Sharp AR-F13 (serv.man2) Service Manual ▷ View online
AR-F13 DISASSEMBLY AND ASSEMBLY 5-6
(4)Removing the Saddle Unit
1) Remove the front cover. (See 1.A.(2).)
2) Remove the rear cover. (See 1.A.(3).)
3) Open the jam removal cover [1]; then, remove the two screws [2] and
3) Open the jam removal cover [1]; then, remove the two screws [2] and
the right stay [3].
4) Turn the fold jam releasing dial assembly [4] to move the paper
retaining plate assembly [5] to the inside.
5) Remove the stop ring [6], and detach the timing belt [7].
6) Disconnect the two connectors [8].
7) Remove the three screws [9], and slide out the stapler unit [10]
slightly to the front.
8) Slide out the saddle unit [11] to the front.
(5) Removing the Processing Tray Assembly
1) Remove the processing tray upper cover. (See 1.A.(5).)
2) Remove the side guide. (See 1.A.(7).)
3) Remove the two screws [1], and disconnect the five connectors [2].
3) Remove the two screws [1], and disconnect the five connectors [2].
4) Pull the processing stopper base [3] to the front, and free the claw [5]
at the front and the claw [6] at the rear of the processing stopper [4].
5) Disconnect the three connectors [7].
6) Release the two claws [8] of the harness retainer, and detach the
motor harness [9].
[3]
[2]
[1]
[2]
[5]
[4]
[6]
[7]
[8]
[10]
[9]
[9]
[11]
[1]
[1]
[2]
[2]
[2]
[6]
[4]
[5]
[4]
[3]
[9]
[8]
[7]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-7
7) Remove the stop ring [10], and detach the timing belt [11].
8) Disconnect the connector [12], and free the harness [14] from the
8) Disconnect the connector [12], and free the harness [14] from the
edge saddle [13].
9) Remove the two screws [15], and slide the processing tray assembly
[16] to the rear; then, lift it to detach.
(6) Removing the Paddle Assembly
1) Remove the processing tray assembly. (See 1.B.(3).)
2) Place the processing tray assembly [1] as shown.
NOTE: Be sure to take care not to damage the aligning plate [2].
NOTE: Be sure to take care not to damage the aligning plate [2].
3) Detach the timing belt [3], and remove the two screws [4].
4) Separate the processing tray assembly [5] and the paddle assembly
[6] as shown.
[11]
[10]
[13]
[14]
[12]
[16]
[15]
[2]
[1]
[3]
[4]
[4]
[6]
[5]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-8
(7)Removing the Staple/Fold Drive Unit
1) Open the front door [1], and slide out the stapler unit [2] slightly to the
front.
2) Remove the screw [3], and detach the interface retainer [4].
3) Free the six harness retainers [5], and disconnect the connector [6].
4) Free the harness [7] from the harness retainer [5].
4) Free the harness [7] from the harness retainer [5].
5) Free the harness [7] from the edge saddle [8]; then, disconnect the
two connectors [9].
6) Release the harness retainer [10], and disconnect the connector
[11].
7) Free the harness [12] from the harness retainer [10].
8) Free the harness [12] for the edge saddle [13]; and disconnect the
two connectors [14].
9) Remove the screw [15], and free the claw [17] of the harness guide
from the long angle [16] of the base plate.
10) Disconnect the two connectors [18], and free the harness [20] from
the edge saddle [19].
11) Remove the three screws [21].
12) Remove the screw [22], and detach the staple/fold drive unit [23].
[1]
[2]
[6]
[7]
[3]
[7]
[8]
[9]
[7]
[5]
[5]
[4] [5] [7] [5]
[12]
[11]
[10]
[13]
[14]
[17]
[15]
[16]
[18]
[18]
[19]
[20]
[21]
[21]
[21]
[22]
[23]
AR-F13 DISASSEMBLY AND ASSEMBLY 5-9
(8)Removing the Feed Motor Unit
1) Remove the rear cover. (See 1.A.(3).)
2) Open the harness retainer [1], and disconnect the two connectors [2].
3) Remove the screw [3], and detach the harness guide [4].
3) Remove the screw [3], and detach the harness guide [4].
4) Remove the three screws [5], and detach the feed motor unit [6].
(9)Removing the Feed Roller
1) Remove the upper cover. (See 1.A.(4).)
2) Remove the upper right cover assembly. (See 1.A.(6).)
2) Remove the upper right cover assembly. (See 1.A.(6).)
3) Remove the feed motor unit. (See 1.B.(6).)
4) Remove the screw [1].
5) Remove the stop ring [2], and detach the bushing [3].
5) Remove the stop ring [2], and detach the bushing [3].
6) Remove the two screws [4].
7) Remove the gear [5], and detach the gear [6] while spreading the
claw.
8) Remove the stop ring [7], and detach the bushing [8].
9) Remove the screw [9], and detach the inlet sensor [10].
10) Remove the lower paper guide [11].
10) Remove the lower paper guide [11].
11) Remove the feed roller [12].
(10)Removing the Stack delivery roller (upper)
1) Remove the paddle assembly. (See 1.B.(4).)
2) Place the paddle assembly [1] as shown.
2) Place the paddle assembly [1] as shown.
3) Turn the gear [2] in the direction of the arrow to move up the stack
delivery roller assembly (upper) [3].
[5]
[5]
[3]
[4]
[6]
[1]
[2]
[2]
[1] [3]
[4]
[11]
[9]
[10]
[7]
[6]
[8]
[5]
[12]
[1]
[3]
[2]
Click on the first or last page to see other AR-F13 (serv.man2) service manuals if exist.