DOWNLOAD Sharp PN-L802B (serv.man12) Service Manual ↓ Size: 6.57 MB | Pages: 58 in PDF or view online for FREE

21

E

1. INPUT (Input mode selection)
The menu is displayed. Press 

 or 

 to select the input 

mode, and press 

 to enter.

*  You can select the input terminal by pressing the input

switch of the monitor.

PC D-SUB

PC D-sub input terminal

*1

Audio input terminal

PC HDMI

PC/AV HDMI input terminal

*2

*3

AV HDMI

PC/AV HDMI input terminal

*2

AV COMPONENT PC D-sub input terminal

*1

Audio input terminal

AV VIDEO

PC D-sub input terminal

*1

PC DVI-D

PC/AV DVI-D input terminal

*4

*3

PC HDMI

PC/AV HDMI input terminal

*2

PC D-SUB

PC D-sub input terminal

*1

PC RGB

PC RGB input terminals

*5

AV DVI-D

PC/AV DVI-D input terminal

*4

AV HDMI

PC/AV HDMI input terminal

*2

AV COMPONENT

AV COMPONENT input
terminals

*5

PC D-sub input terminal

*1

AV S-VIDEO

AV S-video input terminal

AV VIDEO

AV video input terminal
PC D-sub input terminal

*1

*1  Select the terminal to be used in D-SUB of INPUT

SELECT. (See page 26.)

*2  Select the terminal to be used in HDMI of INPUT SELECT.

(See page 26.)

*3  Select the terminal for AUDIO SELECT which is used for

audio input. (See page 26.)

*4  Select the terminal to be used in DVI of INPUT SELECT.

(See page 26.)

*5  Select the terminal to be used in BNC of INPUT SELECT.

(See page 26.)

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the

previous level.

Displays and turns off the menu screen. (see page 23.)

4. VOL +/- (Volume adjustment)
Pressing 

 or 

displays the VOLUME menu when the

menu screen is not displayed.

Press 

 or 

to adjust the volume of the sound.

*  If you do not press any buttons for about 4 seconds, the

VOLUME menu automatically disappears.

Pressing 

 or 

displays the BRIGHT menu when the

menu screen is not displayed.

Press 

 or 

to adjust the brightness.

*  If you do not press any buttons for about 4 seconds, the

BRIGHT menu automatically disappears.

The menu is displayed.
Press 

 or 

to select the screen size. (See page 22.)

Displays monitor information. When you press this button

again, the display disappears.

When the PN-ZB01 (optional) is attached, the display changes

from INFORMATION1 → INFORMATION2 → clear display,

and so on every time you press this button.

•  The display disappears automatically after about 15

seconds.

•

LAN

 is displayed during LAN communication.

•  If

LAN

 is displayed in red, there is a duplicate IP address.

Each time you press this button, the color mode changes in

the following order:

STD (Standard) → VIVID → sRGB → STD...

•  sRGB applies to PC input only.

 sRGB is international standard of color representation

specified by IEC (International Electrotechnical

Commission). Color conversion is made in taking account

of liquid crystal’s characteristics and represents color tone

close to its original image.

22

E

n

Even when the screen size is changed, the display may remain the same depending on the input signal.

PC input

Displays image so it fills the entire screen.

AV input

An image with a 4:3 aspect ratio is stretched to fill the entire

screen.

PC input

An image with a 4:3 aspect ratio is enlarged to fill the entire screen

without changing the aspect ratio. The edges of the image may be 

cut off.

AV input

PC input

Use this size if ZOOM 1 cuts off the subtitles.

AV input

PC input

Displays image so it fills the screen without changing the aspect

ratio of the input signals.

AV input

Displays the entire image of the aspect ratio of 4:3 without

changing the aspect ratio.

PC input

Displays the dots of the signals input from the connected PC as

the corresponding dots on the screen.

AV input

Displays the dots of the input signals as the corresponding dots on

the screen.

TIPS

•  Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial

or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright

Law, so please be careful.

•  When dual-screen display is selected, the screen size cannot be changed.

•  The appearance of the original video may change if you select a screen size with a different aspect ratio than the original

image (e.g. TV broadcast or video input from external equipment).

•  When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this

monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen 

size to “NORMAL”.

•  When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen

size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the

edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

•  Depending on the original image size, black bands may remain at the edges of the screen.

23

E

Video and audio adjustment and settings of various functions

are enabled. This section describes how to use the menu 

items. See pages 24 to 27 for details of each menu items.

Caution

•  Do not turn the main power switch off while the menu items

are being displayed. Doing so may initialize the settings.

n

(Adjusting CONTRAST in the PICTURE menu)
1.  Press 

MENU

1 9 2 0 x 1 0 8 0

V: 60 Hz    H: 67.5 kHz

1 9 2 0 x 1 0 8 0

V: 60 Hz    H: 67.5 kHz

▲

▲

▲

1 9 2 0 x 1 0 8 0

V: 60 Hz    H: 67.5 kHz

For items that have

 , press 

, make settings and then 

press 

MENU

.

MENU

TIPS

•  The menu will differ depending on the input mode.

•  The menu screen will close automatically if no operation is

performed for about 15 seconds. (DATE/TIME SETTING,

SCHEDULE and LAN SETUP screens will close in about 4

minutes.)

n

▲

▲

▲

1 9 2 0 x 1 0 8 0

V: 60 Hz    H: 67.5 kHz

1  Name of the menu

2  Input mode

3  An item being selected (highlighted)

4  Screen resolution of input signal, and other data.

TIPS

•  Items that cannot be selected appear in gray. 

(e.g. Function not supported by the current input signal)

n

The displayed menu items vary depending on whether or not 
the PN-ZB01 (optional) is attached.
The following menus will be displayed only when the PN-ZB01
(optional) is attached.

SETUP

HOT PLUG CONTROL DVI
RS-232C/LAN SELECT
LAN SETUP
AUTO ASSIGN FIXED IP ADDR.
SPEAKER SELECT

OPTION INPUT SELECT

DVI
BNC

AUDIO SELECT

PC DVI-D
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT (BNC)
AV COMPONENT (D-SUB)
AV S-VIDEO
AV VIDEO (BNC)
AV VIDEO (D-SUB)

PIP/PbyP PIP SOURCE

24

E

The menu will differ depending on the input mode.

n

You can move the menu screen display position each time 

DISPLAY

 is pressed.

AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically

adjusted.
Pressing 

 performs adjustment.

Use this automatic adjustment when you use the PC D-sub

input terminal or PC RGB input terminals to display a PC

screen for the first time or when you change the setting of

the PC. (See page 30.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.

Adjust when there is flickering in the form of vertical stripes.

When using the adjustment pattern (see page 30), make

adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.

Useful when small characters appear with low contrast and/

or there are flickers at corners.

When using the adjustment pattern (see page 30), make

adjustments so that no horizontal stripe noise appears in it.

*  Adjustments to PHASE should be made only after CLOCK

has been correctly set.

H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of

input signals is not recognized properly. (Adjustment may be

impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input 

signals is not recognized properly. (Adjustment may be

impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory

preset values.

Select “ON” and then press 

MENU

.

n

You can move the menu screen display position each time 

DISPLAY

 is pressed.

AUTO (PC D-SUB/PC RGB)
The ANALOG GAIN and ANALOG OFFSET are
automatically adjusted.
Pressing 

 performs adjustment.

ANALOG GAIN (PC D-SUB/PC RGB)
Adjusts the bright portions of the video input signal.
ANALOG OFFSET (PC D-SUB/PC RGB)
Adjusts the dark portions of the video input signal.
BRIGHT
Adjusts the backlight brightness. (In PIP mode, the main side

setting is reflected in the image.)
CONTRAST
Adjusts the difference between the bright and dark portions

of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards

green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
RGB INPUT RANGE (PC DVI-D/PC HDMI/PC D-SUB/PC

RGB/AV DVI-D/AV HDMI)
Sets the RGB input signal range. When using HDMI set to

AUTO, the RGB input signal is detected automatically. Use

AUTO normally.

If the RGB input signal range cannot be set appropriately

even when using AUTO, set according to the image. When

the setting is different, images will be displayed with washed 

out blacks and compressed gradients.
ADVANCED (AV input)
You can adjust more specifically. (See page 30.)
COLOR MODE
Changes the color mode on the screen. The color mode on 

the screen can also be changed using a remote control unit. 

(See page 21.)

*  sRGB is PC input only. See page 21 for details.

(In PIP mode, the main side setting is reflected in the image.)
WHITE BALANCE
THRU .............. Displays the input signal level as is. (for PC

DVI-D/PC HDMI only)

PRESET ......... Selects the color temperature using PRESET.

USER .............. Used for adjusting R-/G-/B-CONTRAST and

R-/G-/B-OFFSET respectively.

(In PIP mode, the main side setting is reflected in the image.)
PRESET
Selects the color temperature when the WHITE BALANCE is

set to PRESET.

The setting values are shown for reference. The color 

temperature of the screen varies over time.

This function is not intended to keep the color temperature 

constant.