DOWNLOAD Sharp AR-M35 / AR-M450 (serv.man7) Service Manual ↓ Size: 642.38 KB | Pages: 40 in PDF or view online for FREE

 

 

 

33 

 

 

 

There are two methods of upgrading the ARNC5J Network card: 

• 

SCVerup Utility 

• 

From DOS using FTP

SCVerup Utility is available from the Sharp Electronics Technical Web site. After starting the SCVerup utility from 
the list of devices, highlight the machine or machines you wish to upgrade. 

 

Click on the “Browse” button and select the firmware file, 

 

Click on the upload button, wait for the firmware upload to complete. 

For Windows NT both TCP/IP & IPX protocols need to be running to support SCVERUP.  If only TCP/IP protocol is 
running, use ftp. 

 

1.  

Go to MS-DOS prompt 

2.  

Change directory to that where binary file resides 

3.  

Enter ftp command   

 

“ftp” 

4. 

From ftp prompt enter   

“open IP address” 

5. 

For username key 

 

 

admin 

6. 

For password key 

 

 

Sharp 

7. 

At prompt key   

 

“bin” 

8. 

Then send binary file 

 

“put filename.bin” 

9. 

When completed type    

“bye” 

10. 

Power cycle the copier 

 

 

 

 

34 

 

 

 

V4.10 V1.08  V2.12 V2.00 Previously, the machine became inoperative when printing a 

mixed document of envelope, postcard and regular sized paper as 
the machine requested for postcard/envelope when printing 
regular sized paper.  This failure is fixed in this version. Previously, 
the machine did not recover from auto-shut off mode.  This failure 
is fixed in this version. The message to say not to turn off the 
power at the time of paper jamming is added. Previously, the pop-
up message “out-of paper” appeared from S-MON when 
recovering from shut-off mode.  This failure is fixed in this version.  

V5.09 V2.01  V3.01 V3.02 AR-FN7 “High speed stacking mode” is added to Key Operator 

Program previously, the machine locked up if starting to use the 
machine right after clearing a DF-jam.  This failure is fixed in this 
version. Previously, a paper jam between the ADU and the main 
unit could not be cleared without opening/closing the left cover 
twice.  This failure is fixed in this version. Access from the web 
page on the Image Send Screen is made possible by a fix. A 
change is made to delete an email destination after sending e-mail 
if the e-mail destination is highlighted but the “Enable Hyperlink to 
FTP server to be e-mailed” check box is unchecked. 

V6.06 V2.01A V3.04 V4.00 A change is made for compatibility with AR-PF1. Sim.46-26 is 

added. (0 = Pattern matching function ON 1= Pattern matching 
function OFF). 

V6.06 V2.01A V3.06 V4.00 The message “Copying” was indicated and the machine hung up. 

This failure is corrected. The default value of Sim.46-26 (Pattern 
Matching Function when the fax data is sent.) the value is changed 
to ‘0’ (the pattern matching function is available). 

V8.12 V2.01B V5.00 V5.00 Image Send function is improved and the following function is 

added in order to improve the operation. The file transmission 
function in TIFF format is added. (It is possible for the user to 
select this function when the checkbox is ticked.) If the checkbox 
is off when the receiver on FTP is selected, the receiver selected 
when submitted can be cleared. The detailed information about 
the error code is mentioned in Help on Web page. The resolution 
(dpi) is indicated in Help on Web page. The file format can be 
selected every time the image is sent. The rotate-sorting function 
setting is available in Key OP (Checkbox On/Off). The font list 
printing function is added on AR-PF1. The support for binary mode 
is added. When the NC5J is installed, CE-00 trouble is 
experienced.  This failure is eliminated. (It is possible to reduce the 
CE-00 trouble if SW80-8 of Sim.66-1 is set as “1”.) The number of 
pages with memory full in Mass Original mode (special function) 
did not match to the number of pages with memory full in. 

V9.07 V3.02  V6.04 V5.02 The maintenance cycle setting was changed as follows: DEFAULT 

(50K) / 5K / 10K / 25K / 50K / 80K / FREE. Sim26-38 is added for 
MFP model. The machine does not stop if the number of copies 
reaches to the setting for the maintenance cycle + 10%.1 (PRINT 
STOP): The machine stops if the number of copies reaches to the 
setting for the maintenance cycle +10%. 

 

 

 

35 

 

 

 

1) Added [LINE THICKNESS] to the Default settings of 
the printer condition settings 
(2) Added [EXTRA PRINT MODE] to the Default 
settings of the printer condition settings 
(3) Added [DISABLING OF BYPASS PRINTING] to key 
operator programs 
(4) Beep setting 
(5) Modified the Initial resolution setting screen of the 
Operation settings for fax/image transmission (for the 
network scanner setting) 
(6) Modified the default file format setting for fax/image 
transmission (for the network scanner setting) 
(7) 180-Degree image rotation with custom-size paper 
(8) Changed the OUTPUTTRAY  SETTINGS of INITIAL 
STATUS SETTINGS for copy mode. 
(9) Changed the process when exceeding staple 
capacity for saddle stitching 
(10) The image location in the self-printing 70 for the 
simulation and the dialog mode was improved. (Except 
AR-P350/P450) 
(11) If the amount of paper exceeds the capacity before 
printing in saddle stitch B mode, the job stops. 
12) If the job was stopped/resumed after several copies 
in simplex/staple mode, the machine stopped because 
the machine understood the stapler was full. This was 
corrected. 
(13) ”7: 100K” was added for a value of Sim21-1 
Maintenance Cycle setting. 
(14) Control level on outside counter when double-
counted in duplex printing mode was improved. (Except 
AR-P350/P450) 

MFPA.08.SFU 

Main Boot PCU 

Scan 

VmA.08 Vm4.00 V7.02  V5.06 

This firmware version will upgrade Main, Boot, Scan & PCU at 
the same time. It includes the above versions of firmware and 
is downloaded in the same way using Fcopy. 

June01 

 

 

 

 

36 

 

 

V4.10 V2.12 Previously, the machine did not recover from auto-shut off mode.  This 

failure is fixed in this version. The detection of Empty/Not empty/Full is 
added to the saddle stitch tray status when using S-MON/PAU. 

V5.09 V3.01 AR-FN7 “High speed stacking mode” is added to Key Operator Program. 

Previously, a paper jam between the ADU and the main unit could not be 
cleared without opening/closing the left cover twice.  This failure is fixed 
in this version.  

V6.06 V3.04 A change is made for compatibility with AR-PF1.  

V6.06 V3.06 The message “Copying” was indicated and the machine hung up. This 

failure is corrected. The default value of Sim.46-26 (Pattern Matching 
Function when the fax data is sent.) the value is changed to ‘0’ (the 
pattern matching function is available). 

V8.02 V5.00 The rotate-sorting function setting is available in Key OP (Checkbox 

On/Off). The font list printing function is added on AR-PF1. The support 
for binary mode is added. 

V9.07 V6.04 It is possible to change the maintenance cycle setting in “MNT CYCLE 

SET UP” in the dialogue.  However, Please be sure to select “No” for the 
“LIFE OVER SETTING” in the dialogue. 

Ve.08 V7.02 1) Added [LINE THICKNESS] to the Default settings of the printer 

condition settings 
2) Added [EXTRA PRINT MODE] to the Default settings of the printer 
condition settings 
3) Added [DISABLING OF BYPASS PRINTING] to key operator 
programs 
4) Beep setting 
5) Changed the process when exceeding staple capacity for saddle 
stitching 
6) If the amount of paper exceeds the capacity before printing in saddle 
stitch B mode, the job stops. 
7) ”7: 100K” was added for a value of Sim21-1 Maintenance Cycle 
setting.