Sharp XE-A303 (serv.man3) Service Manual ▷ View online
XE-A303 (V)
OP X/Z, X1/Z1, X2/Z2 MODE
3 – 2
• Stop of printing reports (Report cancel function):
This ECR has the function of report stopping for PLU report.
*
1 To read respective reports, it is necessary to follow the procedure
below.
*
2 PLU code range can be specified by entering the start and end
numbers according to the following procedure.
When specifying a single PLU code, the start number has only to be
When specifying a single PLU code, the start number has only to be
entered.
*
3 The clerk code does not need to enter at the OPX/Z mode.
In OPX/Z mode, it is issued the report of the assigned clerk.
*
4 Reading display only.
The displayed amount can be cleared by [CL] key..
*5
Hourly range can be specified by entering the start and end hour
according to the following procedure.
according to the following procedure.
When specifying a single hour, the start hour has only to be entered.
*
6 To read respective contents, it is necessary to follow the procedure
below.
[Action]
Individual counters for the following Z reports are incremented when
those reports are printed.
those reports are printed.
1) General daily total report (Z1)
2) General periodic total report (Z2)
[Additional function]
(1) Overflow mark
If the amount or quantity in any totalizer other than GT to be printed
on X or Z reports exceeds a programmed limit, the indication mark
(overflow mark) is printed for the totalizer concerned.
(overflow mark) is printed for the totalizer concerned.
The overflow mark may be printed even if a totalizer does not reach
the maximum amount. This occurs, for example, when the amount
or quantity in the totalizer gets smaller than the maximum amount
due to the entry of a negative amount after the overflowing of the
due to the entry of a negative amount after the overflowing of the
totalizer. This means that when the totalizer overflows once, the
overflow mark (for example,"!!") is printed.
(2) MODE TITLE
Each report prints a MODE TITLE at a header of report.
The Report Titles are as follows.
(3) Report cancel function
It can be cancelled by turned the mode switch to MGR position
while the data is printed. (In this case, the contents of memory are
while the data is printed. (In this case, the contents of memory are
not cleared.)
<Print sample of Report cancel>
MODE:
X : Daily operater X report
Z : Daily operater Z report
X1 : Daily X report
Z1 : Daily Z report
X2 : Periodic X report
Z2 : Periodic Z report
(X report): The corresponding data is held in the ECR.
(Z report): The corresponding data is cleared in the ECR.
(X report)
Reading
Resetting
(Z report)
(Z report)
KEY
Start NO.
XXXX
XXXX
End NO.
All
PLU
Resetting
Reading
CL
KEY
(Display amount)
(Display initialize)
@/FOR
XX
Start
XX
End
#/TM/ST
Resetting
Reading
ALL
Reading
Executing
EURO STATUS
TL
JOB#
OPX report
*
OPX
*
OPZ report
*
OPZ
*
X1 report
*
X 1
*
Z1 report
*
Z 1
*
X2 report
*
X 2
*
Z2 report
*
Z 2
*
:
:
:
* * * * * * * *
1
the report cancel symbol
123456789012345678901234567890
XE-A303 (V)
OP X/Z, X1/Z1, X2/Z2 MODE
3 – 3
CHANGING EURO FUNCTION (Z2 MODE JOB)
This job is own to be able to be changed easily from local currency sys-
tem to EURO currency system in X2/Z2 mode.
(Reading the current EURO status)
(Changing EURO Function)
About EURO STATUS are shown the following pages.
It is executing automatically to change from status (A) to status (B), (C), (D).
Selectable type is one of below 4 types.
And the selectable type is decided as below for each status.
And the selectable type is decided as below for each status.
Marked “
u
” is selectable
[Action]
It is executed some of below JOBs which is needed for each status.
1) Issue General Z1 report.
2) Issue General Z2 report.
3) Clear GT1/2/3 and Training GT.
4) Convert the unit price of DEPT/PLU from LOCAL currency to EURO.
If new unit price is over the max digits, its price is set as “0.00”.
5) Convert the HALO amount and HALO digits from LOCAL currency
to EURO.
If new HALO amount is over the max digits, its price is set as “0.00”.
If new HALO amount is over the max digits, its price is set as “0.00”.
6) Change PGM function “EX1 AMOUNT PRINTING FOR TOTAL
AND CHANGE YES/NO”.
7) Change PGM function “EX1 CALCULATTION METHOD DIVISION/
MULTIPLICATION”.
8) Set “Domestic currency symbol” as EURO SYMBOL.
9) Set “Domestic TAB” as “2”.
10) Set “EX1 currency symbol” as the suitable data.
11) Set “EX1 TAB” as the suitable data.
12) Set “Rounding SYSTEM (Denmark/Sweden/Normal)” as “Normal”.
13) Set “Rounding up/down of the unit digits of AMOUNT" as “No”.
14) Set “Lowest digit entering limitation of item” as “Arbitrary”.
15) Set “Lowest digit entering limitation of payment” as “Arbitrary”.
16) Set “Difference memory” as “No”.
17) Set “Rounding of foreign currency for EX” as “Round off (4-DOWN,
5-UP)”. (EURO Regulation)
Notes:
a) This JOB cannot set below additional EURO function auto-
matically.
Below items must be set by each PGM JOB after this job.
Below items must be set by each PGM JOB after this job.
(1) EX1 RATE
(2) “CHECK, CREDIT operation for EX1 Yes/No”
b) When the unit price is converted, the rounding method of EURO
currency is fixed as “Round off (4-DOWN, 5-UP)”.
[EURO Regulation]
[EURO Regulation]
[Selecting type and its action]
Current status (A) :
Y : 1
= EURO STATUS (B)
2
= EURO STATUS (C)
3
= EURO STATUS (D)
CURRENT STATUS
4
Selectable STATUS
(A)
(B)
(C)
(D)
(A)
------
u
u
u
(B)
------
------
u
u
(C)
------
------
------
u
(D)
------
------
------
------
TL
(X2/Z2 mode) 800
Y
TL
(X2/Z2 mode) 800
CURRENT STATUS (A)
Selected STATUS
(B)
(C)
(D)
1) General Z1 report
ISSUE
ISSUE
ISSUE
2) General Z2 report
ISSUE
ISSUE
ISSUE
3) GT1/2/3
------
CLEAR
CLAER
4) Convert the unit price of DEPT/PLU
------
CONVERTING
CONVERTING
5) Convert the HALO amount and HALO digits
------
CONVERTING
CONVERTING
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
“YES”
“YES”
“NO”
7) EX1 CALCULATTION METHOD
“DIVISION”
“MULTI.”
“MULTI.”
8) Domestic currency symbol
------
[EURO]
[EURO]
9) Domestic TAB
------
“2”
“2”
10) EX1 currency symbol
[EURO]
The Current "Domestic
currency symbol"
------
11) EX1 TAB
"2"
The Current “Domestic TAB”
------
12) Rounding SYSTEM (Denmark/Sweden/Normal)
------
“Normal”
“Normal”
13) Rounding up/down of the unit digits of AMOUNT
------
“No”
“No”
14) Lowest digit entering limitation of item
------
“Arbitrary”
“Arbitrary”
15) Lowest digit entering limitation of payment
------
“Arbitrary”
“Arbitrary”
16) Difference memory
------
“No”
“No”
17) Rounding of foreign currency for EX
“ROUND OFF (4DOWN-5UP)” “ROUND OFF (4DOWN-5UP)” “ROUND OFF (4DOWN-5UP)”
Marked “------” is remaining the current data.
XE-A303 (V)
OP X/Z, X1/Z1, X2/Z2 MODE
3 – 4
Current status (B):
Current status (C):
CURRENT STATUS (B)
Selected STATUS
(C)
(D)
1) General Z1 report
ISSUE
ISSUE
2) General Z2 report
ISSUE
ISSUE
3) GT1/2/3
CLEAR
CLAER
4) Convert the unit price of DEPT/PLU
CONVERTING
CONVERTING
5) Convert the HALO amount and HALO digits
CONVERTING
CONVERTING
6)
EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
“YES”
“YES”
7) EX1 CALCULATTION METHOD
“MULTI.”
“MULTI.”
8) Domestic currency symbol
[EURO]
[EURO]
9) Domestic TAB
“2”
“2”
10) EX1 currency symbol
The Current "Domestic
currency symbol"
[SPACE]
11) EX1 TAB
The Current "Domestic TAB"
------
12) Rounding SYSTEM (Denmark/Sweden/Normal)
“Normal”
"Normal"
13) Rounding up/down of the unit digits of AMOUNT
“No”
"No"
14) Lowest digit entering limitation of item
“Arbitrary”
“Arbitrary”
15) Lowest digit entering limitation of payment
“Arbitrary”
“Arbitrary”
16) Difference memory
“No”
“No”
17) Rounding of foreign currency for EX
“ROUND OFF (4DOWN-5UP)”
“ROUND OFF (4DOWN-5UP)”
Marked “------” is remaining the current data.
CURRENT STATUS (C)
Selected STATUS
(D)
1) General Z1 report
ISSUE
2) General Z2 report
ISSUE
3) GT1/2/3, Training GT
------
4) Convert the unit price of DEPT/PLU
------
5) Convert the HALO amount and HALO digits
------
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
“NO”
7) EX1 CALCULATTION METHOD
“MULTI.”
8) Domestic currency symbol
[EURO]
9) Domestic TAB
“2”
10) EX1 currency symbol
[SPACE]
11) EX1 TAB
------
12) Rounding SYSTEM (Denmark/Sweden/Normal)
------
13) Rounding up/down of the unit digits of AMOUNT
------
14) Lowest digit entering limitation of item
------
15) Lowest digit entering limitation of payment
------
16) Difference memory
------
17) Rounding of foreign currency for EX
“ROUND OFF (4DOWN-5UP)”
Marked “------” is remaining the current data.
SHARP CORPORATION
Information and Communication Systems Group
Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
Yamatokoriyama, Nara 639-1186, Japan
2006 August Printed in Japan
t
2006 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
