Sharp CD-PC651H User Manual / Operation Manual ▷ View online
<P=003>
(Continued)
■
Disc number selection
1
When stopped, press the DISC SKIP button.
2
Press the
0/R
(
0R
) button.
●
The next disc playback will begin, after which each following
disc will be played sequentially.
disc will be played sequentially.
Notes:
●
When the DISC SKIP button is pressed during playback, play-
back will begin automatically from the next disc. (It is not
necessary to press the
back will begin automatically from the next disc. (It is not
necessary to press the
0/R
(
0R
) button.)
●
When one of the disc number buttons ( 1- 3) is pressed
during playback, playback of the selected disc will begin auto-
matically. (It is not necessary to press the
during playback, playback of the selected disc will begin auto-
matically. (It is not necessary to press the
0/R
(
0R
) button.)
■
APSS (Auto Program Search System)
APSS automatically locates the beginning of any track.
To listen again to the track being played:
Press the
Press the
5
button for less than 0.5 seconds during playback.
To move to the beginning of the next track:
Press the
Press the
4
button for less than 0.5 seconds during playback.
●
To skip a number of tracks at one time, press the
5
or
4
button repeatedly until the desired track number is shown.
●
To start playback from a desired track, press the
5
or
4
button whilst in the stop mode to select the track number,
and then press the
and then press the
0/R
(
0R
) button.
Note:
●
APSS can only search for music on a single disc.
■
Cue and review
1
Load a disc and begin playback.
2
Hold down the
2
button for audible fast forward, and hold
down the
3
button for audible fast reverse.
3
Normal playback will resume when the
3
or
2
button is
released.
Notes:
●
When the end of the disc is reached whilst cueing, "END" will
appear in the display. (Even though the next disc has been
loaded, the disc will not be switched.)
Press the
appear in the display. (Even though the next disc has been
loaded, the disc will not be switched.)
Press the
3
button for fast reverse or press the
■
(CD
■
)
button to stop CD operation.
●
If the beginning of the disc is reached whilst reviewing, the
mode will automatically switch to normal playback at that
point.
mode will automatically switch to normal playback at that
point.
■
Random play
(Remote control operation)
The tracks on the disc(s) can be played in random order
automatically.
automatically.
1
Load a disc(s) and close the disc tray.
2
Press the RANDOM button to begin random play.
●
"R" will appear.
Notes:
●
When using random play, be sure to press the
■
(CD
■
) button after you are through listening.
Otherwise, the disc(s) will play continuously.
●
In random play the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
automatically. (You cannot select the order of the
tracks.)
To cancel random play:
Press the
0/R
(
0R
) button.
●
"R" will go out.
CD
DISC SKIP
DISC SKIP
RANDOM
CD-PC651H(SUK) TINSE0262AWZZ
12
HK
<P=001>
(Continued)
■
APMS
(Automatic Programmable Music Selector)
(Automatic Programmable Music Selector)
You can playback the tracks on the CDs in the disc 1 - 3 positions
in any order desired. By specifying the disc numbers from 1 to
3, and the track numbers from 1 to 99, you can choose up to
32 selections for playback in the order you like.
in any order desired. By specifying the disc numbers from 1 to
3, and the track numbers from 1 to 99, you can choose up to
32 selections for playback in the order you like.
1
When in the stop mode, use the disc number buttons ( 1
- 3) to select the desired disc number.
- 3) to select the desired disc number.
2
Press the
5
or
4
button to select the desired track.
3
Press the MEMORY/SET (MEMORY) button.
●
"MEMORY" will appear to show that the programmed se-
quence is being entered into memory.
quence is being entered into memory.
4
Repeat steps 1 - 3 for any other track. Up to 32 tracks can
be programmed.
be programmed.
●
If you make a mistake whilst in the programming mode
("MEMORY" will appear) or if you wish to change your selec-
tions, the programmed tracks can be cleared by pressing the
CLEAR button. The tracks will be cleared sequentially, starting
with the last track entered.
("MEMORY" will appear) or if you wish to change your selec-
tions, the programmed tracks can be cleared by pressing the
CLEAR button. The tracks will be cleared sequentially, starting
with the last track entered.
5
Press the
0/R
(
0R
) button to start playback of programmed
selections.
To clear the programmed selections:
Press the CLEAR button on the remote control whilst the disc is
stopped.
stopped.
●
Each time the button is pressed, one track will be cleared,
beginning with the last track programmed.
beginning with the last track programmed.
Notes:
●
Opening the disc tray automatically cancels the programmed
sequence.
sequence.
●
Even if you press the ON/STAND-BY button to enter the
stand-by mode or the function is changed from CD to some
other function, the programmed selections will not be cleared.
stand-by mode or the function is changed from CD to some
other function, the programmed selections will not be cleared.
●
During APMS operation, random play is not possible.
■
Repeat play
All tracks on up to 3 discs, or a programmed sequence can be
continuously repeated.
continuously repeated.
To repeat all tracks on up to 3 discs:
Press the
0/R
(
0R
) button twice.
●
"
R
" will appear.
To repeat a programmed sequence:
1
Programme a sequence of up to 32 tracks.
2
Press the
0/R
(
0R
) button twice.
●
"
R
" will appear.
To cancel repeat play:
Press the
0/R
(
0R
) button again.
●
"
R
" will go out.
Note:
●
When using repeat play, be sure to press the
■
(CD
■
) button
after you are through listening.
Otherwise, the CD(s) will play continuously.
Otherwise, the CD(s) will play continuously.
CLEAR
3
2
5
1
2
5
3
Selected disc number
Selected track number
Playback order
Repeat play indicator
CD-PC651H(SUK) TINSE0262AWZZ
13
<P=002>
2,3,5,6
1
4
RADIO OPERATION
■
Tuning
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button.
3
Press the TUNER (BAND) button to select the desired fre-
quency band. (FM ST, FM or AM)
quency band. (FM ST, FM or AM)
4
Press the TUNING/TIME (
X
or
W
) button to tune into the
desired station.
Manual tuning:
Press the TUNING/TIME (
X
or
W
) button as many times as
required to adjust the frequency shown on the display to the
frequency of the desired station.
frequency of the desired station.
Auto tuning:
When the TUNING/TIME (
X
or
W
) button is pressed for more
than 0.5 seconds, scanning will start automatically and the tuner
will stop at the first receivable broadcast station.
will stop at the first receivable broadcast station.
Notes:
●
When radio interference occurs during auto scan tuning, auto
scan tuning may stop automatically at that point.
scan tuning may stop automatically at that point.
●
If a weak station signal is found during auto scan tuning, the
station will be skipped.
station will be skipped.
●
To stop the auto tuning, press the TUNING/TIME (
X
or
W
)
button again.
●
When an RDS (Radio Data System) station is tuned in, the
frequency will be displayed first, and then the RDS indicator
will light, Finally, the station name will appear.
frequency will be displayed first, and then the RDS indicator
will light, Finally, the station name will appear.
5
To receive an FM stereo transmission, press the TUNER
(BAND) button so that the "ST" indicator on the display lights
up.
(BAND) button so that the "ST" indicator on the display lights
up.
●
"
j
" will appear when an FM broadcast is in stereo.
6
If the FM reception is weak, press the TUNER (BAND) button
so that the "ST" indicator goes out.
so that the "ST" indicator goes out.
●
The reception changes to monaural, the sound becomes
clearer.
clearer.
After use:
Press the ON/STAND-BY button to enter the stand-by mode.
Note:
●
The last station tuned in will be recalled, even after changing
the tuning band or the function, or after switching the unit to
the stand-by mode.
the tuning band or the function, or after switching the unit to
the stand-by mode.
(Main unit operation)
CD-PC651H(SUK) TINSE0262AWZZ
14
<P=003>
(Continued)
2,4
3
■
Preset tuning
You can store up to 40 stations in memory (40 stations consisting
of any combination of FM and AM stations you like) and recall
them at the push of a button.
of any combination of FM and AM stations you like) and recall
them at the push of a button.
To enter stations into memory:
1
Perform steps 1 - 6 in the "Tuning" section.
2
Press the MEMORY/SET button.
●
"MEMORY" and the preset channel number will flash.
3
Within 30 seconds, press the PRESET (
W
or
X
) button to
make the preset channel number flash in the display.
●
Store the stations in memory, in order, starting with preset
channel 1.
channel 1.
4
Within 30 seconds, press the MEMORY/SET button to store
that station in the selected station preset number memory.
that station in the selected station preset number memory.
●
If the "MEMORY" and preset number indicators go out before
the station is memorised, repeat the operation from step 2.
the station is memorised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other preset stations, or to change
a preset station.
a preset station.
●
When a new station is stored in the selected station preset
number memory, the contents previously memorised will be
erased.
number memory, the contents previously memorised will be
erased.
●
To store an RDS station in memory, perform steps 2 - 4 whilst
the RDS station name is being displayed.
the RDS station name is being displayed.
To recall a memorised station:
Press the PRESET (
X
or
W
) button for less than 0.5 seconds
to select the desired station.
●
The stations (preset channel number, frequency and fre-
quency band) which have been stored in memory will appear
in the display in numerical order, irrespective of the frequency
bands.
quency band) which have been stored in memory will appear
in the display in numerical order, irrespective of the frequency
bands.
Note:
When searching for a memorised station, do not press the
PRESET button for more than 0.5 seconds.
When the PRESET button is pressed for more than 0.5 seconds,
the unit will enter the preset memory scan mode.
When searching for a memorised station, do not press the
PRESET button for more than 0.5 seconds.
When the PRESET button is pressed for more than 0.5 seconds,
the unit will enter the preset memory scan mode.
Backup function:
The backup function protects all station presets for a few hours
should there be a power failure or the AC power lead is removed
from the AC socket.
should there be a power failure or the AC power lead is removed
from the AC socket.
■
Preset memory scan
The stations saved in the preset memory can be scanned auto-
matically.
matically.
1
To scan the preset stations, press the PRESET (
X
or
W
)
button for more than 0.5 seconds.
●
The station preset number will flash and the programmed sta-
tions will be tuned in sequentially, for 5 seconds each.
tions will be tuned in sequentially, for 5 seconds each.
2
Press the PRESET (
X
or
W
) button again to stop the memory
scan at the desired station.
Note:
When the preset memory does not have any stations stored in
it, the preset memory scan will not function.
When the preset memory does not have any stations stored in
it, the preset memory scan will not function.
(Main unit operation)
1,2
1,2
CD-PC651H(SUK) TINSE0262AWZZ
15
Click on the first or last page to see other CD-PC651H service manuals if exist.