DOWNLOAD Sharp AR-M351U / AR-M451U (serv.man17) Service Manual ↓ Size: 887.33 KB | Pages: 88 in PDF or view online for FREE

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 9

(Built-in finisher)

(Console finisher)

( ) : Added when the punch unit is installed.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press START key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the
load.

Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [START] key. (The entered value is stored.)

3-3

Operation test/Check

Used to check the operation of the load in the 
finisher and the control circuit.

Finisher

Operation

Built-in finisher

1

T2S

Tray 2 solenoid

2

T2OM

Paper exit motor

3

SPS

Stopper solenoid

4

SCRS

Roller pressure release solenoid

5

PPS

Rear edge h folding solenoid

6

SCGS

Compiler gate solenoid

7

STTM

Staple rotation motor

8

STUM

Stapler shift motor

9

MM

Main drive motor

10

EVM

Elevator motor

11

STM

Staple motor

12

JRM

Jogger motor rear

13

JFM

Jogger motor front

14

PSM

Pusher motor

Console finisher

1

FFC

Folding clutch

2

FPSM

Puncher side register motor

3

FPNM

Punch motor

4

FLM

Shift  motor

5

FFSM

Stapler motor

6

FSM

Slide motor

7

FRJM

Alignment motor R

8

FFJM

Alignment motor F

9

FAM

Bundle exit motor

10

FPM

Paddle motor

11

FFM

Transport motor

SIMULATION 3-3

FINISHER SENSOR CHECK.

PID           SCID         SCID2         PPD

SCPD          POD          T1PF          T2UP

T2DN          T2PD         STSP          STLS

STNC          STHP         JFHP          JRHP

PSHP          STUHP        STTHP1

STTHP2        DOPD         DSW1          DSW2

24VM          MMLK

SIMULATION 3-2

FINISHER SENSOR CHECK.

FSSS  FJS     FFDSW  FTCS    FFDS 

FSPS  FSUC    FSS    FSTHPS  FSHPS   FLE     FLLLS

FULS  FFE     FFES   FFRHPS  FFHPS   FFPS    FSLS

FBES  FOBHPS  FAS    FRJHPS  FFJHPS  FARHPS  FPHPS

FES

(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)

(FPDSS1)(FPTS)

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

3-6

Adjustment

Used to adjust the stacking capacity of the 
finisher. (Used to adjust the alignment plate 
(jogger) stop position in the finisher paper width 
direction. The adjustment is made by changing the 
alignment plate home position in the paper width 
direction by software.)

Finisher

Operation

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and the 
operation is stopped.
Stops when the operation is terminated.

3-10

Adjustment

Console finisher (AR-FN7) adjustment

Finisher

Operation

Item

Set 

range

Initial 
value

1STEP

1

Saddle binding position 
adjustment

0 - 400

200

0.0707mm

2

Saddle folding position 
adjustment

0 - 400

200

0.0525mm

3

Front alignment position 
adjustment

0 - 20

10

0.367mm

4

Rear alignment position 
adjustment

0 - 20

10

0.367mm

SIMULATION 3-3

FINISHER LOAD TEST. SELECT 1-

AND PRESS START.

2

SIMULATION 3-3

FINISHER LOAD TEST. EXECUTING

.

2

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.

50

SIMULATION 3-6

FINISHER JOGGER ADJUSTMENT. MOVING....

50

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 10

The operating conditions of the sensors and detectors are dis-
played.

The active sensors and detectors are highlighted.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the load.

The operating conditions of the sensors and detectors are dis-
played.

The active sensors and detectors are highlighted.

5

Staple rear one-position 
binding position adjustment

0 - 200

100

0.04374mm

6

Staple front one-position 
binding position adjustment

0 - 200

100

0.04374mm

7

Staple 2-position binding 
center adjustment

0 - 200

100

0.04374mm

8

Staple 2-position binding pitch 
adjustment

0 - 99

50

0.04374mm

9

Punch center adjustment 
(Slide direction)

47 - 53

50

1mm

10 Punch hole position 

adjustment (Paper feed 
direction)

0 - 99

50

0.105mm

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

3-20

Operation test/Check

Used to check the mail bin stacker sensor.

Mail bin stacker

Operation

MPFD1

Tray 1 paper full detection 

MPFD2

Tray 2 paper full detection 

MPFD3

Tray 3 paper full detection 

MPFD4

Tray 4 paper full detection 

MPFD5

Tray 5 paper full detection 

MPFD6

Tray 6 paper full detection 

MPFD7

Tray 7 paper full detection 

MPFD8

Tray 8 paper full detection 

MPID

Interface unit paper entry detection

MPPD1

Paper transport sensor 1

MPPD2

Paper transport sensor 2

MPPD3

Paper transport sensor 3

MPPD4

Paper transport sensor 4

MPPD5

Paper transport sensor 5

M24VM

24V power supply

MDD1

Jam cancel door

MDOPD

Interface unit door

Item

Set 

range

Initial 
value

1STEP

SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10,AND PRESS START.
1.SADDLE POSITION         2.FOLDING POSITION
3.FRONT ADJUST
4.REAR ADJUST             5.STAPLE REAR
6.STAPLE FRONT            7.STAPLE BOTH
8.STAPLE PITCH            9.PUNCH CENTER
10.PUNCH HOLE

1

SIMULATION 3-10

CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.

1.FOLDING POSITION

200

SIMULATION 3-20

MAIL BOX SENSOR CHECK.

MPFD1

 MPFD2  MPFD3  MPFD4  MPFD5  MPFD6  MPFD7

MPFD8  MPID   MPPD1  MPPD2  MPPD3  MPPD4  MPPD5

M24VM  MDD1   MDOPD

3-21

Operation test/Check

Used to check the operations of the mail bin 
stacker loads.

Mail bin stacker

Operation

1

MM

Main motor

2

GSOL1

Gate solenoid 1

3

GSOL2

Gate solenoid 2

4

GSOL3

Gate solenoid 3

5

GSOL4

Gate solenoid 4

6

GSOL5

Gate solenoid 5

7

GSOL6

Gate solenoid 6

8

GSOL7

Gate solenoid 7

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

4-2

Operation test/Check

Used to check the operations of the sensors and 
detectors in the paper feed section (desk paper 
feed/large capacity tray) and the related circuit.

Paper feed

Operation

SIMULATION 3-21
MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7

2

SIMULATION 3-21
MAIL BOX LOAD TEST. EXECUTING....
1.MM

 

2.GSOL1
3.GSOL2
4.GSOL3
5.GSOL4
6.GSOL5
7.GSOL6
8.GSOL7

2

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 11

<Desk>

<LCC>

1.

Select the number corresponding to the target of operation
check with 10-key.

2.

Press [START] key.

The load selected in procedure 1 is operated.

Press [CUSTOM SETTINGS] key to stop the operation of the
load.

<Desk>

<LCC>

DDRS

Desk door sensor

DSPD2

Desk cassette 2 remaining paper quantity sensor

DSPD1

Desk cassette 1 remaining paper quantity sensor

DCSS24

Desk cassette 2 paper rear edge sensor 4

DCSS23

Desk cassette 2 paper rear edge sensor 3

DCSS22

Desk cassette 2 paper rear edge sensor 2

DCSS21

Desk cassette 2 paper rear edge sensor 1

DLUD2

Desk cassette 2 upper limit sensor

DPED2

Desk cassette 2 paper sensor

DPFD3

Desk paper transport sensor 3

DCSS14

Desk cassette 1 paper rear edge sensor 4

DCSS13

Desk cassette 1 paper rear edge sensor 3

DCSS12

Desk cassette 1 paper rear edge sensor 2

DCSS11

Desk cassette 1 paper rear edge sensor 1

DLUD1

Desk cassette 1 upper limit sensor

DPED1

Desk cassette 1 paper sensor

DPFD2

Desk paper transport sensor 2

MCSS4

MP tray size detection 4

MCSS3

MP tray size detection 3

MCSS2

MP tray size detection 2

MCSS1

MP tray size detection 1

MCSPD

MP tray remaining quantity detection 

MCLUD

MP tray upper limit detection

MCPED

MP tray paper empty detection 

DPFD1

MP tray transport detection

TDRS

Tandem side door sensor

TTSD

Tandem tray sensor

TLUD2

Tandem tray 2 upper limit sensor

TLUD1

Tandem tray 1 upper limit sensor

TSPD2

Tandem tray 2 remaining quantity sensor

TSPD1

Tandem tray 1 remaining quantity sensor

TPED2

Tandem tray 2 paper sensor

TPED1

Tandem tray 1 paper sensors

TPFD3

Tandem paper transport sensor 3

TPFD2

Tandem paper transport sensor 2

MCSS4

MP tray size detection 4

MCSS3

MP tray size detection 3

MCSS2

MP tray size detection 23

MCSS1

MP tray size detection 1

MCSPD

MP tray remaining quantity detection 

MCLUD

MP tray upper limit detection 

MCPED

MP tray paper empty detection 

TPFD1

MP tray transport detection 

SIMULATION 4-2
DESK  SENSOR CHECK.
DDRS         DPFD1        DPFD2        DPFD3
MCLUD        DLUD1        DLUD2        MCSPD
DSPD1        DSPD2        MCPED        DPED1
DPED2        MCSS1        MCSS2        MCSS3
MCSS4        DCSS11       DCSS12       DCSS13
DCSS14                    DCSS21       DCSS22
DCSS23       DCSS24

SIMULATION 4-2
LCC SENSOR CHECK.
TDRS        TTSD          TPFD1        TPFD2
TPFD3       MCLUD         TLUD1        TLUD2
MCSPD       TSPD1         TSPD2        MCPED
TPED1       TPED2         MCSS1        MCSS2
MCSS3       MCSS4

4-3

Operation test/Check

Used to check the operations of the loads in the 
paper feed section (desk paper feed/large 
capacity tray) and the related circuit.

Paper feed

Operation

1

DLUM2

Desk lift-up motor 2

2

DLUM1

Desk lift-up motor 1

3

MCLUM

Desk multi lift-up motor

4

DPFCL

Desk paper transport clutch 

5

DPCL2

Desk paper feed clutch 2

6

DPCL1

Desk paper feed clutch 1

7

MCPCL

Desk multi paper feed clutch 

8

DMM

Desk transport motor

1

TLUM2

LCC lift-up motor 2

2

TLUM1

LCC lift-up motor 1

3

MCLUM

LCC multi lift-up motor

4

TPFCL

LCC transport clutch 

5

TPCL2

LCC paper feed clutch 2

6

TPCL1

LCC paper feed clutch 1

7

MCPCL

LCC multi paper feed clutch

8

TMM

LCC transport motor

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.

SIMULATION 4-3

LCC LOAD TEST. SELECT 1- , AND PRESS START.

1.

    2

SIMULATION 4-3

LCC LOAD TEST. EXECUTING....

1.

    2

AR-M351U/M451U, AR-M355U/M455U  SIMULATION  9 - 12

The LCD is changed as shown below. (The contrast changes
every 2sec from the current level to MAX 

→

 MIN 

→

 the current

level. During this period, each LED is lighted.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1 performs ON/OFF operation.

Press [CUSTOM SETTINGS] key to stop the operation of the
load.

The ON/OFF operation of the selected heater lamp is
repeated every 500ms five times.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1 turns ON for 10sec.

Press [CUSTOM SETTINGS] key to stop the operation.

The copy lamp or CIS is turned on for 10sec and turned off.

NOTE: CIS: only when the DSPF is installed.

1) Select the number corresponding to the target of operation

check with 10-key.

2) Press [START] key.

The load selected in procedure 1 operates.

Press [CUSTOM SETTINGS] key to stop the operation.

5-1

Operation test/Check

Used to check the operation of the display, LCD in 
the operation panel, and control circuit.

Operation (Display/Operation key)

Operation

After 6.0sec

Press [CUSTOM SETTINGS] key, 
and the operation is stopped.

5-2

Operation test/Check

Used to check the operation of the heater lamp 
and the control circuit.

Fixing (Fusing)

Operation

1

HL1 (LOWER)

Heater lamp 1 (Lower)

2

HL2 (UPPER)

Heater lamp 2 (Upper)

Press [START] key, and the 
operation is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped.
The operation is repeated the specified 
number of times before stopping.

SIMULATION 5-1

SIMULATION 5-1

SIMULATION 5-2

HEATER LAMP TEST. SELECT 1-2, AND PRESS START.

1.HL1(LOWER)

2.HL2(UPPER)

    2

SIMULATION 5-2

HEATER LAMP TEST. EXECUTING···.

1.HL1(LOWER)

2.HL2(UPPER)

    2

5-3

Operation test/Check

Used to check the operation of the scanner lamp 
and the control circuit.

Optical (Image scanning)

Operation

Press [START] key, and the operation 
is started.

Press [CUSTOM SETTINGS] key, and 
the operation is stopped after 10sec.

6-1

Operation test/Check

Used to check the operation of the paper transport 
system loads and the control circuit.

Paper transport (Discharge/Switchback/Transport)

Operation

1

MSWPR

MSW power relay signal

2

HLPR 

Heater power relay

3

DCPR DC 

power 

relay

4

MM Main 

motor

5

DM

Drum motor

6

POM_FW

Paper exit motor forward rotation

7

POM_RV

Paper exit motor reverse rotation

8

CPFC

Paper feed clutch

9

RRC

Resist roller clutch

10

TRC

Transport roller clutch

11

FGS_FIN

Finisher gate solenoid

12

LUM

Tray 1 lift-up motor

13

TRC_DSK

Desk clutch sync signal

14

PSPS

Separation pawl solenoid

15*1

MCM

MP drive motor control signal

16*1

MCPCL

MP tray paper feed clutch signal

17*1

MCFCL

MP tray transport clutch signal

SIMULATION 5-3

COPY LAMP TEST. SELECT 1-2, AND PRESS START.

1.COPY LAMP

2.CIS

1

SIMULATION 5-3

COPY LAMP TEST. EXECUTING···.

1.COPY LAMP

2.CIS

1