Sharp AR-C200P (serv.man3) Handy Guide ▷ View online
FIRMWARE REVISION
17
Version 1
June 2004
PU
Version
00.01.05
Production
Level
NOTE: The PU version can be discovered using either of the following methods.
1)
In the ‘On-Line’ state, press and hold the ‘TEST’ Button on the NIC panel (rear frame)
for 5 seconds and release. The menu map will be printed.
for 5 seconds and release. The menu map will be printed.
The PU version is line three on page one.
OR
OR
2)
Enter System Maintenance Menu by turning on the power supply switch while holding
down the [Menu]+[Item]+[Value]+[Cancel] (0+1+6+7)switches.
down the [Menu]+[Item]+[Value]+[Cancel] (0+1+6+7)switches.
Press the Menu button until Diagnostic Mode is displayed. PU version is displayed on
the second line of the LCD display.
the second line of the LCD display.
SIMULATIONS
18
Version 1
June 2004
This section refers to the system maintenance menu only
For Diagnostic Mode Please refer to the Service Manual
System Maintenance MENU
The printer enters this mode when you turn on the power supply switch while holding down the
[Menu]+[Item]+[Value]+[Cancel] (0+1+6+7)switches.
Note: This menu is not disclosed to end-users because changes can be made to
brand/destination, etc.
SIMULATIONS
19
Version 1
June 2004
Category
Item(1st Line)
Value(2nd Line)
DF
Functions
USER
USER
ODA
OEL
APS
JP1
JPOEM1
OEMA
OEML
OEL
APS
JP1
JPOEM1
OEMA
OEML
* Sets
Brand
JPOEM1: Japan OEM
OEMA: Overseas OEM for
A4 default
OEML: Overseas OEM for
Letter default
Boots up automatically when
the Menu is existed.
OEMA: Overseas OEM for
A4 default
OEML: Overseas OEM for
Letter default
Boots up automatically when
the Menu is existed.
CONFIGURATION
MENU
MENU
ENGINE
SPEED
SPEED
HIGH
LOW
LOW
*
For switching the engine
speed between the
overseas 16/24PPM model
and the 20/24PPM
model.
speed between the
overseas 16/24PPM model
and the 20/24PPM
model.
HIGH
RESOLUTION
ENABLE
DISABLE
DISABLE
*
Not used.
note: Don’t change the
setting value.
note: Don’t change the
setting value.
ENG STATUS
PRINT
ENG STATUS
PRINT
EXECUTE
Selecting by the Select
switch, then
pressing the On-line switch
will prompt
initialization and printing
Engine information.
switch, then
pressing the On-line switch
will prompt
initialization and printing
Engine information.
PAGE CNT PRINT
PAGE CNT
PRINT
ENABLE
DISABLE
DISABLE
*
Sets printing or not printing
the total page count
in PRINT MENU MAP.
the total page count
in PRINT MENU MAP.
SIMULATIONS
20
Version 1
June 2004
PCL
ENABLE
DISABLE
DISABLE
*
IBM PPR III XL
ENABLE
DISABLE
DISABLE
*
EPSON FX
ENABLE
DISABLE
DISABLE
*
Adobe
Postscript
Postscript
ENABLE
DISABLE
DISABLE
*
HP-GL/2
ENABLE
DISABLE
DISABLE
*
PCL XL
ENABLE
DISABLE
DISABLE
*
PERSONALITY
PDF
ENABLE
DISABLE
DISABLE
*
Change the default PDL for
each brand.
PDLs that are disabled in this
Menu will not be displayed on
User Menu or Admin Menu’s
PERSONALITY.
When print data in the PDL
language set to DISABLE is
received, the printer will
display INVALID DATA and
discard received data.
(HPGL/2 is under
development, and there is no
plan to implement as yet in
the product. ) The PDF
function requires Adobe
Postscript; thus, switching
ON/OFF of PDF alone is
disabled. (Setting Adobe
Postscript on DISABLE will
set the PDF function to
DISABLE as well. ) On the
PX711/713, neither Adobe
Postscript nor PDF can be
set to DISABLE. (They are to
be always set to ENABLE for
use. Even if they are set to
DISABLE, the printer
processes the data it
receives.
each brand.
PDLs that are disabled in this
Menu will not be displayed on
User Menu or Admin Menu’s
PERSONALITY.
When print data in the PDL
language set to DISABLE is
received, the printer will
display INVALID DATA and
discard received data.
(HPGL/2 is under
development, and there is no
plan to implement as yet in
the product. ) The PDF
function requires Adobe
Postscript; thus, switching
ON/OFF of PDF alone is
disabled. (Setting Adobe
Postscript on DISABLE will
set the PDF function to
DISABLE as well. ) On the
PX711/713, neither Adobe
Postscript nor PDF can be
set to DISABLE. (They are to
be always set to ENABLE for
use. Even if they are set to
DISABLE, the printer
processes the data it
receives.
NETWORK
The details depend on
Network.
( Not used )
Network.
( Not used )
DIAGNOSTIC
MODE
XX.XX.XX
MODE
XX.XX.XX
Refer to Service Manual Page 80
for more detail
Enters engine self-diagnostic
mode.
The display in place of xx.xx
varies among the
PU version.
(The display within this
category depends on the
Engine Maintenance specs.)
mode.
The display in place of xx.xx
varies among the
PU version.
(The display within this
category depends on the
Engine Maintenance specs.)
Click on the first or last page to see other AR-C200P (serv.man3) service manuals if exist.