DOWNLOAD Sharp XL-UR27H Service Manual ↓ Size: 9.68 MB | Pages: 40 in PDF or view online for FREE

 

XL-UR27H

 

2008/July/18

XL-UR27H_UK&AUS

  

 

Connect the FM aerial wire to the FM 75 OHMS socket and position the FM
aerial wire in the direction where the strongest signal can be received.

 

Placing the aerial on the unit or near the AC power lead may cause noise
pickup. Place the aerial away from the unit for better reception.

  

 

Connect the black wire to the minus (–) terminal, and the red wire to the plus
(+) terminal.

  

 

You can install the speakers either vertically or horizontally. Affix the
cushions (supplied) to the bottom of the speakers to prevent them from
sliding or falling due to vibration.

A sheet of speaker cushions (8 pcs) is supplied with this product. Use 4
cushions per speaker.

  

 

After checking all the connections have been made correctly, plug the AC
power lead of this unit into the wall socket. If you plug in the unit first, the unit
will enter the demonstration mode.

 

Unplug the AC power lead from the wall socket if the unit will not be in use
for a prolonged period of time.

 

 

Use speakers with an impedance of 8 ohms or more, as lower impedance 
speakers can damage the unit.

 

 

Do not mistake the right and the left channels. 
The right speaker is the one on the right side 
when you face the unit.

 

 

 

Do not allow any objects to fall into or to be placed 
in the bass reflex ducts.

 

 

Do not stand or sit on the speakers. You may be injured.

Red

Black

(Vertical position)

(Horizontal position)

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

 

Use an external FM aerial if you require better reception.
Consult your dealer.

Note:
When an external FM aerial is used, disconnect the supplied FM
aerial wire.

 
Precautions for battery use:

Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.

Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.

Battery removal:
Open the battery cover and pull up the battery to take out. 

The first time the unit is plugged in, the unit will enter the 
demonstration mode. You will see words scroll.

To cancel the demonstration mode:
When the unit is in the power stand-
by mode (demonstration mode),
press the X-BASS/DEMO button on
the remote control. The unit will
enter the low power consumption
mode.

To return to the demonstration mode:
When the unit is in the power stand-by mode, press the
X-BASS/DEMO button on the remote control again.
 
Note:
When the power is on, the X-BASS/DEMO button can be used to 
select the extra bass mode.

External 
FM aerial

75 ohms 
coaxial cable

 

When inserting or removing the batteries, push them towards the 

 battery terminals.

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

Replace the batteries if the operating distance is reduced or if the
operation becomes erratic. Purchase 2 “AA” size batteries
(UM/SUM-3, R6, HP-7 or similar).
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.

 

Check the remote control after checking all the connections (see
pages 8 - 10).
Point the remote control directly at the remote sensor on the unit.

The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.

Press the ON/STAND-BY button to turn the power on.

When the power is turned on, light illuminates around the display. To
turn on/off the light, hold down the CLEAR/DIMMER button on the
remote control for 2 seconds or more.

If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.

Main unit operation:
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned anti-clockwise, the volume will decrease.

0.2 m - 6 m
(8" - 20')

Remote sensor

Press the ON/STAND-BY button to enter the power stand-by mode.

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

Remote control operation:
Press the VOLUME (+ or –) button to increase or decrease the volume.

When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and “X-BASS” will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
button on the remote control.

1. Press the BASS/TREBLE button to select “BASS”.
2. Within 5 seconds, press the VOLUME (+ or –) button to adjust the

bass.

1. Press the BASS/TREBLE button to select “TREBLE”.
2. Within 5 seconds, press the VOLUME (+ or –) button to adjust the

treble.

When the FUNCTION button on main unit is pressed, the current
function will change to different mode. Press the FUNCTION button
repeatedly to select desired function.

Note:
The backup function will protect the memorised function mode for a
few hours should there be a power failure or the AC power lead
becomes disconnected.

In this example, the clock is set for the 24-hour (0:00) display.

30

MAX

MIN .....

-3    +3

-3    +3

CD

TUNER

USB

AUDIO IN

  “0:00”

The 24-hour display will appear.
(0:00 - 23:59)

  “AM 12:00”

The 12-hour display will appear.
(AM 12:00 - PM 11:59)

  “AM 0:00”

The 12-hour display will appear.
(AM 0:00 - PM 11:59)