Sharp AR-M351N / AR-M451N (serv.man10) User Manual / Operation Manual ▷ View online
MISFEED REMOVAL
2-18
Misfeed in the transport area, fusing area, and exit area
1
Unlatch the duplex module and slide it to
the left.
the left.
Unlatch the module and
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
2
Remove the misfed paper as shown in the
illustrations below.
illustrations below.
If paper is misfed in the
transport area, turn roller
rotating knob A in the
direction of the arrow to
remove the misfed
paper.
transport area, turn roller
rotating knob A in the
direction of the arrow to
remove the misfed
paper.
o
If paper is misfed in the
fusing area, turn roller
rotating knob B in the
direction of the arrow to
remove the misfed
paper.
fusing area, turn roller
rotating knob B in the
direction of the arrow to
remove the misfed
paper.
If the misfed paper is
inside the fusing area,
turn down the fusing unit
open tab to open the
fusing unit and remove
the misfed paper.
inside the fusing area,
turn down the fusing unit
open tab to open the
fusing unit and remove
the misfed paper.
If paper is misfed in the
exit area, remove it as
shown while taking care
not to tear the paper.
exit area, remove it as
shown while taking care
not to tear the paper.
If the duplex module is
equipped with an exit
tray and paper is misfed
in the exit area, remove
the misfed paper as
shown in the illustration.
equipped with an exit
tray and paper is misfed
in the exit area, remove
the misfed paper as
shown in the illustration.
3
Gently close the duplex module.
If the machine is not
equipped with a duplex
module, close the side
cover.
After closing, confirm
that the misfeed
message is cleared and
the normal display
appears.
equipped with a duplex
module, close the side
cover.
After closing, confirm
that the misfeed
message is cleared and
the normal display
appears.
CAUTION
The fusing unit is hot. Take care in removing paper.
(Do not touch the metal parts.)
(Do not touch the metal parts.)
NOTE
Do not touch or
damage the transfer
roller.
damage the transfer
roller.
Do not touch or
damage the
photoconductive
drum.
damage the
photoconductive
drum.
Roller rotating knob A
Transfer roller
Photoconductive drum
CAUTION
The fusing unit is hot. Take care in removing paper.
(Do not touch any metal parts.)
(Do not touch any metal parts.)
Roller rotating knob B
Fusing unit open tab
Copy_EX.book 18 ページ ２００４年９月２８日 火曜日 午後９時５４分
MISFEED REMOVAL
2-19
2
Misfeed in the duplex module
1
Unlatch the duplex module and slide it to
the left.
the left.
Unlatch the unit and
gently move the module
away from the machine.
gently move the module
away from the machine.
2
If the duplex module has an exit tray,
rotate it up out of the way and open the
cover of the duplex module.
rotate it up out of the way and open the
cover of the duplex module.
If no exit tray is attached,
just open the cover of
the duplex module and
ignore any reference to
the tray in the following
steps.
just open the cover of
the duplex module and
ignore any reference to
the tray in the following
steps.
3
While holding the exit tray up, remove the
misfed paper as shown in the illustrations
below.
misfed paper as shown in the illustrations
below.
If paper is misfed at the
upper part of the duplex
module, gently remove it
while taking care not to
tear the paper.
upper part of the duplex
module, gently remove it
while taking care not to
tear the paper.
If paper is misfed at the
lower part of the duplex
module, gently remove it
while taking care not to
tear the paper.
lower part of the duplex
module, gently remove it
while taking care not to
tear the paper.
4
Close the cover of the duplex module and
lower the exit tray.
lower the exit tray.
5
Gently close the duplex module.
After closing the duplex
module, confirm that the
misfeed message is
cleared and the normal
display appears.
module, confirm that the
misfeed message is
cleared and the normal
display appears.
■
■
■
■ Misfeed in the bypass tray
1
Unlatch the duplex module and slide it to
the left.
the left.
Unlatch the unit and
gently move the module
away from the machine.
gently move the module
away from the machine.
2
Remove the misfed from the bypass tray.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
Gently close the duplex module.
After closing the duplex
module, confirm that the
misfeed message is
cleared and that the
normal display appears.
module, confirm that the
misfeed message is
cleared and that the
normal display appears.
Copy_EX.book 19 ページ ２００４年９月２８日 火曜日 午後９時５４分
MISFEED REMOVAL
2-20
Misfeed in the paper feed area
■
■
■
■ Misfeed in paper tray 1
1
Unlatch the duplex module and slide it to
the left.
the left.
Unlatch the module and
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
2
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
If misfed paper is not found in step 2, pull
out paper tray 1 and remove the misfed
paper.
out paper tray 1 and remove the misfed
paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
4
Gently close the paper tray.
Push the paper tray
back into the machine.
back into the machine.
5
Gently close the duplex module.
If the machine is not
equipped with a duplex
module, close the side
cover.
After closing, confirm
that the misfeed
message is cleared and
the normal display
appears.
equipped with a duplex
module, close the side
cover.
After closing, confirm
that the misfeed
message is cleared and
the normal display
appears.
NOTE
Be sure to follow the misfeed removal sequence. Do not pull the tray out immediately as the misfeed may have
occurred with paper partially fed out of the tray. Open the left cover and see if there is misfed paper first (steps 1
and 2). If you open the tray without checking, the partially fed paper may tear and leave torn pieces in the machine,
increasing the difficulty of removal.
occurred with paper partially fed out of the tray. Open the left cover and see if there is misfed paper first (steps 1
and 2). If you open the tray without checking, the partially fed paper may tear and leave torn pieces in the machine,
increasing the difficulty of removal.
NOTE
The paper may not be extending out far from inside
the machine but must be removed if it is possible to
grasp it. If it is not possible to grasp it, go to the next
step.
the machine but must be removed if it is possible to
grasp it. If it is not possible to grasp it, go to the next
step.
NOTE
If paper drops beyond the rear side of the paper tray
that has been pulled out, remove the paper tray and
then remove the paper. (For removal of the paper
tray, see the illustration below.)
that has been pulled out, remove the paper tray and
then remove the paper. (For removal of the paper
tray, see the illustration below.)
After pulling out the
paper tray until it
stops, gently lift and
pull the tray to remove
it. To reinstall the
paper tray, insert it at
an angle and then
push
paper tray until it
stops, gently lift and
pull the tray to remove
it. To reinstall the
paper tray, insert it at
an angle and then
push
it
into
the
machine.
To remove a paper tray from a stand/paper drawer,
pull the tray out until it stops then rotate it to the left
to disengage it from the stand. When reinstalling it,
place the left rear or the drawer into the slot and
rotate the drawer to the right and into the stand.
pull the tray out until it stops then rotate it to the left
to disengage it from the stand. When reinstalling it,
place the left rear or the drawer into the slot and
rotate the drawer to the right and into the stand.
Installation of trays in the stand/3x500 sheet
paper drawer
paper drawer
The middle and lower trays cannot be installed in the
upper tray position and the upper tray cannot be
installed to the middle and lower tray positions.
(These cannot be pushed into the machine.)
Take care not to install a tray to an improper position
after removing the tray.
upper tray position and the upper tray cannot be
installed to the middle and lower tray positions.
(These cannot be pushed into the machine.)
Take care not to install a tray to an improper position
after removing the tray.
Copy_EX.book 20 ページ ２００４年９月２８日 火曜日 午後９時５４分
MISFEED REMOVAL
2-21
2
■
■
■
■ Misfeed in the multi purpose drawer
1
Unlatch the duplex module and slide it to
the left.
the left.
Unlatch the module and
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
gently move the module
away from the machine.
If the machine is not
equipped with a duplex
module, open the side
cover similarly.
2
Open the left cover of the stand/paper
drawer.
drawer.
Hold the knob and gently
open the cover.
If the machine is not
equipped with a stand/
paper drawer, open the
left cover of the multi
purpose drawer.
open the cover.
If the machine is not
equipped with a stand/
paper drawer, open the
left cover of the multi
purpose drawer.
3
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
4
Close the left cover of the stand/paper
drawer.
drawer.
5
Gently close the duplex unit.
If the machine is not
equipped with a duplex
module, close the side
cover.
After closing, confirm that
the misfeed message has
been cleared and the
normal display appears.
equipped with a duplex
module, close the side
cover.
After closing, confirm that
the misfeed message has
been cleared and the
normal display appears.
6
If misfed paper is not found in step 3, refer to
"Misfeed in paper tray 1" (steps 1 to 5 on the
previous page) to remove the misfed paper.
"Misfeed in paper tray 1" (steps 1 to 5 on the
previous page) to remove the misfed paper.
■
■
■
■ Misfeed in the stand/3 x 500 sheet paper
drawer
For misfeed removal in the upper tray, follow the
procedure of "Misfeed in the multi purpose drawer"
shown to the left to remove the misfed paper.
procedure of "Misfeed in the multi purpose drawer"
shown to the left to remove the misfed paper.
■
■
■
■ Misfeed in the stand/MPD & 2000 sheet
paper drawer
For misfeed removal in the upper tray, follow the
procedure of "Misfeed in the multi purpose drawer"
shown to the left to remove the misfed paper. For
misfeed removal in the lower large capacity tray,
follow the procedure below.
procedure of "Misfeed in the multi purpose drawer"
shown to the left to remove the misfed paper. For
misfeed removal in the lower large capacity tray,
follow the procedure below.
1
Follow steps 1 to 4 of "Misfeed in the multi
purpose drawer" shown to the left.
purpose drawer" shown to the left.
2
If misfed paper is not found in step 1, refer
to "Misfeed in paper tray 1" on the
previous page.
to "Misfeed in paper tray 1" on the
previous page.
3
If misfed paper is not found in steps 1 and
2, pull out the large capacity tray (lower
tray) and remove the misfed paper as
shown in the illustrations below.
2, pull out the large capacity tray (lower
tray) and remove the misfed paper as
shown in the illustrations below.
Raise the paper guide and
remove the misfed paper.
After removing the
misfed paper, be sure to
return the paper guide.
remove the misfed paper.
After removing the
misfed paper, be sure to
return the paper guide.
4
Gently close the large capacity tray.
Push the paper tray all
the way into the
machine.
the way into the
machine.
5
Gently close the duplex module.
If the machine is not equipped with a duplex
module, close the side cover.
After closing, confirm that the misfeed message
has been cleared and the normal display appears.
module, close the side cover.
After closing, confirm that the misfeed message
has been cleared and the normal display appears.
NOTE
The paper may not be extending out far from inside
the machine but must be removed if it is possible to
grasp it. If it is not possible to grasp it, go to the next
step.
the machine but must be removed if it is possible to
grasp it. If it is not possible to grasp it, go to the next
step.
Copy_EX.book 21 ページ ２００４年９月２８日 火曜日 午後９時５４分
Click on the first or last page to see other AR-M351N / AR-M451N (serv.man10) service manuals if exist.