Sharp AR-M165-207 (serv.man17) Service Manual ▷ View online
AR-M207 M165 M162 SIMULATIONS 7-42
50
10
Paper off-center adjustment
Used to adjust the output area (main scanning direction) of scanned image data on paper.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
Note 1: Items marked with (*) are displayed when TRAY2 and following options are not installed.
Note 2: When executing an adjustment copy from the manual paper feed (BYPASS) tray, set the following
Note 2: When executing an adjustment copy from the manual paper feed (BYPASS) tray, set the following
paper according to the destination specification.
AB series
AB series
A3 paper
Inch series
Double Letter paper
The adjustment value is in the range of 1 - 99. (Default: 50)
When the adjustment value is increased, the output image is shifted to the right. When the adjustment value
is increased by 1, the image is shifted to the right by about 0.1mm.
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When the adjustment value is increased, the output image is shifted to the right. When the adjustment value
is increased by 1, the image is shifted to the right by about 0.1mm.
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
Default:
1
1
Main
code
code
Sub
code
Contents
Remark
(Adjustment item selection window)
Sim50-10 PRT. CENTER
1:TRAY1
2:TRAY2
3:TRAY3
1/2 [ 1- 99]
2:TRAY2
3:TRAY3
1/2 [ 1- 99]
50
50
50
50
50
Sim50-10 PRT. CENTER
4:TRAY4
5:BYPASS
6:DUPLEX
2/2 [ 1- 99]
5:BYPASS
6:DUPLEX
2/2 [ 1- 99]
50
50
50
50
50
Display text
:Adjustment mode
1:TRAY1
:Print center offset (TRAY1)
2:TRAY2 (*)
:Print center offset (TRAY2)
3:TRAY3 (*)
:Print center offset (TRAY3)
4:TRAY4 (*)
:Print center offset (TRAY4)
5:BYPASS
:Print center offset (BYPASS)
6:DUPLEX (*)
:Print center offset (DUPLEX 2nd print surface)
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm 42 ページ 2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-43
50
12
Document off-center adjustment
Used to adjust the scanning start position in the main scanning direction of the document.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
(Note) 2:SPF(SIDE1) is available only for the model with the SPF/RSPF.
(Note) 3:SPF(SIDE2) is available only for the model with RSPF.
(Note) 3:SPF(SIDE2) is available only for the model with RSPF.
The adjustment value is in the range of 1 - 99. (Default: 50)
When the adjustment value is increased, the document scanning position is shifted to the right and the
image is shifted to the left as a result.
When the adjustment value is increased by 1, the scanning area is shifted by 0.1mm.
When the adjustment value is increased, the document scanning position is shifted to the right and the
image is shifted to the left as a result.
When the adjustment value is increased by 1, the scanning area is shifted by 0.1mm.
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
Main
code
code
Sub
code
Contents
Remark
Sim50-12 ORG. CENTER
1:OC
2:SPF(SIDE1)
3:SPF(SIDE2)
2:SPF(SIDE1)
3:SPF(SIDE2)
[ 1- 99]
50
50
50
50
50
(Adjustment item selection window)
Display text array : Adjustment mode
1: OC
1: OC
: OC document off-center adjustment
2: SPF (SIDE1)
: SPF document (front) off-center adjustment
3: SPF (SIDE2)
: SPF document (back) off-center adjustment
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm 43 ページ 2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-44
50
18
Memory reverse position adjustment in duplex copy
Used to adjust the reverse point (scanning end position) on the reversed surface in duplex copy.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed
The adjustment value is in the range of 1 - 99. (Default: 50)
Front surface print in S-D mode and even page print in D-S mode are reverse memory copy operations from
the document rear edge.
When, therefore, the print start position adjustment of the output image is required, adjust as follows:
Front surface print in S-D mode and even page print in D-S mode are reverse memory copy operations from
the document rear edge.
When, therefore, the print start position adjustment of the output image is required, adjust as follows:
The image in the reverse memory copy is printed from the scanning rear edge when the document scanning
direction is in the arrow direction as shown below.
If, therefore, the print lead edge is shifted, set the reference chart with the rear edge on the reference
position, and adjust the simulation set value with this simulation so that the print image lead edge matches.
direction is in the arrow direction as shown below.
If, therefore, the print lead edge is shifted, set the reference chart with the rear edge on the reference
position, and adjust the simulation set value with this simulation so that the print image lead edge matches.
Since printing is started at the print start position from the last memory image data to the head data, the end
data position saved in the memory is changed by changing the scanning end position with the simulation,
adjusting the image lead edge position.
data position saved in the memory is changed by changing the scanning end position with the simulation,
adjusting the image lead edge position.
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying.
Main
code
code
Sub
code
Contents
Remark
Sim50-18 DUP REV.
1:OC
2:SPF
2:SPF
[ 1- 99]
50
50
50
(Adjustment item selection window)
Display text array : Adjustment mode
1: OC
1: OC
: OC memory reverse output position
2: SPF
: SPF memory reverse output position
Scan end position
(Default: Void (1) is not scanned.)
(Default: Void (1) is not scanned.)
Scan direction
Scan rear edge
Scan lead edge
Document transport
direction
direction
Print lead edge
Lead edge void (1
Print start position
Lead edge void (1
Print start position
Rear edge void
Print rear edge
Print rear edge
Paper transport
direction
direction
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm 44 ページ 2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-45
50
19
Rear edge void adjustment in duplex copy
Used to adjust the rear edge void amount in duplex copy.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
When this simulation is executed, the selection window of the adjustment items and the current set value
are displayed.
The adjustment value is in the range of 1 - 99. (Default: 50)
When the adjustment value is increased by 1, the rear edge void amount is increased by about 0.1mm.
When the adjustment value is increased by 1, the rear edge void amount is increased by about 0.1mm.
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and
performs copying
Main
code
code
Sub
code
Contents
Remark
Sim50-19 DUP R VOID
1:PRV(SIDE1)
2:PRV(SIDE2)
3:RRC-D
2:PRV(SIDE2)
3:RRC-D
[ 1- 99]
50
50
50
50
50
(Adjustment item selection window)
Display text array : Adjustment mode
1: PRV (SIDE1)
1: PRV (SIDE1)
: Paper rear edge void amount (1st print surface)
2: PRV (SIDE2)
: Paper rear edge void amount (2nd print surface)
3: RRC-D
: Print start position (2nd print surface)
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm 45 ページ 2004年11月17日 水曜日 午後12時11分
Click on the first or last page to see other AR-M165-207 (serv.man17) service manuals if exist.