Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ▷ View online
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 7
C. Details
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press START key.
The scanner performs scanning at the speed corresponding to
the operation mode.
the operation mode.
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
• The scanner (read) unit is in the home position.: "MHPS" section
is highlighted.
• The scanner (read) unit is not in the home position.: "MHPS" is
normally displayed.
Operation/Procedure
1) Select the operation mode with 10-key.
2) Press START key.
The SPF repeat paper feed, transport, and paper exit at the
speed corresponding to the operation mode.
speed corresponding to the operation mode.
The operation can be stopped by [CUSTOM SETTINGS] key.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
1
1-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the scanner
(read) unit and its control circuit.
(read) unit and its control circuit.
Section
Optical (Image scanning)
Item
Operation
1
TOP SPEED
Top speed (220mm/s)
2
HIGH SPEED
High speed (168.7mm/s)
3
MIDDLE SPEED
Middle speed (110mm/s)
4
LOW SPEED
Low speed (55mm/s)
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and
scanning is stopped.
scanning is stopped.
1-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and
detector in the scanning (read) section and the
related circuit.
detector in the scanning (read) section and the
related circuit.
Section
Optical (Image scanning)
Item
Operation
MHPS
Optical system home position
SIMULATION 1-1
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
SCANNER CHECK. SELECT 1-4, AND PRESS START.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
1
SIMULATION 1-1
SCANNER CHECK. EXECUTING···.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
SCANNER CHECK. EXECUTING···.
1. TOP SPEED
2. HIGH SPEED
3. MIDDLE SPEED
4. LOW SPEED
1
SIMULATION 1-2
SCANNER SENSOR CHECK..
MHPS
2
2-1
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the automatic
document feeder unit and the control circuit.
document feeder unit and the control circuit.
Section
DSPF
Item
Operation
1
HIGH SPEED
High speed
2
LOW SPEED
Low speed
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
the operation is stopped.
2-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the automatic document feeder unit
and the related circuits.
detectors in the automatic document feeder unit
and the related circuits.
Section
DSPF
Item
Operation
SPFSET
SPF sensor
SOCD
Open/close sensor
SCOV
Paper feed cover sensor
SPED
Document set sensor
SPPD
Resist front detection sensor
SPOD
Document paper exit sensor
SWDn
Document width sensor (n
→
1 (inside) - 6
(outside))
SPLSn
Document length sensor (n
→
1 (inside) - 2
(outside))
CISSET
CIS installation detection
STSET
Stamp unit installation sensor
SWD_LEN
SPF guide plate position (unit: 0.1mm)
SWD_AD
SPF document width detection volume output AD
value
value
SIMULATION 2-1
SPF AGING TEST. SELECT 1-2, AND PRESS START.
1. HIGH SPEED
2. LOW SPEED
2
SIMULATION 2-1
SPF AGING TEST. EXECUTING···.
1. HIGH SPEED
2. LOW SPEED
2
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 8
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
• The following units are added when the punch unit is installed to
the console finisher:
2-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the loads in the
automatic document feeder unit and the control
circuits.
automatic document feeder unit and the control
circuits.
Section
DSPF
Item
Operation
1
MOTOR(H)
Motor high speed
2
MOTOR(L)
Motor low speed
3
SDSS
SPF gate solenoid
4
SPFS
SPF pick-up solenoid
5
SPFC
SPF paper feed clutch
6
SRRC
SPF resist roller clutch
7
STMPS
Stamp solenoid
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
operation is stopped.
3
3-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and
detector in the finisher and the related circuit.
detector in the finisher and the related circuit.
Section
Finisher
Item
Operation
SIMULATION 2-2
SPF SENSOR CHECK.
SPFSET
SOCD
SCOV
SPED
SPPD SPOD
SWD6
SWD5
SWD4 SWD3 SWD2 SWD1
SPLS2 SPLS1
CISSET
STSET
SWD_LEN:
2100
SWD_AD:
600
SIMULATION 2-3
SPF LOAD TEST. SELECT 1-7, AND PRESS START.
1.MOTOR(H) 2.MOTOR(L)
3.SDSS 4.SPFS 5.SPFC 6.SRRC
7.STMPS
2
SIMULATION 2-3
SPF LOAD TEST. EXECUTING···.
1.MOTOR(H) 2.MOTOR(L)
3.SDSS 4.SPFS 5.SPFC 6.SRRC
7.STMPS
2
Built-in finisher
STHP
Stapler HP detection
POD
Tray 2 paper exit detection
SCID
Staple compiler paper entry detection
PID
Paper entry detection
T2PD
Tray 2 paper empty detection
T2DN
Tray 2 lower limit detection
T2UP
Tray 2 upper limit detection
JRHP
Jogger R HP
JFHP
Jogger (F) HP
SCID2
Staple compiler paper entry detection 2
STTHP2
Staple rotation HP detection 2
STTHP1
Staple rotation HP detection 1
STUHP
Staple shift HP detection
PSHP
Pusher HP detection
PPD
Paper hold return detection
DSW2
Staple replacement door open detection
DSW1
Compiler jam cancel door open detection
24VM
24V power supply
T1PF
Tray 1 full detection
STSP
Stapling ready detection
STLS
Cartridge inside spare staple empty detection
STNC
Cartridge empty detection
DOPD
Interface unit door open detection
MMLK
Main drive motor lock detection
SCPD
Staple compiler paper empty detection
Console finisher
FSSS
Stapler safety switch
FJS
Joint switch
FFDSW
Front door switch
FTCS
Upper cover sensor
FFDS
Front door sensor
FSPS
Self prime sensor
FSUC
Stapler connection detection
FSS
Staple sensor
FSTHPS
Stapler HP sensor
FSHPS
Slide HP sensor
FLE
Lift lock sensor
FLLLS
Lift lower limit sensor
FULS
Lift upper limit sensor
FFE
Bookbinding clock sensor
FFES
Bookbinding paper sensor
FFRHPS
Bookbinding roller HP sensor
FFHPS
Bookbinding HP sensor
FFPS
Bookbinding position sensor
FSLS
Paper surface sensor
FBES
Tray paper sensor
FOBHPS
Paper exit belt HP sensor
FAS
Alignment tray sensor
FRJHPS
Alignment HP sensor R
FFJHPS
Alignment HP sensor F
FARHPS
Bundle roller HP sensor
FPHPS
Paddle HP sensor
FES
Entry port sensor
FPE
Punch motor encoder
FPSHPS
Punch side register HP
FPUC
Punch connection detection
FPDS
Punch dust sensor
FPDSS4
Punch side register sensor 4
FPDSS3
Punch side register sensor 3
FPDSS2
Punch side register sensor 2
FPDSS1
Punch side register sensor 1
FPTS
Punch timing sensor
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 9
(Built-in finisher)
(Console finisher)
( ) : Added when the punch unit is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the
load.
load.
Operation/Procedure
Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
3-3
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operation of the load in the
finisher and the control circuit.
finisher and the control circuit.
Section
Finisher
Item
Operation
Built-in finisher
1
T2S
Tray 2 solenoid
2
T2OM
Paper exit motor
3
SPS
Stopper solenoid
4
SCRS
Roller pressure release solenoid
5
PPS
Rear edge h folding solenoid
6
SCGS
Compiler gate solenoid
7
STTM
Staple rotation motor
8
STUM
Stapler shift motor
9
MM
Main drive motor
10
EVM
Elevator motor
11
STM
Staple motor
12
JRM
Jogger motor rear
13
JFM
Jogger motor front
14
PSM
Pusher motor
Console finisher
1
FFC
Folding clutch
2
FPSM
Puncher side register motor
3
FPNM
Punch motor
4
FLM
Shift motor
5
FFSM
Stapler motor
6
FSM
Slide motor
7
FRJM
Alignment motor R
8
FFJM
Alignment motor F
9
FAM
Bundle exit motor
10
FPM
Paddle motor
11
FFM
Transport motor
SIMULATION 3-3
FINISHER SENSOR CHECK.
PID SCID SCID2 PPD
SCPD POD T1PF T2UP
T2DN T2PD STSP STLS
STNC STHP JFHP JRHP
PSHP STUHP STTHP1
STTHP2 DOPD DSW1 DSW2
24VM MMLK
SIMULATION 3-2
FINISHER SENSOR CHECK.
FSSS FJS FFDSW FTCS FFDS
FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS
FULS FFE FFES FFRHPS FFHPS FFPS FSLS
FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS
FES
(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)
(FPDSS1)(FPTS)
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
the operation is stopped.
3-6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the stacking capacity of the
finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
direction. The adjustment is made by changing the
alignment plate home position in the paper width
direction by software.)
finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
direction. The adjustment is made by changing the
alignment plate home position in the paper width
direction by software.)
Section
Finisher
Item
Operation
Press [START] key, and the
operation is started.
operation is started.
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
Stops when the operation is terminated.
operation is stopped.
Stops when the operation is terminated.
3-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Console finisher (AR-FN7) adjustment
Section
Finisher
Item
Operation
Item
Set
range
Initial
value
value
1STEP
1
Saddle binding position
adjustment
adjustment
0 - 400
200
0.0707mm
2
Saddle folding position
adjustment
adjustment
0 - 400
200
0.0525mm
3
Front alignment position
adjustment
adjustment
0 - 20
10
0.367mm
4
Rear alignment position
adjustment
adjustment
0 - 20
10
0.367mm
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1-
AND PRESS START.
2
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING
.
2
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
50
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING....
50
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 10
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the load.
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
played.
The active sensors and detectors are highlighted.
5
Staple rear one-position
binding position adjustment
binding position adjustment
0 - 200
100
0.04374mm
6
Staple front one-position
binding position adjustment
binding position adjustment
0 - 200
100
0.04374mm
7
Staple 2-position binding
center adjustment
center adjustment
0 - 200
100
0.04374mm
8
Staple 2-position binding pitch
adjustment
adjustment
0 - 99
50
0.04374mm
9
Punch center adjustment
(Slide direction)
(Slide direction)
47 - 53
50
1mm
10 Punch hole position
adjustment (Paper feed
direction)
direction)
0 - 99
50
0.105mm
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
the operation is stopped.
3-20
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the mail bin stacker sensor.
Section
Mail bin stacker
Item
Operation
MPFD1
Tray 1 paper full detection
MPFD2
Tray 2 paper full detection
MPFD3
Tray 3 paper full detection
MPFD4
Tray 4 paper full detection
MPFD5
Tray 5 paper full detection
MPFD6
Tray 6 paper full detection
MPFD7
Tray 7 paper full detection
MPFD8
Tray 8 paper full detection
MPID
Interface unit paper entry detection
MPPD1
Paper transport sensor 1
MPPD2
Paper transport sensor 2
MPPD3
Paper transport sensor 3
MPPD4
Paper transport sensor 4
MPPD5
Paper transport sensor 5
M24VM
24V power supply
MDD1
Jam cancel door
MDOPD
Interface unit door
Item
Set
range
Initial
value
value
1STEP
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10,AND PRESS START.
1.SADDLE POSITION 2.FOLDING POSITION
3.FRONT ADJUST
4.REAR ADJUST 5.STAPLE REAR
6.STAPLE FRONT 7.STAPLE BOTH
8.STAPLE PITCH 9.PUNCH CENTER
10.PUNCH HOLE
CONSOLE FINISHER SETTING. SELECT 1-10,AND PRESS START.
1.SADDLE POSITION 2.FOLDING POSITION
3.FRONT ADJUST
4.REAR ADJUST 5.STAPLE REAR
6.STAPLE FRONT 7.STAPLE BOTH
8.STAPLE PITCH 9.PUNCH CENTER
10.PUNCH HOLE
1
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1.FOLDING POSITION
200
SIMULATION 3-20
MAIL BOX SENSOR CHECK.
MPFD1
MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7
MPFD8 MPID MPPD1 MPPD2 MPPD3 MPPD4 MPPD5
M24VM MDD1 MDOPD
3-21
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the mail bin
stacker loads.
stacker loads.
Section
Mail bin stacker
Item
Operation
1
MM
Main motor
2
GSOL1
Gate solenoid 1
3
GSOL2
Gate solenoid 2
4
GSOL3
Gate solenoid 3
5
GSOL4
Gate solenoid 4
6
GSOL5
Gate solenoid 5
7
GSOL6
Gate solenoid 6
8
GSOL7
Gate solenoid 7
Press [START] key, and the operation
is started.
is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
the operation is stopped.
4
4-2
Purpose
Operation test/Check
Function
(Purpose)
(Purpose)
Used to check the operations of the sensors and
detectors in the paper feed section (desk paper
feed/large capacity tray) and the related circuit.
detectors in the paper feed section (desk paper
feed/large capacity tray) and the related circuit.
Section
Paper feed
Item
Operation
SIMULATION 3-21
MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2
SIMULATION 3-21
MAIL BOX LOAD TEST. EXECUTING....
1.MM
MAIL BOX LOAD TEST. EXECUTING....
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7
2
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man17) service manuals if exist.