DOWNLOAD Sharp AR-FX13 Service Manual ↓ Size: 2.14 MB | Pages: 72 in PDF or view online for FREE

AR-FX13  FAX SOFT SWITCH  5 - 24

Used to set YES/NO of CSI signal send.

CSI signal includes the sender's number.

Default: 1 (Yes)

Used to set YES/NO of DIS receive check in G3 mode send.

When set to 1, DIS receive twice is checked.

When set to 0, DIS once is checked when "NSF/DIS" is received;
and DIS twice is checked when NSF is not received.

Default: 0 (Once in NFS reception, 2 time in DIS reception)

Used to set detection timer of EOL (EndOfLine) in Phase C receive.

Default: 0 (13sec)

Used to set the interval from CED send to FSK signal send of DIS.

Default: 1 (500ms)

Used to set the interval from DIS receive to DSC signal send.

Default: 0 (500ms)

Used to set the minimum required time for detection of dial tone
when the dial tone detection is set to "YES" and the kind of the dial
tone detection is set to "Continuous."

Default: 0 (100ms)

Used to set whether dial tone is detected or not when calling out.

When set to 1, dial tone is detected before calling out.

When set to 0, dial tone is not detected and dialing is made after a
certain time (3.5sec).

Default: 1 (Yes) (U.S.A.) / 0 (No) (Other than U.S.A.)

Used to set YES/NO of busy tone detection when calling out.

Default: 1 (Yes)

Used to set the monitoring time when detecting dial tone.

Default: 0 (5sec)

Used to set the upper limit time for detection of dial tone when the
dial tone detection is set to "YES" and the kind of the dial tone detec-
tion is set to "Intermittent."

If a dial tone is detected for more than this upper limit time, it is not
considered as a dial tone.

Default: 0 (700ms)

Used to set max. length of reception for long document.

Default: 0 (1.5m)

Used to set the time from displaying the destination to the next oper-
ation in one-touch dial or reduction dial.

Default: 0 0 (2sec)

Used to set whether memory send is ON or direct send is made
(OFF) in the memory mode when pressing [Clear All] key or auto
clear.

Default: 0 (Memory transmission)

Used to set whether proxy reception is enabled or not.

When set to 0, under the following error status, auto receive is not
made in auto receive mode.

• Cover open

• Unit error (Toner, drum, developing-related errors)

• Recording paper JAM

• Document JAM

• Recording paper empty

When set to 1, proxy reception is allowed.

Default: 1 (Yes)

Used to set whether quick online send function is enabled or not.

When set to 0, send in memory mode ON is made in memory send.

When set to 1, send in memory mode ON is made in quick online
send.

Default: 1 (Yes)

Used to set whether remote select function is enabled or not.

Default: 1 (Yes)

Used to set the number of times of CNG detection for judgment of
detection.

Default: 3 times

Used to set whether the total communication time and total pages
are printed on the communication report or not.

When set to 1, the total communication time and total pages are
printed on the communication report.

When set to 0, the total communication time and total pages are not
printed on the communication report.

Default: 1 (Yes)

Used to set ringing volume pattern.

Default: 7 (North America) / 1 (Other than North America)

Used to set YES/NO of measurement of communication time in
phase C. It is the communication time in the latest phase C. (Unit:
msec)

Valid only in ECM communication.

Default: 1 (Yes)

Used to set whether registered sender's telephone number can be
changed or not.

Default: 0 (Allow)

AR-FX13  FAX SOFT SWITCH  5 - 25

Used to set the frame size of error correction mode to be notified to
the remote machine.

Default: 0 (256 [bytes/frame])

Used to set call time in automatic send.

Setting is made by binary input of N into "(5sec x N) + 30sec" in the
increment of 5sec.

Default: 45sec

Used to set the detection frequency of CI signal (call signal).

Default: 0 0 (4 sine wave)

Used to set the ringing volume when call-in.

Default: 1 0 (Medium)

Used to set the volume of transmission and DTMF sound from the
speaker when SPEAKER key is pressed.

Default: 1 0 (Medium)

Used to set the lower limit of busy tone detection time (ON time).

Default: 0 (250ms)

Used to set the upper limit of busy tone detection time (ON time).

Used to set the lower limit 2 of busy tone detection time (ON time).

Used to set signal send level from MODEM.

Setting is made in binary input in the increment of 1dBm.

Used to set send start speed in communication other than V.34
mode.

In an area of poor communication conditions, it is recommended to
set communication speed to a lower level in advance.

Default: 1 0 0 0 (V.17 14.4kbps)

Used to set receive procedure start speed in a remote machine
other than V.34.

In setting of no fixing, the operations are the same as V.17-
14400BPS.

Default: 0 0 (No fixing)

Used to set whether coding capacity is fixed to MH or not in commu-
nication other than SG3.

Default: 0 (No)

Used to set whether MMR coding capacity is allowed or not in com-
munication other than SG3.

Default: 1 (Yes)

Used to set whether JBIG coding capacity is allowed or not in com-
munication other than SG3.

Default: 1 (Yes)

Used to set whether coding capacity is fixed to MH or not in SG3
communication.

Default: 0 (No)

Used to set whether MMR coding capacity is allowed or not in SG3
communication.

Default: 1 (Yes)

Used to set whether JBIG coding capacity is allowed or not in SG3
communication.

Default: 1 (Yes)

Used to set whether communication report is automatically output-
ted or not when the number of send/receive items which have not
outputted yet on communication report reaches 50.

When set to 1, they are automatically outputted.

When set to 0, they are not outputted even the number of items
reaches 50.

Default: 0 (No)

Used to set line sound monitor range when line sound monitor func-
tion is used.

Default: 0 0 (OFF)

Used to set whether the communication speed and the receive level
are displayed on LCD or not.

Default: 0 (No)

Used to set the remained memory capacity for allowing call-in.

Default: 0 (128Kbyte)

Used to set the interval between completion of communication and
the next call.

Setting is made in binary input.

Default: 1sec (North America) / 6sec (Other than North America)

Default: 0 (750ms) (North America, Europe) / 

1 (650ms) (Australia, New Zealand)

Default: 0 (Follows SW15-1.) (North America) / 

1 (150ms) (Other than North America)

Default: –12dBm (North America, New Zealand) / 

–11dBm (Europe) / –9dBm (Australia)

AR-FX13  FAX SOFT SWITCH  5 - 26

Used to set whether the FAX receive rejection function is made valid
or not for registered FAX numbers.

Default: 0 0 (Not set.)

Used to set the document output procedure; whether all the received
documents are collectively outputted after completion of reception or
every page is outputted when it is received.

Used to set whether automatic reduction print is performed or not so
that a document longer than the fixed size and smaller than the auto-
matic reduction line number setting is printed on fixed size paper.

Default: 1 (Allow)

Used to set automatic reduction rate when automatic reduction print
is valid.

Default: 10%

Used to set transmission end sound tone in transmission.

Default: 0 1 (1000Hz)

Used to set reception end sound tone in reception.

Default: 0 1 (1000Hz)

Used to set whether buzzer sound is made or not when scan is com-
pleted.

In manual send or when scan is completed in direct send, buzzer
sound is not made.

Default: 0 (1sec)

Used to set speaker volume.

The following sounds are the targets of this setting.

• Alarm sound

• Send end sound

• Receive end sound

• Scan end sound

Default: 0 1 (Small)

Used to select the recording paper tray used by FAX.

Valid only when two cassettes are installed.

Default: 0 0 (AUTO)

→ auto reception

Used to set the number of calls to switch to auto receive in manual
receive mode.

When set to 0, switch to auto receive is not made.

Default: 0 time

Used to set the number of calls before starting reception in auto
receive mode.

Setting is made in binary input.

Default: 2 times

Used to set whether the user cancel report is outputted or not when
send is canceled during document send.

Default: 0 (Not output)

Used to set whether sender information (registered in the sender
registration), sending date, and time are printed on the upper edge
of send document or not.

Default: 1 (ON)

Used to set whether date/sender information is printed inside the
document area or outside the document area.

Default: 0 (Outside of document)

Used to set whether communication report is outputted or not after
completion of sending (excluding sequential broadcast and sequen-
tial send request).

Default: 1 0 (Only when transmission is failed.)

Used to set whether communication report is outputted or not after
completion of sending (sequential broadcast and sequential send
request).

Default: 0 1 (All print)

Used to set whether communication report is outputted or not in
reception.

Default: 0 0 (Print inhibited)

Used to set whether part of send document is printed on the commu-
nication report or not in memory send.

Default: 1 0 (Only the address to which transmission is failed)

Used to set the ringing pattern as FAX reception.

Default: 0 0 0 0 (OFF)

Used to set whether the index is printed when outputting received
document or not.

Default: 0 (Not print)

Used to set whether the page number is added to the sender infor-
mation print or not.

Default: 1 (Yes)

Default: 0 (Output after reception of every page)  (North America) / 

1 (Collective output after completion of reception) (Other
than North America)

AR-FX13  FAX SOFT SWITCH  5 - 27

Used to set whether duplex print of received data is made or not.

Default: 0 (No)

Used to set the time from off-hook to Flash send.

Default: 1 0 (1sec)

Used to set the max. signal send level.

Default: –8dBm

Used to set whether cover is added as default or not.

When auto clear is made by pressing [Clear All] key, the machine
returns to this setting.

Default: 0 (No)

Used to set the max. wait time between detection of CI signal pulse
(number of times) and detection of the next CI signal pulse.

If CIK signal pulse is not detected within this time, the number of
calls up to that time is cleared.

Default: 0 0 (5sec) (Other than Europe) / 0 1 (10sec) (Europe)

Used to set the number of calls to switch to auto receive when
answering telephone is not called in when the receive mode is set to
the answering telephone connection mode.

Setting is made in binary input.

Used to set the time for completion of CNG signal/mute detection in
the answering telephone connection mode.

Count is made from the last call signal.

Setting is made in binary input.

Default: 45sec

Used to set whether communication protocol result is printed or not
after completion of communication.

Default: 0 0 (Not printed.)

Used to set whether the protocol monitor of the last communication
is saved or not. When set to "Saved," the previous protocol monitor
can be printed with SIM66-21.

Default: 1 (Yes)

Used to set the Flash send time.

Default: 0 0 (90ms)

Used to set whether transfer function is enabled or not.

Default: 1 (Allow)

Used to set DTMF signal send time.

Setting is made in binary input by the increment of 10ms.

Default: 110ms (Other than Europe) / 80ms (Europe)

Used to set the number of times of recall when a communication
error occurs.

Setting is made in binary input.

When set to 0, recall is not made.

Default: 1 times

Used to set the number of times of recall when busy tone is detected
during transmission.

Setting is made in binary input.

When set to 0, recall is not made.

Default: 2 times

Used to set whether direct send recall wait is allowed or not.

Default: 0 (Allow)

Used to set whether FAX receive auto select is enabled or not when
CNG signal is detected with external telephone used.

Default: 1 (Allow)

Used to set whether auto receive select function in answering tele-
phone connection mode is enabled or not.

Default: 0 (Inhibit)

Used to set whether V.34 mode is enabled or not in manual commu-
nication.

When, however, SW43-1 is set to "0: OFF," V.34 mode is disabled
even tough this switch is set to "1: ON."

Default: 1 (ON)

Used to set whether V.34 mode is enabled or not as a capacity of
own machine in send/receive.

Default: 1 (ON)

Used to set symbol speed mask in V.34 receive.

Default: 1 0 1 (3429)

Used to set send start speed in V.34 send.

Setting is made in binary input of N in "2400 (bps) x N" in the range
of 2400bps – 33600bps.

N is set in the range of 0 – 15. When set to 0, 2400bps; when set to
15, 33600bps.

When set to 2400bps, all of SW91 No. 1 – 8 must be set as "Dis-
able".

Default: 33600bps

Default: 5 times (North America) / 

6 times (Other than North America)