Sharp AR-M351N / AR-M451N (serv.man10) User Manual / Operation Manual ▷ View online
SPECIAL MODES
5-9
5
Tandem copy
Two machines connected to the same network can be used to run a large copy job in parallel.
By dividing the job in half, approximately half the time is required to complete the job.
To use this function, two machines must be connected to your network as network printers. Even if more machines are
connected to the network, this function can only be used to have one other machine share a job.
By dividing the job in half, approximately half the time is required to complete the job.
To use this function, two machines must be connected to your network as network printers. Even if more machines are
connected to the network, this function can only be used to have one other machine share a job.
Server machine and client machine
●In the following explanations, the machine on which
●In the following explanations, the machine on which
the copy job is initially set up and tandem copy
selected is called the server machine. The other
machine that is asked to share the job is called the
client machine.
selected is called the server machine. The other
machine that is asked to share the job is called the
client machine.
●To use the tandem copy function, the tandem
settings must be configured in the key operator
programs. (See page 5-7 of the "Operation manual
(for printer)")
programs. (See page 5-7 of the "Operation manual
(for printer)")
●When configuring the tandem settings in the server
machine, the IP address of the client machine must
be entered. For the port number, it is best to use the
initial setting (50001). Unless you experience
difficulty with this setting, do not change it. The
tandem settings should be configured by your
network administrator. If the server and client
machines will alternate server and client roles, the IP
address of the server machine must also be entered
in the client machine. The same port number can be
set in both machines.
be entered. For the port number, it is best to use the
initial setting (50001). Unless you experience
difficulty with this setting, do not change it. The
tandem settings should be configured by your
network administrator. If the server and client
machines will alternate server and client roles, the IP
address of the server machine must also be entered
in the client machine. The same port number can be
set in both machines.
1
Touch the [TANDEM COPY] key on the
special modes screen.
special modes screen.
The [TANDEM COPY]
key will be highlighted to
indicate that the function
is turned on, and the
tandem copy icon (
key will be highlighted to
indicate that the function
is turned on, and the
tandem copy icon (
)
will appear in the upper
left of the screen.
left of the screen.
2
Touch the [OK] key on the special modes
screen.
screen.
You will return to the
main screen of copy
mode.
main screen of copy
mode.
3
Set the number of copies with the numeric
keys.
keys.
Up to 999 copies can be
set. When the [START]
key is pressed, the
copies will automatically
be divided between the
server and client
machines. If an odd
set. When the [START]
key is pressed, the
copies will automatically
be divided between the
server and client
machines. If an odd
number of copies is set, the server machine will
make the extra set.
make the extra set.
4
Place the original in the document feeder
or on the document glass. (page 4-3)
or on the document glass. (page 4-3)
100 sets of copies
50 sets of copies
50 sets of copies
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
See "General procedure for using special
functions" on page 5-2.
ERASE
OK
1/3
DUAL PAGE
COPY
JOB
BUILD
TANDEM
COPY
RASE
OK
1/3
DUAL PAGE
COPY
JOB
BUILD
TANDEM
COPY
If an incorrect number of copies is set...
Press the clear key and set the correct number of
copies.
Press the clear key and set the correct number of
copies.
Copy_EX.book 9 ページ ２００４年９月２８日 火曜日 午後９時５４分
SPECIAL MODES
5-10
5
Press the [START] key.
NOTES
● To perform tandem copying, the server machine and client machine must meet certain conditions.
● To perform tandem copying, the server machine and client machine must meet certain conditions.
After the [START] key is pressed on the server machine, the server machine verifies that the conditions have
been met. If the conditions have not been met, tandem copying does not begin and "TANDEM OUTPUT IS
NOT ALLOWED. OUTPUT ALL SETS USING MASTER MACHINE?" appears in the display. To have the
server machine make all the copies, touch the [OK] key. To cancel the job, touch the [CANCEL] key.
• As an example, the following conditions must be met when a staple finisher is installed on the server machine
been met. If the conditions have not been met, tandem copying does not begin and "TANDEM OUTPUT IS
NOT ALLOWED. OUTPUT ALL SETS USING MASTER MACHINE?" appears in the display. To have the
server machine make all the copies, touch the [OK] key. To cancel the job, touch the [CANCEL] key.
• As an example, the following conditions must be met when a staple finisher is installed on the server machine
and not on the client machine:
(1) If tandem copying is executed for a two-sided copy job with the number of copies set to 999 and "Non-
(1) If tandem copying is executed for a two-sided copy job with the number of copies set to 999 and "Non-
staple" is selected, tandem copying will take place.
(2) If tandem copying is executed for a two-sided copy job with the number of copies set to 999
and
"Staple" is selected, tandem copying will not take place because the client machine does not have a
finisher.
finisher.
● After the [START] key is pressed, if the client machine cannot print because it is out of paper or other reason,
the server machine will print its half of the job. The other half of the job will be stored in the client machine and
the job will be printed when the client machine is able to print.
the job will be printed when the client machine is able to print.
● If auditing mode is enabled on both the server and client machines, the same account number must be entered
on both machines.
● If auditing mode is enabled on the client machine but not on the server machine, tandem copying cannot be
performed.
To cancel the tandem copy function, touch the
[TANDEM COPY] key on the special modes screen
(step 2). The highlighted display will be cancelled.
[TANDEM COPY] key on the special modes screen
(step 2). The highlighted display will be cancelled.
Copy_EX.book 10 ページ ２００４年９月２８日 火曜日 午後９時５４分
SPECIAL MODES
5-11
5
Covers/inserts
A different type of paper can be inserted in positions corresponding to front and back covers of a copy job when the
automatic document feeder is used. A different type of paper can also be automatically added as an insert at
specified pages.
● Covers/inserts can be disabled in the key operator programs (page 11 of the key operator's guide).
automatic document feeder is used. A different type of paper can also be automatically added as an insert at
specified pages.
● Covers/inserts can be disabled in the key operator programs (page 11 of the key operator's guide).
Example of adding covers
Example of adding covers and inserts
Example of adding inserts
About the explanations of covers and
inserts
inserts
There are various ways of using covers and inserts.
To keep the explanations simple, covers and
inserts are explained separately. The procedure for
inserting covers is explained on page 5-12. The
procedure for adding inserts is explained on page 5-
13. After reading these explanations, see the
examples of using covers and inserts on pages 5-
16 to 5-21.
To keep the explanations simple, covers and
inserts are explained separately. The procedure for
inserting covers is explained on page 5-12. The
procedure for adding inserts is explained on page 5-
13. After reading these explanations, see the
examples of using covers and inserts on pages 5-
16 to 5-21.
■
■
■
■ Preparations for using covers and inserts
● Load the cover/insert paper in the tray before using the cover/insert function.
● Use the same size of paper for the covers/inserts as for the copies. (For the procedures for loading paper, see
● Use the same size of paper for the covers/inserts as for the copies. (For the procedures for loading paper, see
pages 2-2 to 2-7.)
● Before selecting the cover/insert function, place the originals in the document feeder, select one-sided or two-
sided copying, and select the number of copies and any other desired copy settings as explained on pages
4-7 to 4-10. When these settings have been completed, perform the procedure to select covers/inserts on the
following page.
4-7 to 4-10. When these settings have been completed, perform the procedure to select covers/inserts on the
following page.
● The original must be scanned from the document feeder. The document glass cannot be used.
● Up to 100 covers/inserts can be inserted. Two covers/inserts cannot be inserted between the same pages.
● Pamphlet copying cannot be used in combination with covers/inserts.
● When performing two-sided copying of two-sided originals, an insert cannot be added between the front and
● Up to 100 covers/inserts can be inserted. Two covers/inserts cannot be inserted between the same pages.
● Pamphlet copying cannot be used in combination with covers/inserts.
● When performing two-sided copying of two-sided originals, an insert cannot be added between the front and
back sides of an original page.
Front cover
Back cover
Originals
Inserts
Front
cover
cover
Back
cover
cover
Originals
Originals
Inserts
Copy_EX.book 11 ページ ２００４年９月２８日 火曜日 午後９時５４分
SPECIAL MODES
5-12
■
■
■
■ Procedure for inserting front and back cover paper
The paper for the front cover is called the front cover paper ("FRONT COVER" in the touch panel). The paper
for the back cover is called the back cover paper ("BACK COVER" in the touch panel).
●Examples of insertion methods for the front and back cover paper are given on pages 5-17 to 5-20.
for the back cover is called the back cover paper ("BACK COVER" in the touch panel).
●Examples of insertion methods for the front and back cover paper are given on pages 5-17 to 5-20.
1
Touch the [COVERS/INSERTS] key in the
special modes screen (2nd screen).
special modes screen (2nd screen).
2
Touch the [PAPER TRAY SETTINGS] key.
3
Select the tray used for the front cover
paper.
paper.
(1)The tray name (tray position) selected for the
front cover paper and the paper size and type
are shown in (X). If the tray in which you
loaded paper for the front cover is shown, touch
the [OK] key. You will return to the screen of
step 2.
are shown in (X). If the tray in which you
loaded paper for the front cover is shown, touch
the [OK] key. You will return to the screen of
step 2.
(2)If the correct tray for the cover sheet paper
does not appear in (X), touch the (Y) key. The
tray selection screen will appear. Select the
tray in which you loaded paper for the front
cover. You will return to the screen of above.
tray selection screen will appear. Select the
tray in which you loaded paper for the front
cover. You will return to the screen of above.
4
Touch the [FRONT COVER] key in the
screen of step 2.
screen of step 2.
5
Set the insertion conditions for the front
cover paper.
cover paper.
(1) Select whether or not the front cover paper is to be
copied on with the (X) keys ([YES] or [NO]).
(2) Select whether one-sided copying or two-sided
copying is to be performed on the front cover
paper with the (Y) keys. This selection is only
possible when the [YES] key of (X) has been
selected. (The one-sided/two-sided selection
made here only applies to the front cover paper.
When the back cover paper is selected, the
selection only applies to the back cover paper.)
paper with the (Y) keys. This selection is only
possible when the [YES] key of (X) has been
selected. (The one-sided/two-sided selection
made here only applies to the front cover paper.
When the back cover paper is selected, the
selection only applies to the back cover paper.)
(3)The (Z) key shows the tray selected for the front
cover paper in step 3 and the paper size and
type.
type.
6
Touch the [OK] key in the screen of step 5.
You will return to the screen of step 2.
You will return to the screen of step 2.
When you return to the screen of step 2, the
[FRONT COVER] key will be highlighted.
[FRONT COVER] key will be highlighted.
7
To insert back cover paper, repeat steps 2
through 6, using the [BACK COVER] key
instead of the [FRONT COVER] key.
through 6, using the [BACK COVER] key
instead of the [FRONT COVER] key.
8
Touch the [PAGE LAYOUT] key in the
screen of step 7 to display a list of the
selected settings (page 5-15).
To exit the cover/insert settings, touch the
upper [OK] key in the screen of step 7.
screen of step 7 to display a list of the
selected settings (page 5-15).
To exit the cover/insert settings, touch the
upper [OK] key in the screen of step 7.
9
Press the [START] key.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
See "General procedure for using special
functions" on page 5-2.
SPECIAL MODES
COVERS/INSERTS
TRANSPARENCY
INSERTS
CARD SHOT
BOOK COPY
FRONT COVER
BACK COVER
INSERTION
TYPE A SETTING
PAPER TRAY
SETTINGS
PAGE LAYOUT
CANCEL
OK
INSERTION
SETTINGS
COVERS/INSERTS
INSERTION
TYPE B SETTING
A4
PLAIN
PAPER TRAY SETTINGS
FRONT COVER
TRAY2
TRAY2
TRAY2
TRAY2
TRAY2
BACK COVER
INSERTION
TYPE A
INSERTION
TYPE B
OK
A4
PLAIN
A4
PLAIN
A4
PLAIN
(X)
(Y)
To cancel covers/inserts settings...
Touch the [CANCEL] key in the screen of step 2.
Touch the [CANCEL] key in the screen of step 2.
PLEASE SET UP A FRONT COVER.
FRONT COVER SETTING
PRINT ON FRONT COVER
YES
NO
1-SIDED
2-SIDED
0
OK
CANCEL
PAPER TRAY
TRAY2
A4
PLAIN
(X)
(Y)
(Z)
PLEASE SET UP COVERS/INSERTS.
SPECIAL MODES
COVERS/INSERTS
FRONT COVER
INSERTION
TYPE A SETTINGS
PAPER TRAY
SETTINGS
PAGE LAYOUT
INSERTION
SETTINGS
INSERTION
TYPE B SETTINGS
BACK COVER
0
OK
OK
CANCEL
Copy_EX.book 12 ページ ２００４年９月２８日 火曜日 午後９時５４分
Click on the first or last page to see other AR-M351N / AR-M451N (serv.man10) service manuals if exist.