Sharp AR-F13 (serv.man2) Service Manual ▷ View online
AR-F13 DISASSEMBLY AND ASSEMBLY 5-14
10)Remove the four screws [14] to remove the upper transmission
sensor unit [15] and lower transmission sensor [16].
11) Remove the punch unit [18] from the horizontal registration motor
assembly [17].
B. PCBs
(1)Removing the Punch Controller PCB
1) Remove the two screws [1].
2) Disconnect the five connectors [2] to remove the punch controller
2) Disconnect the five connectors [2] to remove the punch controller
PCB [3].
(2)Removing the Photosensor PCB
1) Remove the punch motor. (See 2.A.(1).)
2) Remove the screw [1].
2) Remove the screw [1].
3) Remove the harness [3] from the harness guide [2] on the PCB, then
detach the PCB cover [4].
4) Disconnect the connector [5] to remove the photosensor PCB [6].
[14]
[14]
[14]
[15]
[16]
[17]
[18]
[2]
[3]
[2]
[2]
[1]
[4]
[1]
[2]
[3]
[6]
[5]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-15
(3)Removing the LED PCB
1) Remove the waste case.
2) Disconnect connector [1].
3) Remove the harness [3] from the harness guide [2].
3) Remove the harness [3] from the harness guide [2].
4) Remove the screw [4] and washer [5].
5) Disconnect the connector [6].
6) Remove the screw [7] to detach the base cover [8].
7) Remove the screw [9].
8) Disconnect the connector [10] to remove the LED PCB [11].
8) Disconnect the connector [10] to remove the LED PCB [11].
(4)Removing the Waste-Full Photosensor PCB
1) Remove the punch controller PCB. (See 2.B.(1).)
2) Remove the two screws [1] to remove the PCB film [2].
3) Disconnect the connector [3] to remove the waste-full photosensor
PCB [4].
(5)Removing the Waste Full LED PCB
1) Remove the screw [1].
2) Disconnect the connector [2] to remove the waste-full LED PCB [3].
2) Disconnect the connector [2] to remove the waste-full LED PCB [3].
[1]
[3]
[2]
[8]
[4]
[5]
[7]
[6]
[11]
[10]
[9]
[2]
[1]
[4]
[3]
[2]
[1]
[3]
AR-F13 MAINTENANCE 6-1
[6] MAINTENANCE
1. Maintenance System Table
A. AR series
B. DM series
2. Punch dust process (with the punch unit installed)
1) Pull the grip of the saddle finisher and move it to allow a space
between the machine and the saddle finisher.
2) Slow pull down the punch dust box and remove punch dust. Use a
polyethylene bag, etc. not to disperse punch dust.
3) Replace the punch dust box to the original position.
4) Move the saddle finisher back to the machine.
Check (Clean, replace, or adjust as necessary.)
Clean
Replace
Adjust
Lubricate
Move position
Unit name
Part name
When
calling
50K
100K 150K 200K 250K 300K 350K 400K
Remark
Transport section
Transport rollers
Transport paper
guides
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Staple un
Replace UN at 100K staple.
Staple cartridge
User replacement for every 5000pcs.
Unit name
Part name
When
calling
50K
100K 150K 200K 250K 300K 350K 400K
Remark
Transport section
Transport rollers
Transport paper
guides
guides
Drive section
Gears
(Specified position)
Belts
Other
Sensors
Discharge brush
Staple un
Replace UN at 100K staple.
Staple cartridge
User replacement for every 3000pcs.
AR-F13 MACHINE OPERATION 7-1
[7] MACHINE OPERATION
1. Staple sort mode
Collated sets of printouts are stapled and delivered to the offset tray (upper tray). Alternatively, printed paper is stapled at the center and delivered to
the saddle stitch tray (lower tray). The relation among stapling positions, orientation, paper size for stapling, and stapling capacity is shown below.
A. Saddle stitch function
Printed paper is stapled at two positions at the center and is folded in two
with the center down before delivery.
B. Punch function (only if a punch module is installed)
If the saddle stitch finisher is equipped with a punch module, printed
paper can be punched (two holes) and delivered to the offset tray. The
saddle stitch function and the punch function cannot be used together.
Stapling positions
Rear corner of
printouts
printouts
Center left two
positions of
printouts
positions of
printouts
Front corner of
printouts
printouts
Portrait orientation
Landscape orientation
Available paper sizes: 8-1/2"
x 11", A4 and B5
Stapling capacity: Up to 50
sheets for any sizes
x 11", A4 and B5
Stapling capacity: Up to 50
sheets for any sizes
Same as above
Same as above
Available paper sizes: 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2"
x 11" R, A3, B4, A4R, and B5R
Stapling capacity: Up to 50
sheets for 8-1/2" x 11"R, A4R
and B5R, and up to 25 sheets
for other sizes
8-1/2" x 14", 8-1/2" x 13", 8-1/2"
x 11" R, A3, B4, A4R, and B5R
Stapling capacity: Up to 50
sheets for 8-1/2" x 11"R, A4R
and B5R, and up to 25 sheets
for other sizes
Same as above
Same as above
Saddle stitch
Saddle stitch stapling cannot
be performed in the portrait
orientation.
be performed in the portrait
orientation.
Available paper sizes: 11" x
17", 8-1/2" x 11"R, A3, B4,
and A4R
Stapling capacity: Up to 10
sheets for any sizes
17", 8-1/2" x 11"R, A3, B4,
and A4R
Stapling capacity: Up to 10
sheets for any sizes
<Example>
<Example>
{Original 1}
{Punch positions}
{Original 2}
{Punch positions}
Click on the first or last page to see other AR-F13 (serv.man2) service manuals if exist.