Sharp ER-A410 / ER-A420 (serv.man4) Service Manual ▷ View online
ER-A410/ER-A420
OP X/Z, X1/Z1,X2/Z2 MODE
3 – 3
*
8 The stacked report function enables different reports to be printed
successively with a single reporting operation.
The programming for the stacked reports can be accomplished by
performing the following key operation in the PGM2 mode.
Stacked reports can be printed by performing the following key
operation in the X1/Z1 and X2/Z2 modes.
If the job code of a report that cannot be involved in stacked reports
is programmed, it is ignored (that report is not printed).
is programmed, it is ignored (that report is not printed).
Also, if stacked reports include any other reports for which no Z
reports can be taken, the Z reports of them are ignored and not
printed.
A maximum of 15 different reports can be printed successively with
a single reporting operation.
Those 15 reports can include those reports that are identical in
Those 15 reports can include those reports that are identical in
code number. In this case, however, if any data changes due to the
printing of the previous report, the changed data is printed on the
following report.
following report.
For example:
*
9 Reading display only.
The displayed amount can be cleared by [CL] key.
*
10 To read respective contents, it is necessary to follow the proce-
dure below.
[Action]
Individual counters for the following Z reports are incremented when
those reports are printed.
1) General daily total report (Z1)
2) General periodic total report (Z2)
3) Hourly report (Z1)
4) Daily net total report (Z2)
5) PLU report (Z1/Z2)
6) Individual Cashier and All Cashier report (Z1/Z2)
7) Individual Clerk and All Clerk report (Z1/Z2)
[Additional function]
(1) Secret code entry
When printing reports in the X1/Z1 mode and X2/Z2 mode, a secret
code must be entered prior to performing key operations to take
code must be entered prior to performing key operations to take
reports.
The secret code can be entered following the procedure shown
below.
(2) Overflow mark
If the amount or quantity in any totalizer other than GT to be printed
on X or Z reports exceeds a programmed limit, the indication mark
(overflow mark) is printed for the totalizer concerned.
The overflow mark may be printed even if a totalizer does not reach
the maximum amount. This occurs, for example, when the amount
or quantity in the totalizer gets smaller than the maximum amount
due to the entry of a negative amount after the overflowing of the
due to the entry of a negative amount after the overflowing of the
totalizer. This means that when the totalizer overflows once, the
overflow mark (for example, “!!”) is printed.
(3) MODE TITLE
Each report is printed MODE TITLE at a header of report.
There are follows.
There are follows.
(4) Report cancel function
All report printing can be able to stopped.
It can be cancelled by turned the mode switch to MGR position
It can be cancelled by turned the mode switch to MGR position
while the data is printed. (In this case, the contents of memory are
not cleared.)
<Print sample of Report cancel>
Consecutive number: The counter is incremented by one.
Z report:
Data is reset to zero.
2620
XX
JOB No.
START CODE
END CODE
SSSSSS
ST
EEEEEE
TL
ALL DELETE
NEXT JOB
NO RANGE
x90
TL
Reading
Resetting
KEY
CL
(Display amount)
(Display initialize)
JOB#
EURO STATUS
TL
Current Status Reading
Status Change Excuting
COUNTER: Max. 5 (-99999~+99999)
Q’TY:
Max. 7 (-9999999~+9999999)
AMOUNT:
Max. 9 (-999999999~+999999999)
OPX report
#041
*
OPX
*
OPZ report
#041
*
OPZ
*
X1 report
#141
*
X 1
*
Z1 report
#141
*
Z 1
*
X2 report
#241
*
X 2
*
Z2 report
#241
*
Z 2
*
:
:
:
*
*
*
*
*
*
1
the report cancel symbol
123456789012345678901234
XXX
Secret code
TL
TL
ER-A410/ER-A420
CHANGING EURO FUNCTION (X2/Z2 mode JOB)
4 – 1
CHAPTER 4. CHANGING EURO FUNCTION (X2/Z2 mode JOB)
This job is own to be able to be changed easily from local currency
system to EURO currency system in X2/Z2 mode.
(Reading the current EURO status)
<X2/Z2 mode>
(Changing EURO Function)
<X2/Z2 mode>
X: 1 = EURO STATUS (B)
2 = EURO STATUS (C)
3 = EURO STATUS (D)
[About EURO STATUS]
It is executing automatically to change from status (A) to status (B), (C),
(D).
Selectable type is one of below 4 types.
And the selectable type is decided as below for each status.
Marked “
o
” is selectable
<Action>
It is executed some of below JOBs which is needed for each status.
1) Issue General Z1 report.
2) Issue General Z2 report.
3) Clear GT 1/2/3 and Training GT.
4) Convert the unit price of DEPT / PLU from LOCAL currency to
EURO.
If new unit price is over the max digits, its price is set as “0.00”.
5) Convert the HALO amount and HALO digits from LOCAL currency
to EURO. If new HALO amount is over the max digits, its price is set
as “0.00”.
6) Change PGM function “EX1 AMOUNT PRINTING FOR TOTAL
AND CHANGE YES / NO”.
7) Change PGM function “EX1 AMOUNT PRINTING FOR TOTAL VP
YES / NO”.
8) Change PGM function “EX1” CALCULATTION METHOD DIVISION
/ MULTIPLICATION”.
9) Set “Domestic currency symbol” as EURO SYMBOL.
10) Set “Domestic TAB” as “2”.
11) Set “EX1 currency symbol” as the suitable data.
12) Set “EX1 TAB” as the suitable data.
13) Set “Rounding SYSTEM (Denmark / Sweden / Normal)” as “Nor-
mal”.
14) Set “Rounding up / down of the unit digits of AMOUNT” as “No”.
15) Set “Lowest digit entering limitation of item” as “Arbitrary”.
16) Set “Lowest digit entering limitation of payment” as “Arbitrary”.
17) Set “Difference memory” as “No”.
18) Set “Rounding of foreign currency for EX” as “Round off (4-DOWN,
5-UP)”.(EURO Regulation)
Notes:
a) This JOB cannot set below additional EURO function automati-
cally.
Below items must be set by each PGM JOB after this job.
Below items must be set by each PGM JOB after this job.
(1) EX1 RATE
(2) “CHECK, CREDIT operation for EX1 Yes / No”
b) When the unit price is converted, the rounding method of EURO
currency is fixed as “Round off (4-DOWN, 5-UP)”. [EURO Reg-
ulation]
CURRENT STATUS
4
Selectable STATUS
(A)
(B)
(C)
(D)
(A)
—
o
o
o
(B)
—
—
o
o
(C)
—
—
—
o
(D)
—
—
—
—
800
TL
800
TL
X
ER-A410/ER-A420
CHANGING EURO FUNCTION (X2/Z2 mode JOB)
4 – 2
<Selecting type and its action>
Current status (A) :
Marked “—” is remaining the current data.
Current status (B) :
Marked “—” is remaining the current data.
CURRENT STATUS
(A)
Selected STATUS
(B)
(C)
(D)
1) General Z1 report
ISSUE
ISSUE
ISSUE
2) General Z2 report
ISSUE
ISSUE
ISSUE
3) GT1 / 2 / 3 & Training GT
—
CLEAR
CLEAR
4) Convert the unit price of DEPT / PLU
—
CONVERTING
CONVERTING
5) Convert the HALO amount and HALO digits
—
CONVERTING
CONVERTING
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
“YES”
“YES”
“No”
7) EX1 AMOUNT PRINTING FOR TOTAL VP
“YES”
“YES”
“No”
8) EX1 CALCULATTION METHOD
“DIVISION”
“MULTI.”
“MULTI”
9) Domestic currency symbol
—
[EURO]
[EURO]
10) Domestic TAB
—
“2”
“2”
11) Ex1 currency symbol
[EURO]
The Current
“Domestic currency symbol”
—
12) EX1 TAB
“2”
The Curernt
“Domestic TAB”
—
13) Rounding SYSTEM (Denmark / Sweden / Normal)
—
“Normal”
“Normal”
14) Rounding up / down of the unit digits of AMOUNT
—
“No”
“No”
15) Lowest digit entering limitation of item
—
“Arbitrary”
“Arbitrary”
16) Lowest digit entering limitation of payment
—
“Arbitrary”
“Arbitrary”
17) Difference memory
—
“No”
“No”
18) Rounding of foreign currency for EX
(This method is fixed by the software)
(This method is fixed by the software)
“ROUND OFF
(4DOWN-5UP)”
“ROUND OFF
(4DOWN-5UP)”
“ROUND OFF
(4DOWN-5UP)”
CURRENT STATUS
(B)
Selected STATUS
(C)
(D)
1) General Z1 report
ISSUE
ISSUE
2) General Z2 report
ISSUE
ISSUE
3) GT1 / 2 / 3 & Training GT
CLEAR
CLEAR
4) Convert the unit price of DEPT / PLU
CONVERTING
CONVERTING
5) Convert the HALO amount and HALO digits
CONVERTING
CONVERTING
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
"YES"
"No"
7) EX1 AMOUNT PRINTING FOR TOTAL VP
"YES"
"No"
8) EX1 CALCULATTION METHOD
"MULTI."
"MULTI"
9) Domestic currency symbol
[EURO]
[EURO]
10) Domestic TAB
"2"
"2"
11) Ex1 currency symbol
The Current
"Domestic currency symbol"
[SPACE]
12) EX1 TAB
The Curernt
"Domestic TAB"
—
13) Rounding SYSTEM (Denmark / Sweden / Normal)
"Normal"
"Normal"
14) Rounding up / down of the unit digits of AMOUNT
"No"
"No"
15) Lowest digit entering limitation of item
"Arbitrary"
"Arbitrary"
16) Lowest digit entering limitation of payment
"Arbitrary"
"Arbitrary"
17) Difference memory
"No"
"No"
18) Rounding of foreign currency for EX
(This method is fixed by the software)
"ROUND OFF
(4DOWN-5UP)"
"ROUND OFF
(4DOWN-5UP)"
ER-A410/ER-A420
CHANGING EURO FUNCTION (X2/Z2 mode JOB)
4 – 3
Current status (C) :
Marked “—” is remaining the current data.
CURRENT STATUS
(C)
Selected STATUS
(D)
1) General Z1 report
ISSUE
2) General Z2 report
ISSUE
3) GT1 / 2 / 3 & Training GT
—
4) Convert the unit price of DEPT / PLU
—
5) Convert the HALO amount and HALO digits
—
6) EX1 AMOUNT PRINTING FOR TOTAL AND CHANGE
"No"
7) EX1 AMOUNT PRINTING FOR TOTAL VP
"No"
8) EX1 CALCULATTION METHOD
"MULTI"
9) Domestic currency symbol
[EURO]
10) Domestic TAB
"2"
11) Ex1 currency symbol
[SPACE]
12) EX1 TAB
----
13) Rounding SYSTEM (Denmark / Sweden / Normal)
—
14) Rounding up / down of the unit digits of AMOUNT
—
15) Lowest digit entering limitation of item
—
16) Lowest digit entering limitation of payment
—
17) Difference memory
—
18) Rounding of foreign currency for EX
(This method is fixed by the software)
"ROUND OFF
(4DOWN-5UP)"
Click on the first or last page to see other ER-A410 / ER-A420 (serv.man4) service manuals if exist.