Sharp XE-A201 (serv.man8) User Manual / Operation Manual ▷ View online
63
This cash register displays a low battery symbol (
) when the batteries are low, and displays a no battery
symbol (
) when batteries are extremely low or batteries are not installed.
When the low battery symbol is displayed, replace the batteries with new ones as soon as possible. The
existing batteries will be dead in about two days.
When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC power cord is
disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any
data stored in memory will be cleared.
existing batteries will be dead in about two days.
When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC power cord is
disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any
data stored in memory will be cleared.
Be sure to observe precautions shown on page 1 when handling batteries.
To replace the batteries:
1.
Make sure that the cash register is plugged in.
2.
Turn the mode switch to the REG position with the power cord connected.
3.
Remove the printer cover.
4.
Open the battery compartment cover and remove the old batteries.
5.
Install three new R6 or LR6 batteries (“AA” size) in the battery compartment.
Be sure the positive and negative poles of each battery are facing in the
proper direction. When they are installed correctly, the “
Be sure the positive and negative poles of each battery are facing in the
proper direction. When they are installed correctly, the “
” or “
” symbol
will disappear.
6.
Close the battery compartment cover.
7.
Replace the printer cover.
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls other than those specified could cause paper jamming, resulting in register
malfunction.
The use of any other paper rolls other than those specified could cause paper jamming, resulting in register
malfunction.
Paper specification
Paper width: 57.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality: Thermal paper
• Be sure to set paper roll(s) prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful to set the roll and cut the paper end correctly.
If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development ability in the
pasted or taped area due to the deterioration of the heat-sensitive color development component of the paper
surface. This may result in nothing appearing at this location when printing. Therefore, when setting a new paper
roll in the machine, be sure to cut off approximately one revolution (approx. 25 cm long).
If the top end of the paper roll is fixed with paste or tape, the paper may lose its color development ability in the
pasted or taped area due to the deterioration of the heat-sensitive color development component of the paper
surface. This may result in nothing appearing at this location when printing. Therefore, when setting a new paper
roll in the machine, be sure to cut off approximately one revolution (approx. 25 cm long).
(How to set the paper roll)
(How to cut the paper end)
Correct
Incorrect
To the printer
Incorrect
To the printer
Correct
Replacing the Paper Roll
5
Replacing the Batteries
4
A201_5 OPERATOR MAINTENANCE 01.11.11 10:24 AM Page 63
64
Removing the paper roll
When a red dye appears on the paper roll, it is time to replace it. Replace the paper roll with new one. If you
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself.
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself.
When the take-up spool is not used:
1.
Turn the mode switch to the REG position with the power cord connected.
2.
Remove the printer cover.
3.
Cut the paper behind the printer and near the paper roll.
4.
Press the
F
key until the paper remaining in the printer comes out
completely.
5.
Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
When the take-up spool is used:
1.
Turn the mode switch to the REG position with the power cord connected.
2.
Remove the printer cover.
3.
Press the
F
key to advance the journal paper until its printed part is out of
the way.
4.
Cut the paper and remove the take-up spool.
5.
Cut the paper behind the printer and near the paper roll.
6.
Press the
F
key until the paper remaining in the printer comes out
completely.
7.
Remove the paper roll from the paper roll cradle.
Do not pull the paper through the printer.
8.
Remove the outer side of the take-up spool as shown
on the left.
on the left.
9.
Remove the printed journal roll from the take-up spool.
Area to
cut
cut
A201_5 OPERATOR MAINTENANCE 01.11.11 10:24 AM Page 64
65
Installing the paper roll
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself.
1.
Turn the mode switch to the REG position with the power cord connected.
2.
Remove the printer cover.
3.
Check that the print head release lever is in the printing position.
4.
Set the paper correctly in the paper roll cradle.
5.
Insert the end of the paper into the printer until it is caught by the printer
auto-feed and comes out of the top of the printer.
If the printer does not catch the paper, feed the paper while pressing the
auto-feed and comes out of the top of the printer.
If the printer does not catch the paper, feed the paper while pressing the
F
key.
6.
When not using the take-up spool (using as receipt paper) :
• Cut off the excess paper using the edge of the inner cover, and replace the
• Cut off the excess paper using the edge of the inner cover, and replace the
printer cover. Press the
F
key to make sure that the paper end comes
out of the printer cover.
If the paper end does not come out, open the printer cover,
and pass the paper end between the paper cutter and the
paper guide of the printer, and replace the cover.
and pass the paper end between the paper cutter and the
paper guide of the printer, and replace the cover.
When using the take-up spool (using as journal paper) :
• Insert the end of the paper into the slit in the spool. (Press the
F
key to
feed more paper if required.)
• Wind the paper two or three turns around the spool shaft.
• Set the spool on the bearing, and press the
• Set the spool on the bearing, and press the
F
key to take up excess
slack in the paper.
• Replace the printer cover.
You can wind the roll paper in OP X/Z, X1/X2, and X2/Z2
modes even if you programmed so that the printer is used for
issuance of receipts. This may be convenient to wind reports.
In this case, set the roll paper to the take-up spool.
modes even if you programmed so that the printer is used for
issuance of receipts. This may be convenient to wind reports.
In this case, set the roll paper to the take-up spool.
When you want to manually install a new roll of paper while the machine is turned off, follow the
steps shown below:
steps shown below:
1.
Pull the print head release lever toward you (to the head-up position). (Refer to the diagram on page 62.)
2.
Correctly place the new paper roll into the paper roll cradle.
3.
Insert the paper end into the printer until it comes out of the printer.
4.
Return the print head release lever to its original position.
Caution: The paper cutter is mounted on the cover. Be careful not to cut yourself. Never touch the print
head immediately after printing, because the head may still be hot.
1.
Remove the printer cover.
2.
Pull the print head release lever toward you (to the head-up position). (Refer to the diagram on page 62.)
3.
Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.
4.
Return the print head release lever to its original position.
5.
Reset the paper roll correctly by following the steps in “Installing the paper roll”.
Removing a Paper Jam
6
A201_5 OPERATOR MAINTENANCE 01.11.11 10:24 AM Page 65
66
When the printed text is getting dark or faint, paper dust may be stuck to the print head. Clean the print head as
follows:
follows:
Caution:
• Never touch the print head with a tool or anything hard as it may damage
• Never touch the print head with a tool or anything hard as it may damage
the head.
• The paper cutter is mounted on the cover. Be careful not to cut yourself.
1.
Turn the mode switch to the “
” position.
2.
Remove the printer cover.
3.
Remove the inner cover that protects the printer. (Press the lever located
both sides and lift the cover up.)
both sides and lift the cover up.)
4.
Pull the print head release lever toward you (to the head-up position). (Refer
to the diagram on page 62.)
to the diagram on page 62.)
5.
Clean the print head with a cotton swab or soft rag moistened with ethyl
alcohol or isopropyl alcohol.
alcohol or isopropyl alcohol.
6.
Return the print head release lever to its original position immediately after
cleaning.
cleaning.
7.
Replace the inner cover. (Insert the side tabs of the cover into their slots and
press the cover in the printer until it is properly seated.)
press the cover in the printer until it is properly seated.)
8.
Reset the paper roll correctly by following the steps in “Installing the paper
roll”.
roll”.
The till in the register is detachable. After closing your business for the day, remove the till from the drawer and
keep the drawer open. The 5-denomination coin case is also detachable from the till. To detach the drawer, pull
it forward fully with the till removed, and remove it by lifting it up.
keep the drawer open. The 5-denomination coin case is also detachable from the till. To detach the drawer, pull
it forward fully with the till removed, and remove it by lifting it up.
The drawer automatically opens. However, when a power failure occurs or the
machine becomes out of order, slide the lever located on the bottom of the
machine in the direction of the arrow. (See the diagram at the left.)
machine becomes out of order, slide the lever located on the bottom of the
machine in the direction of the arrow. (See the diagram at the left.)
The drawer will not open if it is locked with the key.
Lever
Opening the Drawer by Hand
9
Removing the Till and the Drawer
8
Cleaning the Print Head
7
Coin case
5-denomination coin case
(detatchable)
Bill case
Bill
separator
Till
Drawer
Coin case
Print head
Roller
2
1
A201_5 OPERATOR MAINTENANCE 01.11.11 10:24 AM Page 66
Click on the first or last page to see other XE-A201 (serv.man8) service manuals if exist.