counter

26-35

Setting

Used to set whether the same continuous troubles are 
displayed as one trouble or the series of troubles with 
SIM 22-4 when the same troubles occur continuously.

Specifications

0

ONCE

When two or more troubles of a same kind occur 
continuously, the troubles are displayed as one 
trouble in the trouble history of SIM22-4. 

1

ANY

When two or more troubles of a same kind occur 
continuously, the troubles are displayed straightly as 
two or more troubles in the trouble history of SIM22-
4. 

26-38

Setting

Used to set CONTINUE/STOP of printing when 
maintenance timing is over and the count value 
reaches 110% of replacement timing (life). 

Other

Specifications

0

PRINT CONTINUE

Print continue

1

PRINT STOP

Print stop

SIMULATION 26-30

CE MARK CONTROL SETTING. SELECT 0-1, AND PRESS START.

0. NO

1. YES

1

SIMULATION 26-35

TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS

START.

0. ONCE

1. ANY

1

SIMULATION 26-38

LIFE OVER SETTING. SELECT 0-1, AND PRESS START.

0. PRINT CONTINUE

1. PRINT STOP

1

26-41

Setting

Used to set YES/NO of the automatic magnification 
ratio selection (AMS) in the pamphlet mode.

Specifications

Operation mode (Common)

1) Enter the number corresponding to whether AMS operation is

automatically performed or nor in the center binding mode with the
10-key. 

0

NO

AMS/APS selection allowed

1

YES

AMS is forcibly operated. 

26-50

Setting

Black-White reverse YES/NO setting

Specifications

Operation

0

DISABLE

B/W reverse mode DISABLE

1

ENABLE

B/W reverse mode ENABLE

Default

26-52

Setting

Used to set whether non-print paper (insertion paper, 
cover paper) (blank image print paper) is counted up or 
not.

Paper transport (Discharge/Switchback/Transport)

Specifications

Operation mode

0

NO (NO COUNT UP)

No count up

1

YES (COUNT UP)

Count up

• Total counter

• Effective paper counter

SIMULATION 26-41

PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS 

START.

0. NO

1. YES

1

SIMULATION 26-50

B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS 

START.

0. DISABLE

1. ENABLE

1

AR-M550/M620/M700  SIMULATION  8 - 44

1) Select ENABLE/DISABLE of the CA key cancel function of print

stop with 10-key.

2) Press [START] key.

(Default: 1)

1) Select the number corresponding to the operation mode with 10-

key.

2) Press [START] key.

(Default: 0)

1) Enter the tag number with 10-key.

2) Press [START] key.

The operating conditions of sensors and detectors are displayed.

The active sensors and detectors are highlighted.

26-68

Setting

Used to set ENABLE/DISABLE of the CA key cancel 
function of print stop.

Specifications

Operation

0

DISABLE

Disable

1

ENABLE (PRINT STOP)

Enable

27-1

Setting

Used to set the specifications for operations in case of 
communication trouble between the host computer and 
MODEM (machine side). (When communication 
trouble occurs between the host computer MODEM 
and the machine, the self diag display (U7-00) is 
printed and setting for inhibition of print or not is made.)

Communication unit (TEL/LIU/MODEM etc.)

Specifications

Operation mode

0

YES

Though a communication trouble occurs between the 
host computer and the MODEM (machine side), there is 
no effect on the machine operations.

1

NO

When a communication trouble occurs between the host 
computer and the MODEM (machine side), the self diag 
display (U7-00) is displayed and printing is inhibited.

SIMULATION 26-52

BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS 

START.

0. NO  (NO COUNT UP)

1. YES (COUNT UP)

1

SIMULATION 26-68

CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS 

START.

0. DISABLE

1. ENABLE (PRINT STOP)

0

SIMULATION 27-1

DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.

0. YES

1. NO

1

27-5

Setting

Used to enter the machine tag No. (This function 
allows to check the tag No. of the machine with the 
host computer.)

Communication unit (TEL/LIU/MODEM etc.)

Specifications

Operation mode

30-1

Operation test/Check

Used to check the operation of sensors and detectors 
in other than the paper feed section and the operations 
of the related circuits.

Operation

PFD2

ADU paper feed detection 2

PPD

Resist roller front paper detection 

PSD

Drum rear paper detection 

POD1

After-fusing transport detection 1

POD2

After-fusing transport detection 2

POD3

Paper full detection

DSW_R

Manual feed door open detection

DSW_L

Cabinet open detection

DSW_F

Front cabinet open detection 

DSW_DSK

Desk door open detection 

TFSD

Toner remaining quantity detection (Motor rotation 
number count)

THPS2

Transfer belt separation home sensor 2

LPPD

LCC paper transport detection

T1PPD

Tandem tray 1 paper transport sensor

SIMULATION 27-5

TAG # SETTING. INPUT VALUE, AND PRESS START.

PRESENT:  00010000

NEW:      

SIMULATION 30-1

SENSOR CHECK..
PFD2        

       PSD       POD1      POD2

POD3        DSW_R     DSW_L     DSW_F
DSW_DSK     TFSD      THPS2     LPPD      T1PPD