Sharp AR-M256 (serv.man18) User Manual / Operation Manual ▷ View online
71
TROUBLESHOOTING AND MAINTENANCE
5
MISFEED IN THE UPPER EXIT AREA
(when a job separator tray kit or finisher (AR-FN5A) is installed)
(when a job separator tray kit or finisher (AR-FN5A) is installed)
If a job separator tray kit or a finisher is installed, a misfeed may occur in the upper exit area.
1
Open the upper right side cover.
2
Gently pull the misfed paper out.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
3
Close the upper right side cover.
Make sure that the misfeed message is cleared.
MISFEED IN AN OUTPUT TRAY
(when a finisher (AR-FN5A) is installed)
(when a finisher (AR-FN5A) is installed)
1
Grasp the handle of the stapler
compiler cover and pull to open the
cover.
compiler cover and pull to open the
cover.
2
Remove any misfed paper from the
transport area.
transport area.
A MISFEED HAS OCCURRED.
INFORMATION
ar_m318_uk_cpy.book 71 ページ 2007年1月15日 月曜日 午前11時36分
72
TROUBLESHOOTING AND MAINTENANCE
3
If staple sort copying is being
performed, open the paper guide and
remove any misfed paper from the
stapler compiler.
performed, open the paper guide and
remove any misfed paper from the
stapler compiler.
4
Close the stapler compiler cover.
5
If the offset tray is being used, remove
any misfed paper from the offset tray.
any misfed paper from the offset tray.
6
If the top tray is being used, open the
top cover, remove any misfed paper,
and close the top cover.
top cover, remove any misfed paper,
and close the top cover.
Make sure that the
misfeed message is
cleared.
misfeed message is
cleared.
ar_m318_uk_cpy.book 72 ページ 2007年1月15日 月曜日 午前11時36分
73
5
REPLACING THE TONER CARTRIDGE
To check how much toner remains in the toner cartridge (p.75), hold down the [COPY] key. The amount of toner
remaining will appear in the display. When less than 25% of the toner remains, obtain a new toner cartridge as soon
as possible. When "TONER SUPPLY IS LOW." appears in the display, be sure to have a new cartridge on hand for
replacement at any time as little toner remains. When "CHANGE THE TONER CARTRIDGE." appears in the touch
panel, the toner cartridge must be replaced. Follow these steps to replace the cartridge.
remaining will appear in the display. When less than 25% of the toner remains, obtain a new toner cartridge as soon
as possible. When "TONER SUPPLY IS LOW." appears in the display, be sure to have a new cartridge on hand for
replacement at any time as little toner remains. When "CHANGE THE TONER CARTRIDGE." appears in the touch
panel, the toner cartridge must be replaced. Follow these steps to replace the cartridge.
1
Press gently on both sides of the front
cover and pull it open.
cover and pull it open.
2
Pull the toner cartridge out while
pressing the lock release lever.
pressing the lock release lever.
When pulling out the
toner cartridge, place
your other hand on the
green part of the
cartridge.
toner cartridge, place
your other hand on the
green part of the
cartridge.
3
Remove the new toner cartridge from
the bag. Grasp both ends of the
cartridge and shake it horizontally
about 20 times. After shaking the
cartridge, remove the tape.
the bag. Grasp both ends of the
cartridge and shake it horizontally
about 20 times. After shaking the
cartridge, remove the tape.
Grasp the hand grip to
hold the cartridge. Do not
hold the cartridge by the
shutter. Be sure to only
shake the cartridge
before the tape is
removed.
hold the cartridge. Do not
hold the cartridge by the
shutter. Be sure to only
shake the cartridge
before the tape is
removed.
4
While pushing the lock release lever,
gently insert the toner cartridge along
the guides until it clicks into place.
gently insert the toner cartridge along
the guides until it clicks into place.
5
Remove the tape from the shutter. Pull
the shutter out of the toner cartridge
as shown in the illustration.
the shutter out of the toner cartridge
as shown in the illustration.
Discard the shutter.
6
Close the front cover.
• Do not throw the toner cartridge into a fire. Toner may fly and cause burns.
• Store toner cartridges out of the reach of small children.
• Store toner cartridges out of the reach of small children.
When running long copy jobs or copying originals with many areas of solid black, "TONER REPLENISHMENT IN
PROGRESS." may appear in the touch panel and copying may stop even though the cartridge still has toner.
When this occurs, the toner is being replenished. Replenishment will last about two minutes. When the [START]
key (
PROGRESS." may appear in the touch panel and copying may stop even though the cartridge still has toner.
When this occurs, the toner is being replenished. Replenishment will last about two minutes. When the [START]
key (
) illuminates, press the [START] key (
) to resume copying.
Caution
Note
• After removing the toner cartridge, do not
shake it or tap it. Doing so may cause
toner to leak from the cartridge. Put the
old cartridge immediately in the bag
provided with the new cartridge.
toner to leak from the cartridge. Put the
old cartridge immediately in the bag
provided with the new cartridge.
• Dispose of the old toner cartridge in
accordance with local regulations.
Handle
Toner cartridge
lock release lever
lock release lever
Note
Tape
Shutter
About 20 times
If dirt or dust adheres to the toner cartridge,
remove it before installing the cartridge.
remove it before installing the cartridge.
Note
05.fm 73 ページ 2007年1月15日 月曜日 午後12時55分
74
STAPLE CARTRIDGE REPLACEMENT
(when the finisher (AR-FN5A) is installed)
When the message "ADD STAPLES." appears, replace the staple cartridge as follows:
1
Open the stapler cover.
2
Grasp the green portion of the staple
box and remove the staple box from
the stapler.
box and remove the staple box from
the stapler.
3
Remove the staple cartridge from
inside the staple box.
inside the staple box.
4
Insert the new staple cartridge into the
box until it clicks into place.
box until it clicks into place.
Insert the new cartridge
by aligning the arrows on
the cartridge with those
on the box.
Check that the cartridge
has locked into place by
pulling it slightly.
by aligning the arrows on
the cartridge with those
on the box.
Check that the cartridge
has locked into place by
pulling it slightly.
5
Remove the tape from the cartridge.
6
Insert the staple box into the stapler
unit until it clicks into place.
unit until it clicks into place.
7
Close the stapler cover.
ar_m318_uk_cpy.book 74 ページ 2007年1月15日 月曜日 午前11時36分
Click on the first or last page to see other AR-M256 (serv.man18) service manuals if exist.