DOWNLOAD Sharp AR-C330 (serv.man5) Service Manual ↓ Size: 19.68 MB | Pages: 127 in PDF or view online for FREE

AR-C330  CONSUMABLE PARTS  3 - 5

The recommendable color print paper is shown below.

Use of the recommendable paper provides the best copy quality.

The standard paper follows it.

When paper of low white level is used, normal copy quality (color
reproduction) may not be obtained.

For OHP sheet, be sure to use the specified one.

For monochrome print, the following specifications serve as the
criteria of applicable or not.

(Values are under 20 ± 1°C, 65 ± 2%RH)

(*) Standard dimensions are as follows:

B5 (182 ± 1 x 257 ± 1mm)

B6 (128 ± 1 x 182 ± 1mm)

A4 (210 ± 1 x 297 ± 1mm)

A5 (148 ± 1 x 210 ± 1mm)

A6 (105 ± 1 x 148 ± 1mm)

8.5" ± 5/128 x 14" ± 5/128 inch

8.5" ± 5/128 x 11" ± 5/128 inch

8.5" ± 5/128 x 8.5" ± 5/128 inch

8.5" ± 5/128 x 13" ± 5/128 inch

(Paper which cannot be used)

The following paper cannot be used for printing.

• Paper with coated surface

• Paper with rough surface, or too smooth surface

• Documents which are separated from a pasted book

• Broken paper, folded paper, embossed paper, dry paper, wet

paper, curled paper

• Paper with metal tab or clip

• Paper with holes, cutout, or perforations

Kind

Model

Supplier

Specification

Note

Recommend 
paper

Hammermill 
LASER PRINT

Hammermill [11 x 8.5", 90g/m²]

[11 x 17", 90g/m²]

Neusiedler 
Color Copy 
(90g/m²)

Neusiedler

[A4, 90g/m²]
[A3, 90g/m2]

Standard paper

Necosa

Necosa

[11 x 8.5", 75g/m²]
[11 x 17", 75g/m²]

Hammermill 
DP

Hammermill [11 x 8.5", 75g/m²]

[11 x 17", 75g/m²]

Igepa

Igepa

[A4, 80g/m²]
[A3, 80g/m²]

OHP sheet 
(Specified paper)

BG74.6

FOREX

A4 size, 140g/m2

Made by 
FOLEX

Item

Standard paper

Applicable paper

Weight

60 - 90g/m²

60 - 120g/m²

Smoothness

Front: 

≥

 20s

Back : 

≥

 20s

(BEEK method)

Front: 

≥

 20s

Back : 

≥

 18s

(BEEK method)

Vesicularity

≥

 7s (BEEK method)

Same as the left.

Opaqueness

≥

 77%

Same as the left.

Surface resistance

1 x 10

10

 – 5 x 10

10

 

Ω

 cm

(20 ± 1°C, 65 ± 2%RH)

≥

 5.0 x 10

8

 

Ω

 cm

(20 ± 1°C, 65 ± 2%RH)

Hardness

Vertical: 

≥

 17cm

Horizontal: 

≥

 13cm

(CLARK method)

Same as the left.

Water content

4.5 % – 7.0%

Same as the left.

Thickness

75 

µ

m – 110 

µ

m

Same as the left.

Dimensions

Standard ± 1mm (*)

Same as the left.

Max. change: Temperature 15°C/hour,

Relative humidity 15%RH/hour, without dew

Temperature 

(min)

Humidity 

(min)

Temperature 

(mid)

Humidity 

(mid)

Temperature 

(max)

Humidity 

(max)

Period

–5°C

10%

40°C

90%

—

Max. change: Temperature 15°C/hour,

Relative humidity 15%RH/hour, without dew

Temperature 

(min)

Humidity 

(min)

Temperature 

(mid)

Humidity 

(mid)

Temperature 

(max)

Humidity 

(max)

Period

–5°C

10%

40°C

90%

—

Temperature 

(min)

Humidity 

(min)

Temperature 

(mid)

Humidity 

(mid)

Temperature 

(max)

Humidity 

(max)

Period

15°C

20%

30°C

80%

35°C

60%

—

RH

90%

10%

-5˚C

40˚C

40˚C, 90%

Humidity

Temperature

RH

90%

10%

-5˚C

40˚C

40˚C, 90%

Humidity

Temperature

RH

80%

20%

15˚C

35˚C

30˚C, 80%

35˚C, 60%

(Unsealed condition)

Humidity

Temperature

AR-C330  SETUP  4 - 1

Before installation of the machine, check the installing (using) envi-
ronment as follows:

If the installing environment does not satisfy the following condi-
tions, the machine may not display its performance fully, and may
result in troubles, causing safety problems. If the environment is
not satisfactory, arrange it before installation and setup of the
machine. 

If the door size is too small to deliver the machine in, delivery can-
not be made. Check the delivery space in advance.

Allow the following installation space around the machine for
proper operations and performances.

The space for options must be also considered.

Allow enough space at the back of the machine. If the back space
is insufficient, heat radiation and the dust proof function are pre-
vented, suppressing the machine performances and causing trou-
ble.

If the power source requirements are not satisfied, the machine can
not display full performances, causing troubles.

Be sure to follow the instructions below.

1) Power source capacity

Check that the power capacity is enough as specified below. If
is insufficient, it must be corrected.

Current capacity

2) Power voltage

Measure the power voltage during copying to check that it is
within the range of the rated voltage ±10%.

If the voltage is not within the above range, use wider wires to
reduce impedance. (Electrical work is required.)

There is a method to use a step-up transformer. In this case,
use the transformer of greater capacity than the machine's
max. power consumption.

3) Power frequency, waveform

The frequency fluctuation must be the specified level ±2%. If
the power waveform is distorted, trouble may be caused.

4) Safety

Be sure to ground the machine.

5) Power plug

Check the shape of the power plug. Do not use a plug of differ-
ent shape.

The machine is heavy, and options add further weight. Be sure to
check the floor strength for safety.

If the machine is not leveled properly, the toner concentration con-
trol is not performed properly, affecting copy quality adversely.

It may cause color shift or image distortion.

1) Temperature, humidity

The operation of this machine is assured under the following
conditions of storage (temperature, humidity).
Especially when the humidity is too high, paper absorbs mois-
ture to cause paper jams and dirty copy.

(Do not install near a stove, a humidifier, or a cooler.)

Do not install the copier near a heater, a cooler, or a humidifier.
If installed, the copier may form dew and cause troubles. Be
careful of ventilation, too.

2) Dust

If dust enters the copier, dirty copy, paper jams, and short life-
time.

No.

Content

1

Delivery space

2

Installing space

3

Power specifications (Capacity, fluctuation, safety)

4

Floor strength

5

Direct sunlight, dust, temperature, humidity, gases, 
chemicals

EX100V:

15A or above

EX200V:

10A or above

11-13/16"
(30 cm)

23-5/8"
(60 cm)

23-5/8"

(60 cm)

11-13/16"

(30 cm)

Humidity

85%

60%

20%

15

30

35

AR-C330  SETUP  4 - 2

3) Direct sunlight

If the copier is exposed to direct sunlight, the external section
may be discolored, causing poor copy quality.

4) Gases and chemicals

Do not install the copier near gases and chemicals. Especially
be careful of a diazo-type copier, which may produce ammo-
nium gas. The copy quality may be adversely affected, causing
troubles.

5) Vibrations

Do not install machines which produce vibrations around the
copier. If vibrations are applied to the copier, copies may be
blurred and troubles may be caused.

It is advisable to use a forklift for efficiency and safety.

If a forklift is not available, six persons are required to move the
machine. The copier is very heavy. Consider safety in delivery and
installation work.

The copier must be transported in the packed condition to the
installing site (building).

Remove the copier from the packing case outside the installing
building, then carry it inside the building.

Unpack in the following procedures.

1) Remove the PP band.

2) Remove the top case and the packing case.

3) Remove the internal packing material and packed items.

4) Remove the machine.

No.

Content

Method

1

Facility, equipment, 
man power

Use a forklift. (If a forklift is not 
available, 4 persons are required to 
install.)

2

Delivery form

Transported in packed conditions.

1

PP band

8

Bottom case unit

2

Top case

9

Accessory unit

3

Packing case

10

Paper exit tray AS

4

Skid unit

11

Accessory sleeve

5

Top pad R

12

Waste toner bottle

6

Top pad L

13

Operation Manual

7

Polyethylene bag

–

–

AR-C330  SETUP  4 - 3

3

5

6

7

8

4

2

9

10

11

13

12

No.

Name

Content

1

Oil bottle

AR-C15SL

2

Developer cartridge (Y) Color developer kit (Y, M, C)

Black developer (K)

3

Developer cartridge (M)

4

Developer cartridge (C)

5

Developer cartridge (K)

6

Developing unit

AR-DW1N
(Developing unit x 4)

Toner

Y, M, C, K