Sony SA-VE522 / SA-VE525 / SA-WMS525 / SS-MS525 / SS-V521 Service Manual ▷ View online
1
SA-VE522/VE525/WMS525/
SS-MS525/V521
SERVICE MANUAL
ACTIVE SUBWOOFER
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Chinese Model
SPECIFICATION
Ver 1.1 2001.08
• SA-WMS525 and SS-MS525 is the micro
satellite system in SA-VE522/VE525.
• SS-V521 is SS-MS525 which can be pur-
chased alone.
SA-WMS525
SS-MS525
SS-V521
SS-V521
SS-MS525 (front, center, and rear speakers)
Speaker system
Full range x 2,
magnetically shielded
magnetically shielded
Speaker units
5 cm (2 in.), balance drive
type
type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
Maximum input power:
120
watts
Sensitivity level
87 dB (1 W, 1 m)
Frequency range
120 Hz - 20,000 Hz
Dimensions (w/h/d)
When attached speaker
grille:
Approx. 89 x 144 x 130
mm (3
grille:
Approx. 89 x 144 x 130
mm (3
5
/
8
x 5
3
/
4
x 5
1
/
8
in.)
When attached supplied
speaker stand:
Approx. 89 x 128 x 143
mm (3
When attached supplied
speaker stand:
Approx. 89 x 128 x 143
mm (3
5
/
8
x 5
1
/
8
x 5
3
/
4
in.) (pointed upwards)
Approx. 89 x 122 x 143
mm (3
Approx. 89 x 122 x 143
mm (3
5
/
8
x 4
7
/
8
x 5
3
/
4
in.) (pointed downwards)
Mass
When attached speaker
grille:
Approx. 750 g (1 lb 10 oz)
When attached supplied
speaker stand:
Approx. 850 g (1 lb 14 oz)
grille:
Approx. 750 g (1 lb 10 oz)
When attached supplied
speaker stand:
Approx. 850 g (1 lb 14 oz)
SA-WMS525 (subwoofer)
Speaker system
Active subwoofer,
magnetically shielded
magnetically shielded
Speaker unit
Woofer: 20 cm (8 in.),
cone type
cone type
Enclosure type
Advanced SAW type
Reproduction frequency range
26 Hz - 250 Hz
Amplifier section
Rated Power Output
Rated Power Output
120 W (8 ohms 20 Hz - 20
kHz, THD 0.8%)
kHz, THD 0.8%)
Inputs
LINE IN (input pin jack)
SPEAKER IN (input terminals)
SPEAKER IN (input terminals)
Outputs
LINE OUT (output pin jack)
SPEAKER OUT (output terminals)
SPEAKER OUT (output terminals)
General
Power requirements
USA and Canada: 120 V AC, 60 Hz
Europe, Australia and Chinese
E: 110-120V/220-240V AC, 50/60Hz
USA and Canada: 120 V AC, 60 Hz
Europe, Australia and Chinese
E: 110-120V/220-240V AC, 50/60Hz
220 - 230 V AC, 50/60 Hz
Power consumptions 90 W
1 W (standby mode)
Dimensions (w/h/d) Approx. 230 x 392 x
464 mm (9
1
/
8
x 15
1
/
2
x
18
3
/
8
in.), including front
grille
Mass Approx. 13.2 kg
(29 lb 2 oz)
Supplied accessories
SA-VE525
Foot pads (16)
Center speaker stand (1)
Screw (for the center speaker stand) (1)
Washer (for the center speaker stand) (1)
Audio connecting cord (1)
Speaker connecting cords, 10 m (32 ft 9
Foot pads (16)
Center speaker stand (1)
Screw (for the center speaker stand) (1)
Washer (for the center speaker stand) (1)
Audio connecting cord (1)
Speaker connecting cords, 10 m (32 ft 9
3
/
4
in.) (2)
Speaker connecting cords, 3.5 m (11 ft 6 in.) (3)
Speaker connecting cords, 2.5 m (8 ft 2
Speaker connecting cords, 2.5 m (8 ft 2
1
/
2
in.) (2)
SA-VE522
Foot
Foot
SS-V521
Foot pads (4)
Speaker connecting cords, 10m (32 ft 9 in.) (1)
Foot pads (4)
Speaker connecting cords, 10m (32 ft 9 in.) (1)
pads (8)
Audio connecting cord (1)
Speaker connecting cords, 3.5 m (11 ft 6 in.) (2)
Speaker connecting cords, 2.5 m (8 ft 2
Speaker connecting cords, 3.5 m (11 ft 6 in.) (2)
Speaker connecting cords, 2.5 m (8 ft 2
1
/
2
3
/
4
in.) (2)
Design
and specifications are subject to change without
notice.
9-
873
-
807
-1
2
2001
H
0200-1
© 2001.
8
Sony Corporation
Home
Audio Company
Shinagawa Tec Service Manual Production Group
2
SA-VE522/VE525/WM525/SS-MS525/V521
TABLE OF CONTENTS
1. GENERAL
.......................................................................... 3
2. DIAGRAMS
2-1. Circuit Boards Location ........................................................ 3
2-2. Schematic Diagram ............................................................... 4
2-3. Printed Wiring Board ............................................................ 5
2-2. Schematic Diagram ............................................................... 4
2-3. Printed Wiring Board ............................................................ 5
3. EXPLODED VIEW
3-1. Front Panel Section ............................................................... 6
3-2. Rear Panel Section ................................................................ 6
3-3. SS-V521 Section, SS-MS525 Section .................................. 7
3-2. Rear Panel Section ................................................................ 6
3-3. SS-V521 Section, SS-MS525 Section .................................. 7
4. ELECTRICAL PARTS LIST
......................................... 8
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
(US model)
Fig. A. Using an AC voltmeter to check AC leakage.
0.15
µ
F
To Exposed Metal
Parts on Set
Parts on Set
1.5k
Ω
AC
voltmeter
(0.75V)
voltmeter
(0.75V)
Earth Ground
3
3
SA-VE522/VE525/WM525/SS-MS525/V521
SECTION 1
GENERAL
• Location of controls
– Front view (a part) –
SECTION 2
DIAGRAMS
1 POWER button
2 ON/STANDBY indicator
3 LEVEL dial
4 MODE dial
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
C
: panel designation.
For printed wiring boards.
Note:
• X
: parts extracted from the component side.
• Y
: parts extracted from the conductor side.
• b
: Pattern from the side which enables seeing.
•
: B+ Line.
•
: B– Line.
• Voltages are dc with respect to ground under no-signal con-
ditions.
no mark : Power on
no mark : Power on
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10M
Ω
).
Voltage variations may be noted due to normal preduction
tolerances.
tolerances.
• Signal path.
K
: AUDIO
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
2-1. Circuit Boards Location
Note:
The components identi-
fied by mark
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
• Abbreviation
CND : Canadian model
SP
CND : Canadian model
SP
: Singapore model
MX
: Mexican model
AUTO POWER board
MAIN board
POWER board
LED board
POWER SWITCH board
CONTROLboard
1
2
3
4
SA-VE522/VE525/WM525/SS-MS525/V521
2-3. SCHEMATIC DIAGRAM
4
4
BA4558
BA4558
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22
BA4558
BA4558
39k
BA4558
BA4558
BA4558
BA4558
W
W
HPF
MIX AMP
BA4558
BA4558
680
680
2SA1464-T2Y13
POEWR AMP
16V
11ES-NTA2B
11ES-NTA2B
11ES-NTA2B
11ES-NTA2B
MZS15-2L
MZS15-2L
2SA733-K
2SC2785
680
1W
D801
ON/STANDBY
– 0.9
13.6
– 0.3
– 13.9
13.3
12.9
– 13.9
AEP,UK,CH T1AL/250V
C4
JW605
SP
Ver 1.
1
2001. 0
8