Sharp AR-C200P (serv.man3) Handy Guide ▷ View online
Message
Cause
Error Description
Solutions
Open top cover
389: Paper jam
389: Paper jam
Check MP tray
390: Paper jam
390: Paper jam
Check tray *
391~395:
Paper jam
391~395:
Paper jam
Open top cover
400: Paper
size error
400: Paper
size error
Refill toner
410: Yellow
411: Magenta
412: Cyan
413: Black
410: Yellow
411: Magenta
412: Cyan
413: Black
Remove paper
480: Stacker
full
480: Stacker
full
Set ***
490: No paper
in MP tray
(* stands for A4
B4, etc.)
490: No paper
in MP tray
(* stands for A4
B4, etc.)
Set ***
491~495: No
paper in * tray
(* stands for A4
B4, etc.)
491~495: No
paper in * tray
(* stands for A4
B4, etc.)
Replace fuser
Paper in * tray
nearly empty
nearly empty
Disk operation
error
error
Jam generated in paper
path.
path.
Paper jam during paper
feed from MT.
feed from MT.
Paper jam detected
between cassette and
black ID.
between cassette and
black ID.
Non-set paper (45mm
or above) detected by
printer engine.
or above) detected by
printer engine.
Certain toner is almost
empty.
empty.
Paper ejection stacker
is full.
is full.
No paper in selected
cassette. cassette is
not set, or paper ran
out in cassette being
used.
cassette. cassette is
not set, or paper ran
out in cassette being
used.
Paper empty in
cassette 1, 2, 3, 4, or 5.
cassette 1, 2, 3, 4, or 5.
Fuser counter
exceeded life.
exceeded life.
Paper near end
detected.
detected.
Cannot write in HDD.
Open front cover and check jammed paper.
Check for miss-fed paper around MT
cassette.
cassette.
1) Check jammed paper between cassette
and yellow ID.
2) Check if paper entry switch is normal.
and yellow ID.
2) Check if paper entry switch is normal.
1) Is paper custom size?
2) Is paper standard size?
2) Is paper standard size?
1) Selected toner cartridge is almost empty.
2) Check if selected toner cartridge is
normal.
2) Check if selected toner cartridge is
normal.
1) Check if stacker is full.
2) Check if stacker full sensor is operating
properly.
2) Check if stacker full sensor is operating
properly.
1) Check if paper is empty in MT.
2) Check if paper-end sensor is operating
properly.
2) Check if paper-end sensor is operating
properly.
1) Check if paper is empty in selected
cassette.
2) Check if paper-end sensor is operating
properly.
cassette.
2) Check if paper-end sensor is operating
properly.
1) Is error message displayed?
2) Was fuser unit just replaced?
2) Was fuser unit just replaced?
Are only few papers remaining in tray?
(approx. 30 sheets or less)
(approx. 30 sheets or less)
Is faulty operation being applied?
Yes
Yes
No
Yes
No
Yes
Yes
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
No
Yes
Remove jammed paper.
Remove miss-fed paper and close
cover.
Check/replace MT.
cover.
Check/replace MT.
Remove jammed paper.
Replace entry switch.
No treatment required.
Adjust paper size guide in cassette.
Replace paper size board (PXC PWB).
Adjust paper size guide in cassette.
Replace paper size board (PXC PWB).
Replace with new toner kit.
Replace selected toner sensor.
Replace selected toner sensor.
Remove paper from stacker.
Replace stacker full sensor.
Replace stacker full sensor.
Set paper in MT.
Replace paper-end sensor.
Replace paper-end sensor.
Set paper in selected cassette.
Replace the corresponding paper-end
sensor.
Replace the corresponding paper-end
sensor.
Check fuser unit life.
Replace fuser immediately or at next
maintenance.
Replace fuser immediately or at next
maintenance.
Refill paper.
Check paper near end sensor.
Check paper near end sensor.
Check manual operation.
HDD abnormality. Replace HDD.
HDD abnormality. Replace HDD.
NOTES
30
Version 1
June 2004
NOTES
31
Version 1
June 2004
Version 1
June 2004
