Sharp AR-M165-207 (serv.man17) Service Manual ▷ View online
AR-M207 M165 M162 DISASSEMBLY AND ASSEMBLY 10-5
Assembly: Put the fusing harness (A) on the heater lamp (B) as shown
in the figure and fix them together.<R>Place the fusing
harness inside the rib (C).
harness inside the rib (C).
E. Upper heat roller
Disassembly:
There are three pawls on the fusing cover. Remove the
screws and slide the fusing cover to the right to remove.
The heater lamp is fixed on the fusing cover with a
screw. Slide the fusing cover to the front and remove the
screw. Slide the fusing cover to the front and remove the
screw, then remove the heater lamp.
F. Separation pawl
(A)
(B)
(C)
(1)
(3)
(4)
(2)
(2)
(1)
(3)
(1)
(2)
(1)
(1)
(2)
Grease(JFE552)
Floil(GU2)
(2)
(2)
(3)
(3)
(1)
[10]DISASSEMBLY.fm 5 ページ ２００４年１１月１２日 金曜日 午後２時１７分
AR-M207 M165 M162 DISASSEMBLY AND ASSEMBLY 10-6
G. Lower heat roller
Assembly:
When installing the paper guide (3) before fusing, fix the
paper guide fixing plate with screws temporarily so that the
paper guide fixing plate (2) is in contact with the frame
bottom under fusing (A). Fit the mark (B) on the fusing front
bottom under fusing (A). Fit the mark (B) on the fusing front
paper guide (3) with the top of the rib (C), and tighten the
screw securely.
H. Separation pawl
I. Cleaning pad
How to clean paper dust on the fuser cleaning felt.
Remove Fusing rear paper guide from Fusing unit during every periodic
maintenance (50K) and clean the collected paper dust using a ruler or
maintenance (50K) and clean the collected paper dust using a ruler or
other straight-edge device.
Replace the cleaning felt at 150k or earlier if damaged.
4. Paper exit section
A. Ozone filter
(1)
(1)
(3)
(2)
(2)
(A)
(4)
(B)
(C)
(B)
(C)
Grease(JFE552)
No.
Content
A
Ozone filter
B
Cooling fan
C
Paper exit unit
D
Transport roller
E
Paper exit roller
F
Paper exit interface P.W.B.
G
Paper exit sensor / duplex sensor
Fusing rear paper guide
Paper dust
Cleaning
felt AS
felt AS
(1)
(1)
(2)
(1)
(1)
(1)
(1)
(2)
(2)
[10]DISASSEMBLY.fm 6 ページ ２００４年１１月１２日 金曜日 午後２時１７分
AR-M207 M165 M162 DISASSEMBLY AND ASSEMBLY 10-7
B. Cooling fan
C. Paper exit unit
Duplex model
Simplex model
(1)
(1)
(2)
(2)
(1)
(1)
(1)
(2)
(1)
(1)
(3)
(3)
(2)
(4)
(1)
(2)
(2)
(3)
(1)
(2)
(3)
(3)
(3)
(3)
(3)
(4)
(1)
(2)
(3)
(3)
(1)
(3)
(2)
(3)
(1)
(4)
(5)
(1)
(1)
(2)
(4)
(6)
(5)
[10]DISASSEMBLY.fm 7 ページ ２００４年１１月１２日 金曜日 午後２時１７分
AR-M207 M165 M162 DISASSEMBLY AND ASSEMBLY 10-8
D. Transport roller
E. Paper exit roller
Assembly: Insert the spring pin so that the waveform (A) of the spring
pin faces in the longitudinal direction of the paper exit drive
gear long hole (B).<R>Be sure to insert two ribs (C) into the
groove (D).
groove (D).
F. Paper exit interface PWB
(when the job separator is installed)
G. Paper exit sensor/duplex sensor
(A) Exit sensor
(B) Duplex sensor
(1)
(2)
(1)
(1)
(2)
(3)
(4)
(5)
(3)
(1)
(1)
(2)
(A)
(B)
(D)
(C)
(C)
(1)
(1)
(2)
(2)
(3)
(4)
(4)
(3)
(3)
(3)
(4)
(1)
(2)
(1)
(1)
(2)
(1)
(3)
(1)
(A)
(B)
[10]DISASSEMBLY.fm 8 ページ ２００４年１１月１２日 金曜日 午後２時１７分
Click on the first or last page to see other AR-M165-207 (serv.man17) service manuals if exist.