Sharp AR-5316E (serv.man8) User Manual / Operation Manual ▷ View online
11
BEFORE USING THE MACHINE
1
PAPER SIZE indicators
Light up to show the selected copy paper size. (p.16)
PAPER SIZE ENTER key (
)
Use to set the paper size in the paper trays. (p.16)
SPF indicator (when the SPF is installed)
Lights up when originals are set in the document
feeder tray. (p.19)
feeder tray. (p.19)
TRAY SELECT key (
)
Use to manually select a paper tray. (p.21)
AUTO IMAGE key (
) / indicator
Press for automatic copy ratio selection. (p.22)
Paper feed location / misfeed location
indicators
indicators
The selected paper feed location is shown by a lit
indicator (
indicator (
). (p.18)
The general location of misfed paper is shown by a
blinking red indicator (
blinking red indicator (
). (p.47)
PRESET RATIO selector keys (
,
)
/ indicators
Use to select preset reduction/enlargement copy
ratios. (p.23)
ratios. (p.23)
Numeric keys
Use to select the desired copy quantity or to make
user program entries. (p.22)
To display the total number of pages output by the
machine, hold the [0] key down. (p.55)
user program entries. (p.22)
To display the total number of pages output by the
machine, hold the [0] key down. (p.55)
[
] key
Use to check the total number of copies made.
(p.55)
(p.55)
START key (
) /indicator
Press to make a copy (p.18). Also press to exit
"Auto power shut-off" mode and to set a user
program. Copying is possible when the indicator is
on.
"Auto power shut-off" mode and to set a user
program. Copying is possible when the indicator is
on.
CLEAR ALL key (
)
Clears all selected settings and returns the
machine to the initial settings. (p.12)
machine to the initial settings. (p.12)
CLEAR key (
)
Clears the copy quantity display or terminates a
copy run.
copy run.
16
17
18
19
20
AUTO
%
21
22
23
24
25
26
27
INTERRUPT
ZOOM
1 3 5
25 400%
AUTO
ENTER
AUTO
ACC.#-C
AUTO
%
A3
A4
A4
A5
B4
A4
A4
A5
B4
EXTRA
200%
50%
141
86
81
70
70
122
115
100%
(Two-tray model only)
Not used for this machine.
4
5
6
7
8
9
10
11
12
14
15
16 17 18 19
20
21
22
23
24
25
26 27
13
AR-5316-5320-EX.book 11 ページ 2003年11月26日 水曜日 午後5時3分
12
POWER ON AND OFF
The power switch is located on the left side of the machine.
POWER ON
Turn the power switch to the "ON"
position.
position.
It will take about 45
seconds for the machine
to warm up. While the
machine is warming up,
the POWER SAVE
indicator (
seconds for the machine
to warm up. While the
machine is warming up,
the POWER SAVE
indicator (
) will blink.
(The POWER SAVE
indicator (
indicator (
) will go off
when the machine is
ready to copy.)
ready to copy.)
However, you can make desired settings and press
the [START] key (
the [START] key (
) during warm-up. Copying will
start after warm-up.
POWER OFF
Make sure that the machine is not in
operation and then turn the power switch
to the "OFF" position.
operation and then turn the power switch
to the "OFF" position.
If the power switch is
turned off while the
machine is in operation,
a misfeed may occur and
the job that was in
progress will be
cancelled.
turned off while the
machine is in operation,
a misfeed may occur and
the job that was in
progress will be
cancelled.
Check the following to make sure the machine is not in
operation:
• The START indicator is lit. (Initial state)
• The POWER SAVE indicator (
operation:
• The START indicator is lit. (Initial state)
• The POWER SAVE indicator (
) is lit. ("Preheat
mode" or "Auto power shut-off" mode)
Power Save Modes
Preheat mode
This function automatically switches the machine to a low power consumption state if the set duration of time
elapses without the machine being used when the power is on. The POWER SAVE indicator (
elapses without the machine being used when the power is on. The POWER SAVE indicator (
) lights up,
however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the
operation panel is pressed, an original is placed, or a print job is received.
operation panel is pressed, an original is placed, or a print job is received.
Auto power shut-off mode
This function automatically switches the machine to a state that consumes even less power than preheat mode if the
set duration of time elapses without the machine being used when the power is on. All lights except the POWER
SAVE indicator (
set duration of time elapses without the machine being used when the power is on. All lights except the POWER
SAVE indicator (
) and ON LINE indicator (
) go off. To resume normal operation, press the [START] key (
).
Normal operation also resumes automatically when a print job is received. While in auto power shut-off mode, no
keys (except the [START] key (
keys (except the [START] key (
)) can be used.
• The machine reverts to the initial settings when it is first turned on, when the [CLEAR ALL] key (
) is pressed,
or when no keys are pressed for the preset "Auto clear" time following the end of a copy job. When the machine
reverts to the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time
can be changed in the user settings. (p.33)
reverts to the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time
can be changed in the user settings. (p.33)
• The machine is initially set to automatically enter power save mode if not used for copying or printing, for a
preset period of time. This setting can be changed in the user programs. (p.33)
The machine has two power save modes to reduce overall power consumption thereby
reducing the cost of operation. In addition, these modes conserve natural resources and help
reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto
power shut-off mode".
reducing the cost of operation. In addition, these modes conserve natural resources and help
reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto
power shut-off mode".
The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is
suggested that you set times that are appropriate for your usage of the machine. (p.33)
suggested that you set times that are appropriate for your usage of the machine. (p.33)
Note
Note
Initial settings
The machine assumes the initial settings when it is first turned on, when the [CLEAR ALL] key (
) is pressed,
and approximately one minute after the last copy is made in any mode.
Copy ratio: 100%, Exposure: Automatic
Copy quantity: 0, All special copier modes: Off
Auto paper selection: On, Paper feed station: The tray selected in the "Default tray setting" in the user programs. (p.34)
Copy ratio: 100%, Exposure: Automatic
Copy quantity: 0, All special copier modes: Off
Auto paper selection: On, Paper feed station: The tray selected in the "Default tray setting" in the user programs. (p.34)
AR-5316-5320-EX.book 12 ページ 2003年11月26日 水曜日 午後5時3分
13
1
LOADING PAPER
The paper required indicator (
) will light up when there is no copy paper in the selected paper feed tray, or when
the selected paper tray is not installed or is improperly installed.
PAPER
For best results, use only SHARP recommended paper.
*
1
A5 (5-1/2" x 8-1/2") can be used in the upper paper tray but cannot be used in other trays.
*
2
When making a large number of copies or prints using 90 g/m
2
(24 lbs.) paper, remove the output from the paper output tray
when about 100 pages have been printed. The output may not stack correctly if more than 100 pages are allowed to
accumulate.
accumulate.
*
3
The number of sheets of the paper which can be set changes with the weight of a paper.
Special papers
Follow these guidelines when using special papers.
●
●
●
●
● Use SHARP recommended transparency film and label sheets. Using other than SHARP recommended
paper may result in misfeeds or smudges on the output. If other than SHARP recommended media must
be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or
printing).
be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or
printing).
●
●
●
● There are many varieties of special paper available on the market, and some cannot be used with this
machine. Before using special paper, contact your authorised service representative.
●
●
●
● Before using other than SHARP recommended paper, make a test copy to see if the paper is suitable.
Paper tray type
Paper type
Size
Weight
Capacity
Paper tray
Standard paper
Recycled paper
Recycled paper
A5*
1
A4
B4
A3
(5-1/2" x 8-1/2"*
B4
A3
(5-1/2" x 8-1/2"*
1
(Invoice))
(8-1/2" x 11" (Letter))
(8-1/2" x 13" (Foolscap))
(8-1/2" x 14" (Legal))
(11" x 17" (Ledger))
(8-1/2" x 13" (Foolscap))
(8-1/2" x 14" (Legal))
(11" x 17" (Ledger))
56 g/m
2
to 90 g/m
2
*
2
(15 lbs. to 24 lbs.
*
2
)
250 sheets
(Load paper lower
than the line on the
tray)
(Load paper lower
than the line on the
tray)
Bypass tray
Standard paper
Recycled paper
Recycled paper
A6R to A3
(5-1/2" x 8-1/2" (Invoice)
to 11" x 17" (Ledger))
(5-1/2" x 8-1/2" (Invoice)
to 11" x 17" (Ledger))
56 g/m
2
to 80 g/m
2
(15 lbs. to 20 lbs.)
100 sheets *
3
Thick paper
Max. 200 g/m
2
(54
lbs.)
Load one sheet of
these papers at a
time to the bypass
tray.
these papers at a
time to the bypass
tray.
Transparency film
Labels
Labels
Envelopes
International DL
(110 mm x 220 mm)
International C5
(162 mm x 229 mm)
Commercial 9
(3-7/8" x 8-7/8")
Commercial 10
(4-1/8" x 9-1/2")
(110 mm x 220 mm)
International C5
(162 mm x 229 mm)
Commercial 9
(3-7/8" x 8-7/8")
Commercial 10
(4-1/8" x 9-1/2")
5 sheets
AR-5316-5320-EX.book 13 ページ 2003年11月26日 水曜日 午後5時3分
14
BEFORE USING THE MACHINE
LOADING PAPER
Make sure that the machine is not copying or printing, and then follow these steps to load paper.
Loading the paper tray
1
Gently lift and pull out the paper tray
until it stops.
until it stops.
2
Push the pressure plate down until it
locks in place.
locks in place.
Push the centre of the
pressure plate down until
it locks into place.
pressure plate down until
it locks into place.
3
Fan the paper.
If the paper is not fanned,
double-feeds or misfeeds
may occur.
double-feeds or misfeeds
may occur.
4
Load paper into the tray.
5
Gently push the paper tray into the
machine.
machine.
• Do not load paper higher than the line on
the tray (up to 250 sheets).
• Make sure that the paper fits under the tabs
on the right side of the tray.
• Make sure the stack of paper is straight
before loading it. When adding paper, take
the remaining paper out and combine it into
a single stack with the new paper.
the remaining paper out and combine it into
a single stack with the new paper.
Note
If you loaded a different size of paper than
was loaded previously in the tray, go to
"CHANGING A TRAY’S PAPER SIZE
SETTING" (p.16).
was loaded previously in the tray, go to
"CHANGING A TRAY’S PAPER SIZE
SETTING" (p.16).
Note
AR-5316-5320-EX.book 14 ページ 2003年11月26日 水曜日 午後5時3分
Click on the first or last page to see other AR-5316E (serv.man8) service manuals if exist.