Sharp AR-M35 / AR-M450 (serv.man7) Handy Guide ▷ View online
Test Simulation
Version 2.0
Issue 01/02
21
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
PCU Self Print
This mode is used to print by using only the PCU data and firmware without using the print controller. This enables
better fault diagnosis by isolating the PCU from the controller.
Execution Procedure
1.
Remove the print controller and the rear panel
2.
Short CN22 on the PCU PWB
3.
Enter diag mode (Menu/OK power on). If the power is already on
reset the PCU by pressing SW1. Press the Menu/OK keys together.
reset the PCU by pressing SW1. Press the Menu/OK keys together.
4.
The machine is now in diag mode
5.
Press the Menu key to select self print mode
6.
Set the self-print pattern from 1-40 and execute.
Caution Do not try to select other than self-print patterns 1-40
Jam Codes
Version 2.0
Issue 01/02
22
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
Jam Codes
Version 2.0
Issue 01/02
23
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
Error Codes
Version 2.0
Issue 01/02
24
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS SUPPORT
TECHNICAL SERVICES GROUP
Sub
Content of trouble
Code
Sub
Content of trouble
C1 00
MC trouble
00
Toner control sensor open
C2 00
TC Trouble
02
Toner under-toned to early
10
CIS Shading trouble (Black correction)
04
Improper cartridge ( life cycle error)
11
CIS Shading trouble (White correction)
05
CRUM error
E6
14
Abnormal harness installation to CIS
F2
39
Process thermistor trouble
01
Picture Memory Trouble (ICU ASIC)
12
Machine No1 tray lift up trouble
02
Laser trouble
F3
22
Multi purpose tray lift up trouble
03
HDD trouble
00
ICU - Fax communication trouble
06
Decode error trouble
01
Fax expansion flash abnormality
10
CCD Shading trouble (Black correction)
F6
04
Fax modem operation abnormality
11
CCD Shading trouble (White correction)
F7 01
Fax board EEPROM read/write error
13
CCD light quantity check error
00
Thermistor open (HL1) fuser not installed
14
CCD ASIC communication error
H2
01
Thermistor open (HL2) fuser not installed
50
LSU connection trouble
00
Heat roller high temperature detection (HL1)
80
ICU - scanner communication trouble
H3
01
Heat roller high temperature detection (HL2)
E7
90
PCU PWB Communication trouble
00
Heat roller low temperature detection (HL1)
00
AR-FN6 communication trouble
H4
01
Heat roller low temperature detection (HL2)
08
AR-FN6 staple shift motor trouble
H5 01
5 continuous POD not-reaching JAM detection
10
AR-FN6 staple unit operation trouble
L1 00
Scanner feed trouble
11
AR-FN6 bundle exit motor trouble
L3 00
Scanner return trouble
15
AR-FN6 lift motor trouble
01
Main motor lock detection
19
AR-FN6 front alignment motor trouble
L4
02
Drum motor lock detection
20
AR-FN6 rear alignment motor trouble
L6 10
Polygon motor lock detection
80
AR-FN6 24V Trouble
01
No full-wave signal
F1
87
AR-FN6 staple rotation motor trouble
L8
02
Full-wave signal width abnormality
00
AR-MS1 communication trouble
01
Fax battery abnormality
02
AR-MS1 transport motor abnormality
U1
02
RTC read abnormality
12
AR-MS1 gate trouble
00
Controller EEPROM read/write error
F1
80
AR-MS1 24V power abnormality
11
Counter check sum error
03
AR-FN7 paddle motor trouble
12
Adjustment check sum error
06
AR-FN7 slide motor trouble
80
Scanner EEPROM read/write error
10
AR-FN7 staple motor trouble
81
Scanner memory check sum error
11
AR-FN7 bundle exit motor trouble
90
PCU EEPROM read/write error
15
AR-FN7 lift motor trouble
U2
91
PCU memory check sum error
19
AR-FN7 front alignment motor trouble
U7 OO
RIC communication trouble
20
AR-FN7 rear alignment motor trouble
EL
Auto developer adjustment trouble - Overtone
30
AR-FN7 communication trouble
EE
EU
Auto developer adjustment trouble - Undertone
31
AR-FN7 fold sensor trouble
PF RIC copy inhibit command reception
32
AR-FN7- punch unit communication trouble
33
AR-FN7 punch side registration motor error
34
AR-FN7 punch motor trouble
35
AR-FN7 side registration sensor trouble
36
AR-FN7 punch timing sensor trouble
37
AR-FN7 back up RAM trouble
38
AR-FN7 punch back up RAM trouble
F1
81
AR-FN7 transport motor abnormality
Click on the first or last page to see other AR-M35 / AR-M450 (serv.man7) service manuals if exist.