Sharp AR-163 (serv.man4) Service Manual ▷ View online
9) Select the data for MCU to be transferred.
10) Select the data for the electronic sort board to be transferred.
∗
When the electronic sort board is not installed, this procedure is
automatically canceled. Go to procedure 11).
automatically canceled. Go to procedure 11).
11) After transfer of data, turn off the machine and disconnect the con-
nector.
Reference: If the power is turned off during the procedure or in case
of a communication error, resume the procedure from 2).
2. PRINTER CONTROL PWB FIRMWARE
VERSION UP <With an option installed>
A. Cases where flash memory rewriting is required
In the following cases, the program in the printer control PWB flash
memory must be rewritten.
memory must be rewritten.
1) When a bug or other error is found
2) Data stored in the flash memory is destroyed or deleted.
3) When the flash memory is replaced.
2) Data stored in the flash memory is destroyed or deleted.
3) When the flash memory is replaced.
B. Necessary tools
1) Computer (PC) <Operates on MS-DOS.>
2) Parallel cable
3) Program data file (xxx.BIN)
2) Parallel cable
3) Program data file (xxx.BIN)
C. Procedure
1) Print the configuration list to check the firmware version.
Use the operation panel of the copier to perform the following pro-
cedure.
ONLINE <off line>
cedure.
ONLINE <off line>
→
MENU <Test Printing Menu>
→
ITEM
<Configuration Page>
→
ENTER <The test page prints>
2) Connect the PC and the copier with the parallel cable.
3) Turn on the power
4) Execute SIM 67-14.
3) Turn on the power
4) Execute SIM 67-14.
“Erase Flash Data?” is displayed on the LCD.
5) Press the ENTER key on the copier’s operation panel.
“Now Erasing” is displayed on the LCD.
6) After deletion of data, “Please Send Data” is displayed on the LCD
and the machine enters the ready state for data input.
7) Download the program file.
(Note) Never turn off the power during download.
Set the PC to DOS mode
→
Check that the display shows
READY.
→
Then type COPY /B xxx.BIN LPT1:
and press the enter key.
( : space)
( : space)
8) The machine enters the data reception mode.
While “Writing” is displayed on the LCD, data are written into the
flash ROM.
flash ROM.
9) When data reception and data writing into the flash ROM are
completed, the SUM check is automatically performed.
(Note) In case of an error, “Sum check Error” is displayed.
Turn off the power once, and repeat the procedures from 3).
10) If there is no problem on the result of the SUM check, “Complete”
is displayed on the LCD.
11) Turn off/on the power to print the configuration page with the
above procedures, and check the firmware version.
12) Perform printing on the PC side and check that printing is per-
formed normally.
AR-162 FLASH ROM VERSION UP PROCEDURE – 2
[13] ELECTRICAL SECTION
1. BLOCK DIAGRAM
MCU-PWB
CCD-PWB
APC-PWB
TRAY-PWB
ERDH-PWB
Mother-PWB
FAX-PWB
PCL-PWB
Tel/Liu-PWB
NW-CON-PWB
NIC-Board
SPF-SEN-PWB
SPF-CON-PWB
2ndCS-PWB
DEFOG-HEATER-PWB
HVU
Power
Supply
PS-FAN
PS-SW
Polygon-Motor
Mirror-Motor
Shifter-Motor
Job
Separator-Motor
SPF-Motor
SPF-CLH
SPF-RSOL
Dsub-25pin
SPF-GSOL
SPF-PSOL
L1
L2
Fuser-Lamp
Copy-Lamp
Defog-Heater
Down-Load-CON
PICK UP SOL1
FEED SOL1
PICK UP SOL2
Duplex-Motor
Toner-Motor
MAIN-Motor
THERMISTER
FAX-OP-PWB
OPERATION
PANEL
ERDH-OP-PWB
COPY-OP-PWB
LCD-OP-PWB
CASS1
PPD1
DRS1
CSS1
CASS2
PPD2
CASS:CS
UNIT
DETECTOR
CSS
:PAPER
DETECTOR
PPD
:PAPER
PASS
DETECTOR
DRS
:DOOR
DETECTOR
HAND PICK
UP
SOL
CN15
CN19
PS ROLLER SOL
CN18
CN10
CN36
CN13
CN12
BD-PWB
LSU-PWB
PAPER
SIZE
SENSOR
INCH
AB
CN4
CN8
CN9
CN7
CN3
CN31
CN6
CN5
CN11
FUSER
COOLING
FAN
CN23
CN24
CN25
CN34
CN20
CN35
CN2
CN1
SIDE COVER
CASETTE
SWITCH
SWITCH
CN14
CN22
DEV SENSOR
CN27
CASETTE PICK
UP
SOL
HAND PAPER EMPTY SENSOR
CASETTE PAPER EMPTY SENSOR
CN32
CN33
PAPER
IN
SENSOR
CN28
SCANNER HP SENSOR
SCANNER COVER SWITCH
CN29
CN17
DUPLEX PAPER
OUT
SENSOR
CN26
CN38
CRUM UNIT
AR-162 [13] ELECTRICAL SECTION 11/22/2000
AR-162 ELECTRICAL SECTION – 1
2. ACTUAL WIRING DIAGRAM
ACTUAL WIRING DIAGRAM 1/3
AR-162 [13] ELECTRICAL SECTION 11/22/2000
AR-162 ELECTRICAL SECTION – 2
ACTUAL WIRING DIAGRAM 2/3
AR-162 [13] ELECTRICAL SECTION 11/22/2000
AR-162 ELECTRICAL SECTION – 3
Click on the first or last page to see other AR-163 (serv.man4) service manuals if exist.