DOWNLOAD Sharp XE-A303 (serv.man3) Service Manual ↓ Size: 674.59 KB | Pages: 28 in PDF or view online for FREE

CODE : 00Z

CONTENTS

Parts marked with "

!

" are important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

XEA303VPME

■

 LEAD-FREE SOLDER

CHAPTER 1. MASTER RESET AND PROGRAM RESET  . . . . . . 1 - 1

CHAPTER 2. PROGRAM MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE. . . . . . . . . . . . . . . . . . 3 - 1

XE-A303 (V)   LEAD-FREE SOLDER

■

The PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. 

The alphabet following the LF mark shows the kind of lead-free solder. 

When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident. 

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is rec-

ommendable. 

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to

conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed the heat-resistive tem-
perature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed. 

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.  

If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com-
pletion of soldering work. 

If the soldering iron tip is discolored black during soldering work, clean
and file the tip with steel wool or a fine filer. 

5mm

Lead-Free

Solder composition 
code (Refer to the 
table at the right.)

Solder composition

Sn-Ag-Cu

Sn-Ag-Bi
Sn-Ag-Bi-Cu

Sn-Zn-Bi

Sn-In-Ag-Bi

Sn-Cu-Ni

Sn-Ag-Sb

Bi-Sn-Ag-P
Bi-Sn-Ag

a

b

z

i

n

s

p

Solder composition code

a

XE-A303 (V)

MASTER RESET AND PROGRAM RESET

1 – 1

Master resetting clears the entire memory and resumes initial values.

Master resetting can be accomplished by using the following procedure:

Procedure:

1) Unplug the AC cord from the wall outlet, or set the mode switch to OFF position.

2) Set the mode switch to the PGM position.

3) While holding down both the JOURNAL FEED key and [CL] key, plugin the AC cord to the wall outlet.

The master reset can also be accomplished in the following case.

In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the power

has been plugined the AC cord to the wall outlet.

(This is because if power failure occurs with no battery attached to the machine, all the memories are lost and the machine does not work properly

after power recovery; this requires the master reset operation.)

This resetting resumes the initial program without clearing memory.

This resetting can be operated at below sequence in PGM mode.

Procedure:

1) Unplug the AC cord from the wall outlet.

2) Wait over 1 minute for discharging.

3) Set the mode switch to the PGM position.

4) While holding down the JOURNAL FEED key and RECEIPT FEED key, plugin the AC cord to the wall outlet.

Note: In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the

power has been restored.

XE-A303 (V)

PROGRAM MODE

2 – 1

The machine allows you to read every program stored in the PGM mode.

■

(

*

) PLU code range can be specified by entering the start and end numbers according to the following procedure.

When specifying a single time interval, PLU code, the start number has only to be entered.

■

*

*

Report name

Key sequence

Programmed data1 report

Programmed data2 report

2 

3 

Auto key programming report

1 

3 

Printer density report

3 

3 

DEPT data report

4 

3 

PLU data report (

*

)

TL

TL

TL

TL

TL

Start No.           

End No.

PLU

HEADER

DATE/TIME/CLERK CODE
MACHINE NO. /CC-NO. /CLERK NAME

FUNCTION NO. /TEXT/PROGRAM (

*

1)

AMOUNT WITH SIGN
FUNCTION NO. /TEXT/PROGRAM (

*

1)

HALO WITHOUT SIGN/RATE WITH SIGN

FUNCTION NO. /TEXT

FUNCTION NO. /TEXT/HALO

FUNCTION NO. /TEXT/PROGRAM (

*

2)

FUNCTION NO. /TEXT/PROGRAM (

*

3)

CURRENCY SYMBOL/RATE

008
008
008
008
008
002

999.999999

05/02/2001 12:34PM
123456#123456

F

01 (-) xxxxxx

F

02 %1xxxxxxxx

L100.00%

F

03 %2xxxxxxxx

L100.00%

F

04 NET1xxxx

F

05 DIFFERxxxxxx

 

 :

  

 :

F

26 

***

RAxxxxxxx

F

27 

***

POxxxxxxx

 

 :

F

32 CASHxxxx

F

33 CHECKxxxxxxx

F

34 CHECK2xxxxxx

F

35 CREDI T1xxxxx

F

36 CREDI T2xxxxx

F

37 EXCH1xxxxxxx

  ABCD

F

38 EXCH2xxxxxxx

 

 :

01

M.CLERK_____

007

-1000.00

000

-10.00%

000

-100.00%

9
9

 

 :

F

85              #

F

86 COPY

F

87 EX1 CHG

F

88 AMOUNT

#5
#6
#7
#8
#10
#11
#12
#13
#14
#20
#21
#22
#35 

T

1

T

2

T

3 

T

4

 

C#01 ____________
C#02 xxxxxxxxxxxx
 

:

C#25 xxxxxxxxxxxx

00000000
00000000
00000000

0000
0000

0

00

00/00/0000

00:00

9999999.99

999999.99
999999.99

007 

10.0000%

123.45

4.0000%

0.10

-5.0000%

0.20

------

11
12

00

:

LOGO TEXT
(It is according with LOGO FORMAT.)

FUNCTION NO. /TEXT

TAX1 RATE
LOWER TAX LIMIT
TAX2 RATE
LOWER TAX LIMIT
TAX3

TAX4 ( g------ h:INHIBIT)
Clerk No./Clerk name/CODE

(JOB#5)   FUNCTION SELECT 
(JOB#6)   PRINT FUNCTION
(JOB#7)   RECEIPT PRINT FORMAT
(JOB#8)   EURO FUNCTIONS
(JOB#10) POWER SAVING PROGRAMMING 
(JOB#11) LOGO FORMAT
(JOB#12) EURO PROGRAMMING
(JOB#13) EURO CHANGING DATE (Printed by 

Date format)

(JOB#14) EURO CHANGING HOUR
(JOB#20) SENTINEL AMOUNT
(JOB#21) CHECK CASHING LIMITATION AMOUNT
(JOB#22) CHECK CHANGE LIMITATION AMOUNT
(JOB#35) USB Timeout time

VARIOUS PROGRAM 

Refer to the programming section about the 
data of each JOB.

FUNCTION NO. /TEXT

A: ENTRY FOR ITEM 

A

ENABLE

0

DISABLE

1

B: ENTRY FOR SBTL

B

ENABLE

0

DISABLE

1

C: LIMITATION DIGITS (for (-) key) = 0 to 7 (0 FIXED for [%n])

A: Footer print on Receipt

A

No

0

Yes

1

B: Entry of amount tenderd

B

Noncompulsory (Cash, check)/Inhibit (Credit)

0

Compulsory

1

C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8