Sharp AR-M35 / AR-M450 (serv.man7) Handy Guide ▷ View online
Routine Maintenance
Version 2.0
Issue 01/02
13
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
AR-M350/450
SIMULATION DATA
Perform Sim.22-06
Simulation Data Print
MAINTENANCE COMPLETED
Perform Sim. 24-04
Maintenance Counter Reset
Perform Sim.21-01
Maintenance Cycle Check
DEVELOPER REPLACEMENT
Perform Sim. 24-05
Dev Counter Reset
Perform Sim. 25-02
Developer Level Setting
DRUM REPLACEMENT
Perform Sim. 24-07
Drum Membrane Counter Reset
COPY QUALITY
Perform Sim. 46-02
Copy Quality Adjustment (Copy Mode)
SIMULATION DATA
Perform Sim.22-06
Simulation Data Print
Machine Settings & Adjustments
Version 2.0
Issue 01/02
14
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
AR-M350/450
Section
Adjustment Item
Adjustment
Procedure
Procedure
Process
1
Developer doctor gap
0.45mm
2
MG roller main pole position
54.2mm
3
Dev bias voltage
Sim 8-1
4
Main charger grid voltage
Sim 8-2
5
Transfer charge voltage
Sim 8-6
8
Toner concentration
Sim 25-2
Laser scanner
1
Horizontal image distortion
LSU lever adjustment
2
Print off centre
Sim 50-10
3
Laser power setting
Sim 61-20
Scanner
1
Vertical image distortion balance
Copy lamp unit installing position
2
Vertical image distortion balance
No2/3 mirror base installing position
3
Vertical image distortion
Winding pulley position
4
Horizontal image distortion
F rail height adjust
5
Main scan magnification ratio
CCD unit position
6
Main scan magnification ratio
Sim 48-1
7
Shading plate correction
Sim 46-17
8
Scanning image position
Sim 50-2
9
Original off centre
Sim 50-12
Copy Density
1
Copy mode
Sim 46
Paper Feed
1
Manual bypass detection level
Sim 40-2
2
Paper size setting
Paper Transport
1
Separation Pawl Timing
Sim 51-1
2
Resist Roller Buckle
Sim 51-2
Section
Adjustment Item
Adjustment
Procedure
Others
1
Original size sensor detection level
Sim 41-1 / 41-2
2
Waste toner full detection
3
Touch panel
Sim 65-1
4
Key touch sound volume
Sound volume adjustment
DSPF
1
Hinge height
Table clearance
2
Open/Close sensor position
Sim 2-2
Test Simulation
Version 2.0
Issue 01/02
15
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
AR-M350/450
To enter simulation =
P * C *
Test
Command
Sub Code
Default
Setting
Setting
Description
1
--
Checks optical system.
01
Scanner test
02
Scanner sensor check
2
--
Checks Document Feeder ageing.
01
DF ageing test.
02
DF sensor check
03
DF output check (motor, clutch, solenoid)
3
--
Checks Finisher activation.
02
Finisher sensor check
03
Finisher output check (motor, clutch, solenoid)
06
Finisher jogger adjustment
10
Console Finisher adjustment (AR-FN7)
20
Mail bin stacker sensor check
21
Mail bin stacker load test
4
--
Checks Desk/LCT activation
02
Desk/LCT sensor check
03
Desk/LCT o/put check (motor, clutch, solenoid)
5
--
Checks the lighting of lamps.
01
LCD/LED
test
02
Heater lamp check
03
Copy lamp check
6
--
Checks paper feed component activation
01
Paper feed o/put check (motor clutch solenoid)
02
Fan motor activation
7
--
Checks paper feed ageing
01
Paper feed ageing test setting
06
Interval ageing cycle timer set up
08
Warm up time display setting
8
--
Checks process voltages output.
01
Developer bias setting and output
02
MHV/Grid setting and output
06
THV check and adjust ( transfer).
17
THV setting and output
9
--
Checks ADU activation.
01
ADU output check (motor, clutch, solenoid)
02
ADU sensor check
Test Simulation
Version 2.0
Issue 01/02
16
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
AR-M350/450
Test
Command
Sub Code
Default
Setting
Setting
Description
10
--
Toner motor activation
14
--
Trouble cancel U1/LOC/U2/PF troubles).
15
--
U4-09/20/21/22 LCC trouble cancel
16
--
U2 trouble cancel
17
--
Cancel copy inhibition by host computer during self diag PF
21
01
Maintenance cycle setting
22
--
Counter information displays
01
Counter data display
02
Jam/trouble counter display
03
Jam history data display
04
Trouble history data display
05
ROM version display
06
Data print mode
07
Key operator code display
08
Original/stapler counter display
09
Paper feed counter display
10
Machine system display
12
DF jam history display
13
Process Cartridge Data
19
Scanner mode counter
24
--
Clears special counters
01
Jam/trouble counter clear
02
Paper feed counter clear
03
Original/stapler counter clear
04
Maintenance counter clear
05
Developer counter clear
06
Copy counter clear
07
Drum correction counter clear
09
Printer/other counter clear
10
Fax mode counter clear
11
Reset developer time counter
15
Scanner counter clear
25
01
Checks the activation of main motor drive unit
26 --
Settings
03
Auditor set up
05
2
Total/Maintenance counter set up
06
Destination set up
10
Network scanner trial mode
26
18
Used to set toner save operations
30
CE mark setting
35
0
Trouble memory mode setting
41
Used to disable/enable auto magnification
50
Enable /disable white paper count -up
27
Communications set up
01
To Communications specifications
Sets machine tag number
30
--
Main body sensors
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man7) service manuals if exist.