Sharp AR-F13 (serv.man2) Service Manual ▷ View online
AR-F13 DISASSEMBLY AND ASSEMBLY 5-10
4) Push up the stack delivery roller (upper) [4] from below to free the
stack deliver roller (upper) [4] from the shaft [5].
5) Shift up the stack delivery roller (upper) [4], and then push it down to
detach the stack deliver roller (upper) [4].
6) Likewise, remove the stack delivery roller (upper) [6] at the front.
(11) Removing the Paddle
1) Remove the paddle assembly. (See 1.B.(4).)
2) Place the paddle assembly [1] as shown.
2) Place the paddle assembly [1] as shown.
3) Turn the gear [2] in the direction of the arrow to move up the stack
delivery roller assembly (upper) [3].
4) Push up the safety guide [4] from below to free one side of the safety
guide [4] from the shaft [5].
5) Push up the safety guide [4] from below to free the safety guide [4]
from the shaft [5].
6) Remove the paddle [6] in the direction of the arrow.
7) Likewise, remove the other paddle.
[4]
[5]
[4]
[6]
[1]
[3]
[2]
[4]
[5]
[4]
[5]
[1]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-11
(12)Removing the Stack delivery roller (lower)/Delivery Belt
1) Remove paddle assembly, and separate it from the processing tray
assembly. (See 1.B.(4).)
2) Slide the aligning plate (front) [2] and the aligning plate (rear) [3] of
the processing tray assembly [1] by sliding them to the outside.
3) Remove the processing tray stopper [4].
4) Remove the screw [5], and detach the paper guide (front) [7] while
freeing the two claws [6].
5) Remove the screw [8]; then, while freeing the claw [9], detach the
paper guide (rear) [10].
6) Remove the two stop rings [11]; then, move the two bushings [12] to
the inside.
7) Remove the four screws [13]; then, lift the stack delivery roller
assembly (lower) [14] to detach.
8) Remove the stack delivery roller (lower) [15] and the two delivery
belts [16].
NOTE: Be sure to mount them so that the edges [17] of the claws of the
delivery belts are flush.
[1]
[3]
[2]
[4]
[5]
[7]
[6]
[8]
[10]
[9]
[11]
[11]
[12]
[12]
[14]
[13]
[13]
[16]
[15]
[17]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-12
C. PCBs
(1)Removing the Finisher Controller PCB
1) Remove the rear cover. (See 1.A.(3).)
2) Disconnect the 17 connectors [1], and remove the screw [2].
2) Disconnect the 17 connectors [1], and remove the screw [2].
3) Free the PCB retainer [3], and detach the finisher controller PCB [4].
(2)Removing the Slide Home Position PCB
1) Open the front door [1], and turn the tab [2] on the stapler slide in the
direction of the arrow to slide the stapler to the frontmost point.
2) Remove the stapler unit. (See 1.B.(1).)
3) Place the stapler unit [3] as shown.
4) Remove the two screws [4], and detach the guide [5].
5) Turn the tab [2] on the stapler side in the direction of the arrow so
that that the fixing screw [7] of the slide home position PCB [6] is in
view through the round hole.
6) Remove the fixing screw [7].
7) Disconnect the connector [8].
8) Remove the flexible cable retainer [9].
9) Free the lock [10] of the connector in the direction of the arrow; then,
detach the flexible cable [11], and then detach the side home
position PCB [12].
[2]
[1]
[1]
[4]
[1]
[3]
[1]
[2]
[4]
[5]
[4]
[3]
[2]
[6]
[7]
[12]
[8]
[10]
[11]
[9]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-13
2. Punch Unit (AR-PN1)
A.Punch Driving System
(1)Removing the Punch Motor
1) Remove the two screws [1].
2) Disconnect the connector [2] to remove the punch motor [3].
(2)Removing the Horizontal Registration Motor
1) Disconnect connector [1].
2) Remove the harness [3] from the harness guide [2].
3) Remove the two screws [4] to remove the horizontal registration
3) Remove the two screws [4] to remove the horizontal registration
motor [5].
(3)Removing the Punch Unit
1) Remove the waste case.
2) Remove the screw [1] to detach the jam processing cover [2].
3) Disconnect the connector [3]
4) Remove the harness [5] from the harness guide [4].
4) Remove the harness [5] from the harness guide [4].
5) Disconnect the connector [6].
6) Remove the screw [7] and sensor support plate [8].
6) Remove the screw [7] and sensor support plate [8].
7) Remove the screw [9] and washer [10].
8) Disconnect the connector [11].
9) Remove the two screws [12] to detach the base cover [13].
9) Remove the two screws [12] to detach the base cover [13].
[2]
[1]
[3]
[4]
[5]
[2]
[1]
[3]
[2]
[1]
[3]
[5]
[4]
[6]
[7]
[8]
[13]
[9]
[10]
[12]
[11]
Click on the first or last page to see other AR-F13 (serv.man2) service manuals if exist.