DOWNLOAD Sharp AR-M165-207 (serv.man17) Service Manual ↓ Size: 13.1 MB | Pages: 127 in PDF or view online for FREE

Model
AR-M165-207 (serv.man17)
Pages
127
Size
13.1 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Service Manual
File
ar-m165-207-sm17.pdf
Date

Sharp AR-M165-207 (serv.man17) Service Manual ▷ View online

AR-M207 M165 M162 SIMULATIONS 7-38
49
01
Flash Rom program writing mode
Used to download the programs and data sections of the main unit MCU/IMC board, the FAX board, and the 
operation panel.
When this simulation is executed, the machine immediately shifts to the download mode and the following 
display is shown.
O When entering the download mode
Connect the main unit and the download PC with a USB cable, and start downloading with the maintenance 
tool.
When downloading is started, the display is changed as follows:
O Receiving download data
O Processing download data
O When downloading is completed
O When an error occurs
Used to display an error code at the error position in downloading of MCU/IMC/FAX/PANEL.
The error codes to be displayed are shown below.
Main 
code
Sub 
code
Contents
Remark
Download Mode.
 
Download Data
Receiving.
 
Do not turn the
power off.
 
Processing finished.
Turn off the power.
 
Error.
MCU :
--
IMC
:
--
FAX
:
--
   PNL
:
--
[07]SIMULATIONS.fm  38 ページ  2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-39
49
01
Main 
code
Sub 
code
Contents
Remark
MCU
IMC
PANEL
0xFF
No process
No process
No process
0x00
OK
OK
OK
0x01
Data receive error (Protocol error 1)
IMC sum check error
Flash Rom delete error
0x02
Data receive error (Command error) 
IMC verify error
Flash Rom write error Boot
0x03
Data receive error (Protocol error 2) 
Flash Rom write error (Program 
section)
0x04
Loader transfer error
Flash Rom write error (Common 
window data)
0x05
Flash Rom delete error (Boot)
Flash Rom write error (Copy window 
data)
0x06
Flash Rom delete error (Program)
Flash Rom write error (Scan window 
data)
0x07
Flash Rom write error (Boot)
Flash Rom write error (Print window 
data)
0x08
Flash Rom write error (Program)
Flash Rom write error (Fax window 
data)
0x09
Flash Rom LOCK error (Boot)
0x0A
Flash Rom LOCK error (Boo)
Flash Rom write error  (Fax window 
data)
0x0B
Sum check error (Loader)
FROM size error
0x0C
Sum check error (Boot)
Destination error
0x0D
Sum check error (Boot)
Download file structure error
0x0E
Sum check error (EEPROM)
0x0F
EEPROM read error
0x10
EEPROM write error 
Sum check error  (Boot not-written)
0x11
EEPROM verify error
Sum check error  (Loader)
0x12
Download data length error
Sum check error  (After Boot writing)
0x13
IMC communication error (Message 
test send error)
Sum check error  (Program)
0x14
IMC communication error (Message 
test send error)
Sum check error  (Common window 
data)
0x15
IMC communication error (Download 
request send error)
Sum check error  (Copy window data)
0x16
IMC communication error (Download 
request parameter send error)
Sum check error  (Scan window data)
0x17
MCU receive error (Overrun, Fleming, 
parity) 
Sum check error  (Print window data)
0x18
MCU receive time-out 
Sum check error  (Fax window data)
0x19
FAX communication error
Panel-MCU communication error 
0x1A
PANEL communication error
0x1B
Download file error
Download file error
FAX
0xFF
No process
0x44
FONT Flash write error
0x00
OK
0x45
FONT Flash sum check error
0x01
Download impossible
0x52
Registration data work sum check error
0x02
Total data size error
0x56
Registration data format error
0x03
LOADER no file
0x57
Registration data items insufficient error
0x04
DWLD no file
0x58
Registration data items overlap error
0x05
BOOT no file
0x61
BOOT data size error
0x06
MAIN no file
0x62
BOOT work sum check error
0x07
FONT download impossible
0x63
BOOT Flash erase error
0x08
Option FLASH connection error
0x64
BOOT Flash write error
0x09
Option FLASH no match
0x65
BOOT Flash sum check error
0x11
LOADER data size error 
0x71
MAIN data size error
0x12
LOADER work sum check error
0x72
MAIN work sum check error
0x21
BOOT data size error
0x73
MAIN Flash erase error
0x22
BOOT work sum check error
0x74
MAIN Flash write error
0x23
BOOT Flash erase error
0x75
MAIN Flash sum check error
0x24
BOOT Flash write error
0x81
FONT data size error
0x25
BOOT Flash sum check error
0x82
FONT work sum check error
0x31
MAIN data size error
0x83
FONT Flash erase error
0x32
MAIN work sum check error
0x84
FONT Flash write error
0x33
MAIN Flash erase error
0x85
FONT Flash sum check error
0x34
MAIN Flash write error
0x91
DWLD data size error
0x35
MAIN Flash sum check error
0x92
DWLD work sum check error
0x41
FONT data size error
0x93
DWLD Flash erase error
0x42
FONT work sum check error
0x94
DWLD Flash write error
0x43
FONT Flash erase error
0x95
DWLD Flash sum check error
[07]SIMULATIONS.fm  39 ページ  2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-40
50
01
Image lead edge adjustment
Used to adjust the following items related to the lead edge adjustment.
1.Print start position (Offset between output image and paper 
 Adjusted for each tray.)
2.Image lead edge void (Margin on the output image lead edge)
3.Document scanning start position (Image scanning start position in the sub scanning direction)
When this simulation is executed, the selection window of the adjustment items and the set value are 
displayed.
Note 1: Items marked with (*) are displayed when TRAY2 and following options are not installed.
Note 2: When executing an adjustment copy from the manual paper feed tray, set the following paper.
AB series
 A3 paper
Inch series
 Double Letter paper
Note 3: When the adjustment value of the print start position adjustment is increased by 1, the ON timing of 
the resist roller is delayed and the print result is shifted to the lead edge by 0.1mm.
Note 4: When the adjustment value of the image scanning start position is increased by 1, the scanning 
start position is shifted to the home position by about 0.1mm, increasing the image loss amount.
Note 5: When the print start position (TRAY1) is changed, the print start positions (TRAY2 - TRAY4) and the 
print start position (MULTI BYPASS) are also changed accordingly.
The adjustment value is in the range of 1 - 99. (Default: 50)
Select an adjustment item (mode) with the cross key, and enter the set value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy 
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and 
performs copying.
Main 
code
Sub 
code
Contents
Remark
(Adjustment item selection window)
Sim50-1 LEAD EDGE
1:TRAY1
2:TRAY2
3:MFT
1/2     [      1-  99]
50
50
50
50
Sim50-1 LEAD EDGE
4:DEN-A
5:RRC-A
6:DEN-B
2/2     [      1-  99]
50
50
50
50
Display text
:Adjustment mode
1:TRAY1
:Print start position (TRAY1)
2:TRAY2 (*)
:Print start position (TRAY2 - TRAY4)
3:MFT
:Print start position (MULTI BYPASS)
4:DEN-A
:Image lead edge void amount
5:RRC-A
:Document scanning start position
6:DEN-B
:Image rear edge void amount
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm  40 ページ  2004年11月17日 水曜日 午後12時11分
AR-M207 M165 M162 SIMULATIONS 7-41
50
01
(Adjustment procedure)
(1) Set the print start position (1: TRAY1), the lead edge void amount (4: DEN - A), and the scanning start 
position (5: RRC - A) to "1" and make a copy of 100%.
(2) Measure the image loss amount (R mm) of the scale.
Set [5:RRC - A] = 10xR(mm). (Example. Set 40.)
When the value of [5: RRC - A] is increased by 10, the image loss is decreased by1mm. (Default: 50)
(3) Measure the distance (H mm) from the paper lead edge to the image print start position.
Set [1:TRAY1] = 10xH(mm). (Example: Set 50.)
When the value of [1:TRAY1] is increased by 10, the image lead edge shifts to the paper lead edge by 
1mm. (Default: 50)
(4) Set the lead edge void amount to B = 50(2.5mm). (Default: 50)
When the value of [4:DEN - A] is increased by 10, the void amount is increased by about 1mm. (For 25 
or less, the void amount is zero.)
[Example]
06
Copy lead edge position adjustment (SPF/RSPF)
Used to perform the image lead edge adjustment in the SPF/RSPF copy.
When this simulation is executed, the selection window of the adjustment items and the current set value 
are displayed.
The adjustment value is in the range of 1 - 99. (Default: 50). When the adjustment value of the document 
scanning start position is increased by 1, the scanning timing is advanced, resulting in a smaller image loss.
Select an adjustment item (mode) with the cross key and enter a desired value with 10-key.
When [OK] key is pressed, the entered value is saved to the EEPROM and the machine shifts to the copy 
execution window.
After completion of copying, the machine returns to the adjustment value input window.
When [START] key is pressed instead of [OK] key, the machine shifts to the copy execution window and 
performs copying.
Main 
code
Sub 
code
Contents
Remark
Copy output result
Distance between the
paper lead edge to the
image lead edge
H=5.0mm
Paper lead edge
Scale image loss
amount
R=4.0mm
Sim50-6  SPF EDGE
1:SIDE1
2:SIDE2
3:END EDGE
     [      1-  99]
50
50
50
50
(Adjustment item selection window)
Display text array : Adjustment mode
1: SIDE1
: Document (front) scan start position adjustment
2: SIDE2
: Document (back) scan start position adjustment
3: END EDGE
: Document rear edge image loss adjustment
Ready to copy.
S
100%
8 1/2
11
(Copy start window)
Copies in progress.
S
100%
8 1/2
11
(Copy execution window)
Adjustment
item selection
window
Copy start
window
Copy execution
window
OK
BACK
START
START
End of copy execution
[07]SIMULATIONS.fm  41 ページ  2004年11月17日 水曜日 午後12時11分
Page of 127
Display

Click on the first or last page to see other AR-M165-207 (serv.man17) service manuals if exist.