Sharp XE-A137 (serv.man3) User Manual / Operation Manual ▷ View online
75
■
Data saving
The sales data, EJ data or programming data can be saved to the SD card.
s
A
@
s
*Job no.
*Job no.
Saving data
141
All programming data
144
All RAM data
650
Sales data
750
EJ data (save and clear)
■
Data loading
The sales data, EJ data or programming data can be saved to the SD card.
s
A
@
s
*Job no.
*Job no.
Loading data
147
All programming data
148
All RAM data
NOTE
The loading operation must be circumspect in execution, the data (#147: for all programming data,
#148: for the sales data and all programming data) will be recovered with the back-up data.
■
Error message table of the SD card function
Error code
Error state and action
01
No SD memory card is found. Insert an SD memory card into the SD card slot or reinsert it
correctly.
correctly.
02
The write-protect switch on the SD memory card is in the “PROTECTED” position. Set the
switch on the “NOT PROTECTED” position.
switch on the “NOT PROTECTED” position.
03
The SD memory card is full. Delete unnecessary data from the card on a PC or replace the
card with a new one. When using a new SD memory card, be sure to format it in advance.
card with a new one. When using a new SD memory card, be sure to format it in advance.
05
The data stored in the SD memory card is incorrect. Write correct data into the SD memory
card on a PC.
card on a PC.
09
The user folder is not found. (SHARP/ECRXXX14/user folder name)
10
Over limitation of data records (Over max. record in sales or EJ data.)
99
An error other than the above mentioned has occurred while the SD memory card is
accessed. Perform the interrupted operation again from the beginning.
accessed. Perform the interrupted operation again from the beginning.
76
OPERATOR MAINTENANCE
1
In Case of Power Failure
When power is lost, the machine retains its memory contents and all information on sales entries.
(Note: Three alkaline batteries must be installed.)
(Note: Three alkaline batteries must be installed.)
• When power failure is encountered in register idle state or during an entry, the
machine returns to normal operation after power recovery.
• When power failure is encountered during a printing cycle, the register prints
“============” and then carries out the correct printing procedure after power
recovery. (See the sample print.)
recovery. (See the sample print.)
2
In Case of Printer Error
If the printer runs out of paper, the printer will stall, and “
” will appear on the display. Key entries
will not be accepted. Refer to section 5 in this chapter, install a new roll, then press the
l
key. The printer will
print the power failure symbol and resume printing.
3
Cautions in Handling the Printer and Recording Paper
■
Cautions in handling the printer
• Avoid dusty and humid environments, direct sunlight and iron powder. (A permanent magnet and electromagnet
are used in this machine.)
• Never pull the paper when the print roller arm is locked. First lift up the arm, and then remove the paper.
• Never touch the surface of the printer head and print roller.
• Never touch the surface of the printer head and print roller.
■
Cautions in handling the recording paper (thermal paper)
• Use only the paper specified by SHARP.
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid storage places. Avoid direct sunlight.
• The printed text on the paper can discolor under conditions of high humidity and temperature, exposure to the
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid storage places. Avoid direct sunlight.
• The printed text on the paper can discolor under conditions of high humidity and temperature, exposure to the
direct sunlight, contact with glue, thinner or a freshly copied blueprint, and heat caused by friction from
scratching or other such means.
scratching or other such means.
• Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed text
with a photocopier.
77
4
Replacing the Batteries
This cash register displays a low battery symbol ( ) when the batteries are low, and displays a no battery
symbol ( ) when batteries are extremely low or batteries are not installed.
symbol ( ) when batteries are extremely low or batteries are not installed.
When the low battery symbol is displayed, replace the batteries with new ones as soon as possible. The
existing batteries will be dead in about two days.
When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC adapter plug is
disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any
data stored in memory will be cleared.
existing batteries will be dead in about two days.
When the no battery symbol is displayed, replace the batteries immediately. Otherwise, if the AC adapter plug is
disconnected or a power failure occurs, all the programmed settings will be reset to the default settings and any
data stored in memory will be cleared.
Caution: While the no battery symbol is being displayed, do not turn the mode switch to any positions.
Follow the battery replacement procedure below without changing the mode switch position.
Never pull out the AC adapter from the AC outlet, all the programmed settings will be reset to
the default settings and any data stored in memory will be cleared.
NOTE
Be sure to observe precautions shown on page 1 when handling batteries.
To replace the batteries:
1.
Make sure that the cash register is plugged in.
2.
Remove the printer cover.
3.
Open the battery compartment cover next to the paper roll cradle and
remove the old batteries.
4.
Install three new alkaline batteries LR6 (“AA” size) in the battery
compartment. Be sure the positive and negative poles of each battery are
facing in the proper direction. When they are installed correctly, the “ ”
or “ ” symbol will disappear.
facing in the proper direction. When they are installed correctly, the “ ”
or “ ” symbol will disappear.
5.
Close the battery compartment cover.
6.
Replace the printer cover.
78
5
Replacing the Paper Roll
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls other than those specified could cause paper jamming, resulting in register
malfunction.
The use of any other paper rolls other than those specified could cause paper jamming, resulting in register
malfunction.
Paper specification
Paper width: 57.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality: High quality (0.06 to 0.08 mm thickness)
Max. outside diameter: 80 mm
Quality: High quality (0.06 to 0.08 mm thickness)
• Be sure to set the paper roll prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful to set the roll correctly.
(How to set the paper roll)
To the printer
Incorrect
To the printer
Correct
■
Removing the paper roll
When a red dye appears on the paper roll, it is time to replace it. Replace the paper roll with a new one. If you
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
plan on not using the register for an extended period of time, remove the paper roll, and store it in an appropriate
place.
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
Print roller arm
1.
Remove the printer cover.
2.
Lift up the print roller arm.
3.
Remove the paper roll from the paper roll cradle.
NOTE
Do not pull the paper through the printer.
■
Installing the paper roll
For information on how to install paper rolls, refer to “Installing a Paper Roll” on page 9.
Caution: The paper cutter is mounted on the printer cover. Be careful not to cut yourself.
Click on the first or last page to see other XE-A137 (serv.man3) service manuals if exist.