DOWNLOAD Sharp AR-FX13 Service Manual ↓ Size: 2.14 MB | Pages: 72 in PDF or view online for FREE

AR-FX13  FAX SOFT SWITCH  5 - 32

Used to set whether use of 2743Hz is allowed or not as symbol
speed in V.34 communicate.

Default: 1 (Enable)

Used to set void amount in print image area.

Void amount on the lead edge in sub scan direction can be adjusted.
When the set value is increased, the margin on the lead edge is
increased.

Setting is made in binary input in the increment of 16 lines.

Default: 32 lines

Void amount on the rear edge in sub scan direction can be adjusted.
When the set value is increased, the margin on the read edge is
increased.

Setting is made in binary input in the increment of 16 lines.

Default: 48 lines

Used to set image loss in scan image area.

Image loss on the left edge in OC main scan direction can be
adjusted. When the set value is increased, image loss is increased.

Setting is made in binary input in the increment of 24 dots.

Default: 96 dots

Used to set image loss in scan image area.

Image loss on the right edge in OC main scan direction can be
adjusted. When the set value is increased, image loss is increased.

Setting is made in binary input in the increment of 24 dots.

Default: 96 dots

Used to set image loss in scan image area.

Image loss on the lead edge in OC sub scan direction can be
adjusted. When the set value is increased, image loss is increased.

Setting is made in binary input in the increment of 16 lines.

Default: 96 lines

Used to set image loss in scan image area.

Image loss on the rear edge in OC sub scan direction can be
adjusted. When the set value is increased, image loss is increased. 

Setting is made in binary input in the increment of 16 lines.

Default: 144 lines

Used to set image loss in scan image area.

Image loss in RSPF back surface main scan direction can be
adjusted. When the set value is increased, image loss is increased.

Setting is made in binary input in the increment of 24 dots.

Default: 96 dots

Used to set image loss in scan image area.

Image loss on the right edge in RSPF back surface main scan direc-
tion can be adjusted. When the set value is increased, image loss is
increased.

Setting is made in binary input in the increment of 24 dots.

Default: 96 dots

Used to set the main scan magnification ratio in OC scan.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

Used to set the main scan magnification ratio in OC scan.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

Used to set the sub scan magnification ratio in OC scan.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

Used to set the sub scan magnification ratio in OC scan.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

Used to set the main scan magnification ratio in RSPF back surface
scan.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

Used to set the main scan magnification ratio in RSPF back surface
scan.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

Used to set the sub scan magnification ratio in RSPF back surface
scan.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

AR-FX13  FAX SOFT SWITCH  5 - 33

Used to set the sub scan magnification ratio in RSPF back surface
scan.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

Used to set the main scan magnification ratio in back surface print.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

Used to set the main scan magnification ratio in back surface print.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

Used to set the sub scan magnification ratio in back surface print.

Bit 1 indicates plus or minus of the magnification ratio.

Default: 0 (+)

Used to set the sub scan magnification ratio in back surface print.

By binary input, setting can be made in the range of 0 – ±12.7% in
0.1% increments.

Default: 0%

AR-FX13  TROUBLE CODES  6 - 1

Communication error xx (xxxx)

(In print out, the communication error display is made. In FAX status
check, “NGxxxxxx” is displayed.

When transmission or reception is not executed normally due to dis-
tur-bance in protocol signals and image signals by the trouble in the
line, the code of 6 digits is displayed on the transmission result
check menu (reception result check menu).

Upper 2 digits of a communication error code: 00 – 58 (error code) is
displayed. (Communication result code)

Lower 4 digits of a communication error code: Error code1, Error
code 2

1) Refer to the communication result code.

2) Refer to error code 1.

3) Refer to error code 2.

(Error code 1 other than V.34 mode is “00”.)

Main 
code

Sub 

code

Details of trouble

F6

10

FAX board trouble

U1

03

FAX board battery error

Main 
code

Sub 

code

Details of trouble

F6

10

Content FAX board trouble

Detail

Communication trouble between MCU and 
FAX control PWB

Cause

FAX control PWB connector disconnection
Defective harness between FAX control PWB 
and MCU PWB
Motherboard connector pin breakage
FAX control PWB ROM error/Data error
IC on FAX PWB causes abnormality

Check 
and 
remedy

Check connector/harness of FAX control 
PWB and MCU PWB.
Check the grounding of the copier.
Check FAX control PWB ROM.
Replace the FAX PWB.

U1

03

Content FAX board battery error

Details

The SRAM backup battery voltage on FAX 
PWB falls.

Cause

The SRAM backup battery voltage on FAX 
PWB falls.

Check 
and 
remedy

Check voltage of the SRAM back up battery.
Replace the battery.

Error code 

(Communication 

result)

Communication 

report result 

column

Communication interruption 

content

0 – 31

For details of 0 – 
31, refer to the 
communication 
result code.

Depends on the 
communication 
disconnection position.
For 16 or later, V.34 mode 
communication.

33

Busy

The calling side cannot 
connect the line with the 
other party.

34

Cancel

An interruption command is 
made during transmission or 
reception.
A reservation is canceled.
An interruption command is 
entered with the interruption 
key.

35

Power OFF

Power OFF during 
transmission or reception

36

(Recording paper 
empty)

37

(Recording paper 
jam)

38

Reception 
memory over

Memory over during 
reception

39

(Discrepancy in 
the number of 
sheets)

40

(Interface not 
accepted)

41

Transmission 
length over

The length of transmission 
data of one page exceeds 
the range during 
transmission.

42

Reception length 
over

The length of reception data 
of one page exceeds the 
range during reception.

43

Communication 
(OK)

Communication enable 
before transmission

44

Document error

A document jam during 
direct transmission

45

(Image quality 
error)

46

No response 
from the other 
party

The FAX signal from the 
other party cannot detect 
within T1 time.

47

(Communication 
error)

48

OK

Communication normal end

49

No send request 
function on the 
other party

The other party has no send 
request function when 
receiving a send request.

The other party has no data 
to send.

50

Send request not 
accepted

DCN is received for DTC 
when sending a send 
request.

There is no data to send 
when sending a send 
request.

51

Send request 
enable number 
discrepancy

Discrepancy in the enable 
number when sending a 
send request.
Discrepancy in the system 
number when sending a 
send request.

52

No confidential 
function on the 
other party

The other party has no 
confidential function when 
sending a confidential 
message. (Including the 
other company’s machines)

Error code 

(Communication 

result)

Communication 

report result 

column

Communication interruption 

content

AR-FX13  TROUBLE CODES  6 - 2

(Note) For error codes 16 – 31, V.34 mode communication.

Error codes 1 are fixed to “00”.

53

Confidential 
function not 
accepted

DCN is received for NSS 
when receiving a confidential 
message.

54

Confidential box 
No. NG

A confidential box number 
which is not registered is 
directed when receiving a 
confidential message.

55

No interface 
function on the 
other party

The other party has no 
interface function when 
sending an interface 
command.

56

Interface not 
accepted

DCN is received for NSS 
when sending an interface 
command.
A receiving station number 
which is not registered is 
directed when receiving an 
interface command.

57

Interface ID 
discrepancy

Discrepancy in the interface 
ID when receiving an 
interface command.

58

Reception 
inhibition number

Transmission is made from a 
reception inhibition number.

Error 
code

Final reception signal 

(Transmitting side)

Final reception signal 

(Receiving side)

0

Abnormal signal

Abnormal signal

1

NSF, DIS

NSS, DCS

2

CFR

NSC, DTC

3

FTT

EOP

4

MCF

EOM

5

PIP, PIN

MPS

6

RTN,  RTP

PRI-Q

7

No signal

DCN

8

PPR

PPS-EOP

9

PPS-EOM

10

PPS-MPS, PPS-NULL

11

RNR

RR

12

CTR

CTC

13

ERR

EOR-Q

14

PPS-PRI-Q

15

16

Abnormal signal

Abnormal signal

17

NSF, DIS

NSS, DCS

18

CFR

NSC, DTC

19

FTT

PPS-EOP

20

MCF

PPS-EOM

21

PIP, PIN

PPS-MPS, PPS-NULL

22

RTN, RTP

PRI-Q

23

No signal

DCN

24

PPR

25

RNR

RR

26

CTR

CTC

27

ERR

EOR-Q

28

PPS-PRI-Q

29

V.8 Phase-1

V.8 Phase-1

30

V.8 Phase-2

V.8 Phase-2

31

V.8 Phase-3

V.8 Phase-3

Error code 

(Communication 

result)

Communication 

report result 

column

Communication interruption 

content

Error 

codes 2

Content of communication interruption

Transmission/

Reception

01

Transmission length over

Transmission

02

EOL time over

Reception

03

Carrier detection time up

Reception

04

Polarity reversion detection (in phase C) Transmission/

Reception

05

8 min over (in phase C)

Transmission

06

Memory image decoding error

Reception

07

Memory image decoding error

Transmission

08

Time up between frames in phase C

Transmission/
Reception

10

Communication request NG

Reception

11

Polarity reversion detection

Reception

12

Invalid command reception

Reception

13

Time over (1min timer/6sec timer)

Reception

14

PUT error

Reception

15

Time out occurrence during shift from 
Primary to Control in V.34 mode

Reception

20

Polarity reversion detection

Transmission

21

Invalid command reception

Transmission

22

Fall back retry number over

Transmission

23

Resend over of retry number

Transmission

24

Time over (T5 timer)

Transmission

25

Time over (T5 timer) in V.34 mode

Transmission

26

Time out occurrence during shift from 
Primary to Control in V.34 mode

Transmission

30

Communication error due to 
communication abnormality between 
FAX_SUB and FAX_MAIN

Transmission/
Reception