Sharp AR-FX2 (serv.man2) Service Manual ▷ View online
SW
NO.
Data
NO.
Item
Switch selection and contents of functions
Initial value
User
program
No.
Remark
SW15
1
Lower limit of
busy tone
detection time
(1)
busy tone
detection time
(1)
Used to set the lower limit of busy tone detection time
(ON time).
(ON time).
250 ms
0
2
Upper limit of
busy tone
detection time
busy tone
detection time
Used to set the upper limit of busy tone detection time
(ON time).
(ON time).
750 ms
0
3
Lower limit of
busy tone
detection time
(2)
busy tone
detection time
(2)
Used to set the lower limit of busy tone detection time
(ON time).
(ON time).
Follows
setup of
SW15-1
setup of
SW15-1
0
4
Reserved
0
5
Modem speed
(other than
V.33 mode)
(other than
V.33 mode)
Used to set the communication start speed other in a
mode other than V.34 mode. In areas of poor
communication conditions, this setup is used to reduce
the communication speed in advance.
mode other than V.34 mode. In areas of poor
communication conditions, this setup is used to reduce
the communication speed in advance.
V.17
14.4 kbps
14.4 kbps
1
For the bits
marked with
marked with
∗,
set to V.17
14.4 kbps.
14.4 kbps.
6
0
7
0
8
0
SW16
1
Reserved
0
2
External
telephone
connection
telephone
connection
Used to set whether an external telephone is connected
or not.
or not.
YES
1
106
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Rotation
transmission
select (A4
transmission
select (A4
→
A4R)
Used to set whether A4 document is sent as A3 width
(A4) or it is sent as A4R by rotating read images.
(A4) or it is sent as A4R by rotating read images.
YES
1
125
7
Reserved
0
8
Reserved
0
SW17
1
Reserved
0
2
Output
conditions setup
conditions setup
Used to set the size of paper to output when a
document is received.
document is received.
A: Optimum size output (Received size)
B: Larger than the optimum
C: Divided output
D: Reduced output
B: Larger than the optimum
C: Divided output
D: Reduced output
ABD
0
133
When set to
“11” or “01”,
set to “00”
(ABD).
“11” or “01”,
set to “00”
(ABD).
3
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1: 350 ms
0: 250 ms
1: 650 ms
0: 750 ms
1: 150 ms
0: Follows setup of SW15-1
SW15 Bit No.
5 6 7 8
SW15 Bit No.
5 6 7 8
V.27 2400 bps
0 0 0 0
V.17 14.4 kbps
1 0 0 0
V.29 9600 bps
0 0 0 1
V.17 9600 bps
1 0 0 1
V.27 4800 bps
0 0 1 0
V.17 12.0 kbps
1 0 1 0
V.29 7200 bps
0 0 1 1
V.17 7200 bps
1 0 1 1
V.33 14.4 kbps
0 1 0 0
★
1 1 0 0
★
0 1 0 1
★
1 1 0 1
V.33 12.0 kbps
0 1 1 0
★
1 1 1 0
★
0 1 1 1
★
1 1 1 1
1: YES
0: NO
1: YES
0: NO
SW17 Bit No.
2 3
ABD
0 0
ABC
1 0
AR-FX2
6 – 7
SW
NO.
Data
NO.
Item
Switch selection and contents of functions
Initial value
User
program
No.
Remark
SW18
1
Reserved
0
2
Reserved
0
3
Reception size
specification
(Shows
reception
capacity.)
specification
(Shows
reception
capacity.)
Used to set the receivable document width which is
informed the other party when receiving a
communication. The setup items are as follows:
informed the other party when receiving a
communication. The setup items are as follows:
By the
installed
cassette
installed
cassette
0
∗1: Refer to
the following
descriptions.
<Only Inch
Series>
the following
descriptions.
<Only Inch
Series>
4
0
5
11
″ reception
capacity setup
Used to set the recording width of DIS signal when the
set paper size is Ledger (11
set paper size is Ledger (11
× 17, main scanning
279.4mm, sub scanning 431.8mm), Letter R (8.5
× 11R,
main scanning 215.9mm, sub scanning 279.4mm), Letter
(8.5
(8.5
× 11, main scanning 279.4mm, sub scanning
215.9mm) or Legal (8.5
× 14, main scanning 215.4mm,
sub scanning 355.6mm).
For each setup, be careful of the following items.
<255mm and 215mm>
When the other party sends documents of 11
<255mm and 215mm>
When the other party sends documents of 11
″ width or
A3 width, the size is automatically reduced to 255mm in
the other party’s machine.
<303mm, 255mm, and 215mm>
When the other party sends documents of 303mm width,
and when reception is made on Ledger, Letter, or Letter
R (rotation print) paper, the data over the paper size are
cut out. (When printed on Legal paper in rotation
printing, the data are not cut.) In this case, if the other
party’s machine is of inch spec and sends documents of
11
the other party’s machine.
<303mm, 255mm, and 215mm>
When the other party sends documents of 303mm width,
and when reception is made on Ledger, Letter, or Letter
R (rotation print) paper, the data over the paper size are
cut out. (When printed on Legal paper in rotation
printing, the data are not cut.) In this case, if the other
party’s machine is of inch spec and sends documents of
11
″ width, there is no problem. If the other party’s
machine is of AB spec and sends document of A3 width,
data are cut.
data are cut.
303/255/
215 mm
215 mm
0
∗2 Refer to the
following
descriptions.
<Only Inch
Series>
following
descriptions.
<Only Inch
Series>
6
Output method
in A3 width
reception
in A3 width
reception
Used to set the output method when A3 width data are
sent from the other party’s machine.
sent from the other party’s machine.
11
″ width
print
0
126
<Only Inch
Series>
Series>
7
Reserved
0
8
Reserved
0
SW19
1
Protocol monitor
Used to set whether the protocol monitor of one
communication is printed or not.
communication is printed or not.
NO
0
2
Send
reservation
interruption
enable in recall
mode
reservation
interruption
enable in recall
mode
Used to set whether send reservation interruption is
allowed or not in standby for recall.
allowed or not in standby for recall.
Enable
1
115
SW18 Bit No.
3 4
By the installed cassette
0 0
215 mm
1 0
255 mm (215 & 255 mm)
0 1
303 mm (215 & 255 & 303 mm)
1 1
∗1: When “By the installed cassette” is selected, the max. recording size on the tray which is set to ON in the recording paper tray selection
(SW27-2 – 5) becomes effective.
When all of the recording paper tray selection (SW27-2 – 5) are set to OFF, the reception of A3 (A4, B4, A3) is allowed. (The soft SW is
not changed.)
When all of the recording paper tray selection (SW27-2 – 5) are set to OFF, the reception of A3 (A4, B4, A3) is allowed. (The soft SW is
not changed.)
∗2: When 11″ paper which allows reception of FAX is set, setting of this SW informs of the reception capability.
If the setting of SW18-3 to -4 (Reception size designation) is set to “By the installed cassette”, this setting has the priority.
1: 255/215 mm
0: 303/255/215 mm
1: Data of A3 width is
printed.
printed.
0: Data of 11
″ width is
printed.
1: YES
0: NO
1: Enable
0: Disable
AR-FX2
6 – 8
SW
NO.
Data
NO.
Item
Switch selection and contents of functions
Initial value
User
program
No.
Remark
SW19
3
Output only in
case of
protocol
monitor error
case of
protocol
monitor error
Effective only when SW19-1 is set to 1 (YES). Used to
set whether protocol monitor is outputted only when a
communication is not completed normally due to a
communication error or it is outputted after completion of
every communication.
set whether protocol monitor is outputted only when a
communication is not completed normally due to a
communication error or it is outputted after completion of
every communication.
NO
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Time
designation 1
of
communication
record table
designation 1
of
communication
record table
Used to set whether the communication record table is
printed at the designated time 1 or not.
printed at the designated time 1 or not.
Disable
0
139
8
Time
designation 2
of
communication
record table
designation 2
of
communication
record table
Used to set whether the communication record table is
printed at the designated time 2 or not.
printed at the designated time 2 or not.
Disable
0
139
SW20
1
Line sound
monitor range
monitor range
Used to set the line sound monitor range when the line
monitor function is used.
When set to “Until NSF signal send/receive”, monitoring
is made until the NSF signal is sent or received. When
set to “All”, monitoring is made for all until the line is
disconnected.
monitor function is used.
When set to “Until NSF signal send/receive”, monitoring
is made until the NSF signal is sent or received. When
set to “All”, monitoring is made for all until the line is
disconnected.
OFF
0
When set to
“11”, set to “00”.
“11”, set to “00”.
2
0
3
Line monitor
display
display
Used to set whether the communication speed and the
reception level are displayed on the LCD or not.
reception level are displayed on the LCD or not.
NO
0
4
Operation
panel key
sound
panel key
sound
Used to set whether the key click sound of FAX related
keys are made or not when operating in the FAX mode.
keys are made or not when operating in the FAX mode.
Ring
0
5
Receivable
memory
capacity left
memory
capacity left
Used to set the remaining memory capacity for
acceptance of call. (This is not the memory judgement
level during reception.)
acceptance of call. (This is not the memory judgement
level during reception.)
128 Kbyte
0
6
Memory over
during reception
during reception
Used to set whether the received data are outputted or
destroyed when memory is over during reception.
destroyed when memory is over during reception.
Output
1
7
Reserved
0
8
Reserved
0
1: Only in case of an
error
error
0: After completion of
every communication (All
output)
every communication (All
output)
1: Enable
0: Disable
1: Enable
0: Disable
SW20 Bit No.
1 2
OFF
0 0
Until NSF signal send/receive
0 1
All
1 0
1: YES
0: NO
1: Not ring
0: Ring
1: 64Kbyte
0: 128Kbyte
1: Output
0: Not output
AR-FX2
6 – 9
SW
NO.
Data
NO.
Item
Switch selection and contents of functions
Initial value
User
program
No.
Remark
SW21
1
Interval
between the
end of a
communication
and the next
call
between the
end of a
communication
and the next
call
Used to set the time interval between the end of a
communication and a call for the next communication.
communication and a call for the next communication.
Europe:
6 sec
Australia:
3 sec
6 sec
Australia:
3 sec
0
2
0
3
0
4
0
5
0
6
∗
7
∗
8
∗
SW22
1
Reserved
0
2
Reserved
1
3
Reserved
1
4
Reserved
0
5
Reserved
0
6
Reserved
1
7
Reserved
1
8
Reserved
1
SW23
1
Reserved
0
2
Reserved
1
3
Reserved
1
4
Reserved
1
5
Reserved
1
6
Reserved
0
7
Reserved
1
8
Reserved
0
SW24
1
Reserved
1
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Received
document
output setup
document
output setup
Used to set whether all received documents are
outputted at a time after completion of reception or each
document is outputted every time when it is received.
outputted at a time after completion of reception or each
document is outputted every time when it is received.
All
received
documents
are
outputted
at a time
after
completion
of
received
documents
are
outputted
at a time
after
completion
of
1
7
Reserved
0
8
Auto reduction
print
Used to set whether auto reduction print is made or not
when the received document size is greater than the
fixed size and smaller than the length of auto reduction
line number setup. When auto reduction print is set to
Enable, larger or smaller documents are printed in the
fixed size.
when the received document size is greater than the
fixed size and smaller than the length of auto reduction
line number setup. When auto reduction print is set to
Enable, larger or smaller documents are printed in the
fixed size.
Enable
1
132
SW21 Bit No.
1 2 3 4 5 6 7 8
Set range
0 – 255 sec in the increment of 1
sec (Binary input)
sec (Binary input)
1: All received
documents are outputted
at a time after
completion of
documents are outputted
at a time after
completion of
0: Each document is
outputted every time
when it is received.
outputted every time
when it is received.
1: Enable
0: Disable
AR-FX2
6 – 10
Click on the first or last page to see other AR-FX2 (serv.man2) service manuals if exist.