Sharp UP-3515 (serv.man11) Driver / Update ▷ View online
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.63
Doc: up35xx_pm_e_1v67
Page 21 / 41
Parts & Technical Services
>>> Changes / Improvements / Corrections since V1.63 <<<
C 3
Saved Reports in Inline-System
C 3.1
In case of an Inline System with a Backup-Master, while the Backup-Master has taken over the role
of the Master (due to Master down), the Backup-Master still behaves like the Satellite as far as the
Saved Reports are concerned.
Only the Electronic Journal as well as PGM Backup and ALL RAM Backup, according to their setting,
will be saved on SD Card.
This specification is valid from version V1.63 onwards.
of the Master (due to Master down), the Backup-Master still behaves like the Satellite as far as the
Saved Reports are concerned.
Only the Electronic Journal as well as PGM Backup and ALL RAM Backup, according to their setting,
will be saved on SD Card.
This specification is valid from version V1.63 onwards.
Stacked Reports
C 3.2
A Stacked Report called at the Satellite shows a “strange” behaviour like no cut between the
individual reports or even not printed correctly at all.
This is corrected with V1.63.
individual reports or even not printed correctly at all.
This is corrected with V1.63.
Individual Clerk-Z Report is missing in the Electronic Journal
C 3.3
This phenomenon only occurs by using the Recall Closed Transaction feature and only after the
following entry:
following entry:
•
Make a GLU registration and finalize it.
•
Carry out the individual Clerk-Z Report.
•
Return to registration mode, recall the previous finalized GLU registration and finalize it
again.
again.
Now, if the General-Z Report has been taken, the individual Clerk-Z Report is missing in the
electronic Journal, but not on the paper journal.
Since V1.63 the individual Clerk-Z Report will also be written into the Electronic Journal even after
above mentioned operation.
electronic Journal, but not on the paper journal.
Since V1.63 the individual Clerk-Z Report will also be written into the Electronic Journal even after
above mentioned operation.
Missing discount in PLU report by granting SBTL% or SBTL(-) discount
C 3.4
Although a SBTL% or SBTL(-) discount has been given, it was not reported in the PLU report.
Since V1.63 the given discount will be reported in the PLU report as well.
Since V1.63 the given discount will be reported in the PLU report as well.
No saving of EJ if General-Z report is in Stacked Report
C 3.5
If the General-Z report has been put to a Stacked Report and the SRV parameter #992B is set to
“Save&Clear EJ on SD Card after Gen. Z” (+1) the EJ was not written and cleared to the SD card
after the Stacked Report was carried out.
This has been corrected with V1.63.
“Save&Clear EJ on SD Card after Gen. Z” (+1) the EJ was not written and cleared to the SD card
after the Stacked Report was carried out.
This has been corrected with V1.63.
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.64
Doc: up35xx_pm_e_1v67
Page 22 / 41
Parts & Technical Services
>>> Changes / Improvements / Corrections since V1.64 <<<
C 4
System hang up after update with ROM Version V1.62 / V1.63
C 4.1
In a very few cases it can happen that after update of a machine with a Fiscal ROM like V1.62 or
V1.63 by using the SD Card function, the screen remains black after the Master-Reset.
Sometimes a break error can be seen in the display. In this condition the machine hangs and a reset
of the machine is not possible anymore. No further update is possible.
By updating the machine with ROM Version V1.64 this phenomenon will not occur.
V1.63 by using the SD Card function, the screen remains black after the Master-Reset.
Sometimes a break error can be seen in the display. In this condition the machine hangs and a reset
of the machine is not possible anymore. No further update is possible.
By updating the machine with ROM Version V1.64 this phenomenon will not occur.
Recall Transaction finalized by another Clerk and using Supervisor function
C 4.2
It could happen that after recall of a transaction, which has been finalized by another Clerk, the
Clerk totalizers were not updated correctly. In order to get correctly updated Clerk totalizers the
following specifications becomes valid with V1.64:
Clerk totalizers were not updated correctly. In order to get correctly updated Clerk totalizers the
following specifications becomes valid with V1.64:
•
A transaction can be recalled only from that clerk who has finalized it.
•
A Supervisor Clerk will be reassigned to that clerk who has finalized the transaction before,
before he is able to reopen the transaction. This also is valid if the Supervisor Clerk works on
his own account.
before he is able to reopen the transaction. This also is valid if the Supervisor Clerk works on
his own account.
Faulty distribution of SRV parameters in an Inline-System
C 4.3
Under some circumstances changes at a SRV Job Code containing fiscal as well as non-fiscal
parameters were not distributed correctly by using the SRV MODE Job:
parameters were not distributed correctly by using the SRV MODE Job:
SRV MODE\ 4 DOWN LOAD\1 SRV PARAMETER
This is corrected with V1.64.
Registration with more than one granted GroupDiscount
C 4.4
If several Group Discounts have been granted during a registration, a miscalculation could happen
if more than one of them were voided.
In order to avoid any miscalculation, only the last granted Group Discount can be voided. If more
than one Group Discount must be voided the complete registration has to be voided by using
Subtotal Void.
This is change is valid since V1.64.
if more than one of them were voided.
In order to avoid any miscalculation, only the last granted Group Discount can be voided. If more
than one Group Discount must be voided the complete registration has to be voided by using
Subtotal Void.
This is change is valid since V1.64.
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.65
Doc: up35xx_pm_e_1v67
Page 23 / 41
Parts & Technical Services
>>> Changes / Improvements / Corrections since V1.65 <<<
C 5
Electronic Journal entry after Saved Report
C 5.1
It is fiscal specification, that whenever the Electronic Journal has been deleted, the new Electronic
Journal starts with the ECR system information as the very first entry. Unfortunately this ECR system
information entry was missing after the “Saved Report” has been carried out at the Satellite.
This has been corrected by ROM version V1.65.
Journal starts with the ECR system information as the very first entry. Unfortunately this ECR system
information entry was missing after the “Saved Report” has been carried out at the Satellite.
This has been corrected by ROM version V1.65.
Void of Group Discount
C 5.2
In case of multiple voids of former given GroupDiscounts a miscalculation of the total amount for
the transaction can happen.
With V1.65, only the last given GroupDiscount can be voided.
the transaction can happen.
With V1.65, only the last given GroupDiscount can be voided.
Miscalculation by voiding a promotion in combination with overlapped Clerk
C 5.3
System configuration: StandAlone or Inline System with enabled overlapped Clerk feature. At least
one promotion table is defined.
Example: Make a registration of PLUs until the promotion becomes valid. Now, void all items by
using direct or even indirect void but do not finalise this transaction. Another Clerk signs on, makes
his registration and finalizes it. If the former Clerk sign on again a wrongly calculated subtotal is
shown.
Since V1.65 the subtotal amount will be calculated correctly.
one promotion table is defined.
Example: Make a registration of PLUs until the promotion becomes valid. Now, void all items by
using direct or even indirect void but do not finalise this transaction. Another Clerk signs on, makes
his registration and finalizes it. If the former Clerk sign on again a wrongly calculated subtotal is
shown.
Since V1.65 the subtotal amount will be calculated correctly.
Wrong folder name for Saved Report sales data
C 5.4
During the Saved Report function the sales data will be saved into a folder where the date for that
sales data is part of the folder name. In case that the sales data has to be stored for the previous
day according to “DAY START TIME” a date miscalculation will occur if the current date is the 1
sales data is part of the folder name. In case that the sales data has to be stored for the previous
day according to “DAY START TIME” a date miscalculation will occur if the current date is the 1
st
of
March. In this case the calculated previous day is the 29
th
of February even this date does not exist.
This problem has been solved with V1.65
Training totalizer in the General report
C 5.5
If the machine has been setup in a non-fiscal mode, a Training totalizer is printed on the General
report. This print out is against the specification.
Since V1.65 this totalizer will not be printed anymore.
report. This print out is against the specification.
Since V1.65 this totalizer will not be printed anymore.
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.65
Doc: up35xx_pm_e_1v67
Page 24 / 41
Parts & Technical Services
Intermediate GLU at the Orderman
C 5.6
It is possible to call an intermediate GLU at the Orderman using the “Subtot” function.
Unfortunately, the BILL print header has been used for that print out.
With V1.65 the correct print header, the intermediate GLU print header, is used instead.
Unfortunately, the BILL print header has been used for that print out.
With V1.65 the correct print header, the intermediate GLU print header, is used instead.
Split of a Condiment PLU at the Orderman
C 5.7
A split of a Condiment PLU results in a wrong registration result at the ECR.
Due to the system specification a split of a Condiment PLU by number input is inhibited. This is
valid for the Orderman also.
With V1.65 a split of a Condiment PLU at the Orderman will show an “ENTRY ERROR” at the
Orderman because it has been rejected from the ECR.
Due to the system specification a split of a Condiment PLU by number input is inhibited. This is
valid for the Orderman also.
With V1.65 a split of a Condiment PLU at the Orderman will show an “ENTRY ERROR” at the
Orderman because it has been rejected from the ECR.
Click on the first or last page to see other UP-3515 (serv.man11) service manuals if exist.