DOWNLOAD Sharp XL-UR27H Service Manual ↓ Size: 9.68 MB | Pages: 40 in PDF or view online for FREE

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.

[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the 

 or 

  button to display the time.

The time display will appear for about 10 seconds.

After the clock setting is done, when turn the power off the unit
will automatically enter the demonstration off mode.
The “TIME ADJ” will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.

To readjust the clock:
Perform “Setting the clock” from step 1. If the “TIME ADJ” does not
appear in step 3, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.

This system can play back a standard CD, CD-R/RW in the CD format
and CD-R/RW with MP3 or WMA files, but cannot record on them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.  

This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
During VBR file playback, time counter in the display may differ
from its actual playback time.
Bitrate which is supported by MP3 is 32 ~ 320 kbps.

“MP3” and “WMA” indicator will light up after the unit reads
information on an MP3 or WMA disc.
Bitrate which is supported by WMA is 64 ~ 160 kbps.

Auto power on function:
When you press any of the following buttons, the unit turns on.

CD button on the remote control: The unit turns on and the “CD”
function is activated.
CD   /   button on the remote control: The unit turns on and CD
playback starts (regardless of the last function).
FUNCTION button on the main unit: The unit turns on and the last
function is activated (CD, TUNER, USB, AUDIO IN).
   /   button on the main unit: The unit turns on and playback of
the last function starts (CD, TUNER, USB, AUDIO IN). 

Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.

Press the 

 or 

  button once to advance the time by 1 hour. 

Hold it down to advance continuously.

Press the 

 or 

  button once to advance the time by 1 

minute. Hold it down to change the time in 5-minute intervals.

1

Clear all the programmed contents. [Refer to “Factory reset, 
clearing all memory” on page 38 for details.]

2

Perform “Setting the clock” from step 1 onwards.

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

Be sure to place 8 cm (3") disc in the middle of the spindle.

Due to the structure of the disc information, it takes longer to 
read an MP3/WMA disc than a normal CD (approximately 20 
to 90 seconds).

Playback will begin from track 1.
After the last track on the disc is played, the unit will stop
automatically.

 12 cm (5")

 8 cm (3")

Total number of 
tracks on the disc

Total playing time 
of the disc

Total number 
of files

Total Indicator

MP3 indicator

WMA 
indicator

CD Indicator

Disc play indicator

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

To remove the discs:
In the stop mode, open the disc compartment.

To pause playback:
Press the   /   (CD   /  ) button.

To stop playback:
Press the   (CD  ) button.

Do not play discs of special shapes (heart, octagon, etc.). It may
cause malfunctions.
If a disc is damaged, dirty, or loaded upside down, “NO DISC” or
“CAN’T RD” will appear on the display.
Keep foreign objects out of the disc compartment.
Subjecting the unit to shock or vibration may cause mistracking.
When the unit is not being used, be sure to close the disc
compartment. If it is left open, the lens may be covered with dust
and the unit may not operate properly.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.

Press in the stop 
mode.

Press in the playback 
mode.

Press in the playback 
mode. Press the   /     
button to resume 
playback from the 
paused point.

Press in the playback 
or stop mode.

If you press the button 
in the stop mode, 
press the   /     button 
to start the desired 
track.

Press and hold down 
in the playback mode.

Release the button to 
resume playback.

When the end of the last track is reached during fast forward,
“END” will appear on the display and CD operation will be
paused. When the beginning of the first track is reached during
fast reverse, the unit will enter the playback mode.
Rewritable multi-session discs with unfinished writing, can still be
played.
When a disc (CD, WMA or MP3) is input, “TOC READING” will be
displayed for several seconds depending on the number of files in
the disc. If this indication is displayed for an indefinite period of
time due to unspecified file being played or external noise etc.,
switch off the main AC power supply and then switch it on again.

XL-UR27H

2008/July/18

XL-UR27H_UK&AUS

By using the direct search buttons, the desired tracks on the current disc can be
played.

A track number higher than the number of tracks on the disc cannot be selected.
During random play, direct search is not possible.

Repeat play can play one track, all tracks or a programmed sequence continuously.

To cancel repeat play:
Press the PLAY MODE button again until “ ” disappears.

The tracks on the disc can be played in random order automatically.

To cancel random play:
Press the PLAY MODE button. “RND” indicator will disappear.
Notes:

If you press the 

 button during random play, you can move to the track selected

next by the random operation. On the other hand, the 

 button does not allow

you to move to the previous track. The beginning of the track being played will be
located.
In random play, the unit will select and play tracks automatically. (You cannot
select the order of the tracks.)
After all track on the disc is played, the unit will stop automatically.

Caution:
After performing repeat play, be sure to press the   (CD  ) button. Otherwise, the
disc will play continuously.

Selected track number

The direct search buttons allow you to select up to number 9.

When selecting number 10 or higher, use the “+10” button.

1 Press the “+10” button once.

2 Press the “1” button.

3 Press the “3” button.

1 Press the “+10” button twice.

2 Press the “1” button.

3 Press the “3” button.

4 Press the “0” button.

To repeat one track:
Press the PLAY MODE button once. Press the   /   button.
To repeat all tracks:
Press the PLAY MODE button twice.  Press the   /   button.
To repeat desired tracks:
Perform steps 1 - 6 in “Programmed play” section on page 17 and then press the 
PLAY MODE button once.  Press the   /   button.

To random play all tracks:
Press and hold down PLAY MODE button on the remote control for 3 seconds or 
more. Press the    /   button.