Sharp XE-A212 (serv.man5) User Manual / Operation Manual ▷ View online
75
Removing the paper roll
When a red dye appears on the paper roll, it is time to replace it. Replace the paper roll with a new one. If you
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
When not using the take-up spool (using as receipt paper):
1.
Remove the printer cover.
2.
Lift up the print roller release lever to unlock and open the print
roller arm.
roller arm.
3.
Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
When using the take-up spool (using as journal paper):
1.
Turn the mode switch to a position other than “
” with the
power cord connected.
2.
Remove the printer cover.
3.
Press the
F
key to advance the journal paper until its printed
part is out of the way.
4.
Cut the paper and remove the take-up spool.
5.
Lift up the print roller release lever to unlock and open the print
roller arm.
roller arm.
6.
Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
7.
Remove the outer side of the take-up spool as shown
on the left.
on the left.
8.
Remove the printed journal roll from the take-up spool.
Area to cut
Print roller
release lever
release lever
Print roller arm
A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 75
76
Installing the paper roll
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
Installing the receipt paper roll:
1.
Turn the mode switch to a position other than
“
“
” with the power cord connected.
2.
Remove the printer cover.
3.
Lift up the print roller release lever to unlock
and open the print roller arm.
and open the print roller arm.
4.
Set the paper correctly in the paper roll cradle.
5.
Feed the end of the paper along with the paper
positioning guides.
positioning guides.
6.
While holding down the paper, slowly close the print roller arm,
and push down the arm until you hear a click locking the arm.
Make sure securely you push down the center of the wing part of
the arm as per the diagram. The paper will be fed automatically.
and push down the arm until you hear a click locking the arm.
Make sure securely you push down the center of the wing part of
the arm as per the diagram. The paper will be fed automatically.
If the print roller arm is not securely locked, printing is
not done right. If this problem occurs, open the arm, and
close the arm as instructed above.
not done right. If this problem occurs, open the arm, and
close the arm as instructed above.
7.
Cut off the excess paper using the edge of the inner cover, and
replace the printer cover. Press the
replace the printer cover. Press the
F
key to make sure the
paper end comes out of the printer cover and clean paper appears.
If the paper end does not come out, open the printer
cover, and pass the paper end between the paper cutter
and the paper guide of the printer cover, and replace the
cover.
cover, and pass the paper end between the paper cutter
and the paper guide of the printer cover, and replace the
cover.
Installing the journal paper roll:
1.
Turn the mode switch to a position other than “
” with the power
cord connected.
2.
Remove the printer cover.
3.
Lift up the print roller release lever to unlock and open the print
roller arm.
roller arm.
4.
Set the paper correctly in the paper roll cradle.
5.
Feed the end of the paper along with the paper positioning guides.
6.
While holding down the paper, slowly close the print roller arm,
and push down the arm until you hear a click locking the arm.
Make sure securely you push down the center of the wing part of
the arm as per the diagram. The paper will be fed automatically.
and push down the arm until you hear a click locking the arm.
Make sure securely you push down the center of the wing part of
the arm as per the diagram. The paper will be fed automatically.
If the print roller arm is not securely locked, printing is
not done right. If this problem occurs, open the arm, and
close the arm as instructed above.
not done right. If this problem occurs, open the arm, and
close the arm as instructed above.
Paper positioning guides
A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 76
77
7.
Insert the end of the paper into the slit in the spool. (Press the
F
key to feed more paper if required.)
8.
Wind the paper two or three turns around the spool shaft.
9.
Set the spool on the bearing, and press the
F
key to take up
excess slack in the paper.
10.
Replace the printer cover.
You can wind the roll paper in OP X/Z, X1/Z1, and X2/Z2
modes even if you programmed so that the printer is
used for issuance of receipts. This may be convenient to
wind reports. In this case, set the roll paper to the take-
up spool.
modes even if you programmed so that the printer is
used for issuance of receipts. This may be convenient to
wind reports. In this case, set the roll paper to the take-
up spool.
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. Never touch
the print head immediately after printing, as the head may still be hot.
1.
Remove the printer cover.
2.
Lift up the print roller release lever to unlock and open the print roller arm.
3.
Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.
4.
Reset the paper roll correctly by following the steps in “Installing the paper roll”.
When the printed text is getting dark or faint, paper dust may be stuck to the print head, sensor and/or roller.
Clean them as follows:
Clean them as follows:
Caution:
• Never touch the print head with a tool or anything hard as it may damage the head.
• The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
• Never touch the print head with a tool or anything hard as it may damage the head.
• The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
1.
Turn the mode switch to the “
” position.
2.
Remove the printer cover.
3.
Lift up the print roller release lever to unlock and open the
print roller arm.
print roller arm.
4.
Remove the paper roll referring to the “Removing the
paper roll” section.
paper roll” section.
5.
Clean the print head with a cotton swab or soft rag
moistened with ethyl alcohol or isopropyl alcohol. Clean
the roller and the sensor in the same manner.
moistened with ethyl alcohol or isopropyl alcohol. Clean
the roller and the sensor in the same manner.
6.
Reset the paper roll correctly by following the steps in
“Installing the paper roll”.
“Installing the paper roll”.
Cleaning the Printer (Print Head / Sensor / Roller)
7
Removing a Paper Jam
6
Print head
Roller
Sensor
A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 77
78
The till in the register is detachable. After closing your business for the day, remove the till from the drawer and
keep the drawer open. The 8-denomination coin case is also detachable from the till. To detach the drawer, pull
it forward fully with the till removed, and remove it by lifting it up.
keep the drawer open. The 8-denomination coin case is also detachable from the till. To detach the drawer, pull
it forward fully with the till removed, and remove it by lifting it up.
The drawer automatically opens. However, when a power failure occurs or the
machine becomes out of order, slide the lever located on the bottom of the
machine in the direction of the arrow. (See the diagram at the left.)
machine becomes out of order, slide the lever located on the bottom of the
machine in the direction of the arrow. (See the diagram at the left.)
The drawer will not open if it is locked with the key.
Lever
Opening the Drawer by Hand
9
2
1
Drawer
Till
Coin case
8-denomination coin case
(detatchable)
Bill case
Removing the Till and the Drawer
8
A212_5 OPERATOR MAINTENANCE 03.7.5 7:53 AM Page 78
Click on the first or last page to see other XE-A212 (serv.man5) service manuals if exist.