Sharp CD-PC651H User Manual / Operation Manual ▷ View online
<P=002>
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME (
X
or
W
) button to select the time
display mode.
"0:00"
→
The 24-hour display will appear.
(0:00 - 23:59)
"AM 0:00"
"AM 0:00"
→
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"AM 12:00"
"AM 12:00"
→
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
●
Note that this can only be set when the unit is first installed
or it has been reset (see page 28).
or it has been reset (see page 28).
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME (
X
or
W
) button to adjust the hour.
●
Press the TUNING/TIME (
X
or
W
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
matically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME (
X
o r
W
) button to adjust the
minutes.
●
Press the TUNING/TIME (
X
or
W
) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
minute intervals.
●
The hour setting will not advance even if minutes advance from
"59" to "00".
"59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" seconds.
(Seconds are not displayed.)
(Seconds are not displayed.)
To see the time display:
TUNING/
TIME
( )
TIME
( )
MEMORY/
SET
SET
CLOCK
ON/
STAND-BY
STAND-BY
AM 12:00
AM 0:00
0:00
2
3
4
7
6
5
8
9
Press the CLOCK button.
●
The time display will appear for about 5 seconds.
Note:
●
The clock display will flash on and off at the push of the CLOCK
button when the AC power supply is restored after a power
failure occurs or after the AC power lead is disconnected.
If this happens, follow the procedure below to change the clock
time.
button when the AC power supply is restored after a power
failure occurs or after the AC power lead is disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
①
Press the CLOCK button.
②
Within 5 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To change the time display mode:
①
Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 28.
COMPUTER", on page 28.
②
Perform steps 1 - 9 above.
(Main unit operation)
In this example, the clock is set for the
24-hour (0:00) system.
24-hour (0:00) system.
CD-PC651H(SUK) TINSE0262AWZZ
8
<P=003>
SOUND CONTROL
■
Volume
Press the VOLUME button to increase the volume and the
VOLUME button to decrease the volume.
VOLUME button to decrease the volume.
●
The volume display can be changed within the range of "0" to
"MAXIMUM".
"MAXIMUM".
■
Pre-programmed equalizer
When the EQUALIZER (EQUALIZER MODE) button is pressed,
the current mode setting will be displayed. To change to a dif-
ferent mode, press the EQUALIZER (EQUALIZER MODE) button
repeatedly.
the current mode setting will be displayed. To change to a dif-
ferent mode, press the EQUALIZER (EQUALIZER MODE) button
repeatedly.
FLAT
HEAVY-1
HEAVY-2
SOFT-2
SOFT-1
VOCAL
FLAT: The sound is not modified.
HEAVY-1: Bass and treble are slightly emphasised.
HEAVY-2: Bass and treble are emphasised more.
VOCAL: Vocals (midrange tones) are emphasised.
SOFT-1: Treble is cut a little.
SOFT-2: Treble is reduced a lot.
HEAVY-1: Bass and treble are slightly emphasised.
HEAVY-2: Bass and treble are emphasised more.
VOCAL: Vocals (midrange tones) are emphasised.
SOFT-1: Treble is cut a little.
SOFT-2: Treble is reduced a lot.
■
Extra bass (X-BASS)
Press the X-BASS button to emphasise the bass region of the
frequency spectrum.
"X-BASS" will appear.
Press the X-BASS button again to cancel the extra bass mode.
"X-BASS" will disappear.
frequency spectrum.
"X-BASS" will appear.
Press the X-BASS button again to cancel the extra bass mode.
"X-BASS" will disappear.
■
Balance
(Remote control operation)
Press the BALANCE
Z
(LEFT) button to decrease the level of
the right speaker, and press the BALANCE
Y
(RIGHT) button to
decrease the level of the left speaker.
VOLUME
1 ~ 10
(Main unit)
(Remote control)
(Main unit)
(Remote control)
(Main unit)
(Remote control)
0
1
2
29
30 MAXIMUM
.....
CD-PC651H(SUK) TINSE0262AWZZ
9
HK
<P=001>
(Continued)
■
Dolby Pro Logic Surround mode
Video and Laser Disc software programmes carrying the
trademark are recordings that contain the same
Dolby Surround data as used in movie theatres.
trademark are recordings that contain the same
Dolby Surround data as used in movie theatres.
The Dolby Pro Logic Surround mode uses Dolby Surround data
to bring the full presence experienced in a movie theatre into
your home.
To use this mode, you must connect the surround and centre
channel speakers.
Before playing a video (or Laser Disc) software programme car-
rying the trademark, be sure to complete the
"Dolby Pro Logic Surround setup" as follows.
to bring the full presence experienced in a movie theatre into
your home.
To use this mode, you must connect the surround and centre
channel speakers.
Before playing a video (or Laser Disc) software programme car-
rying the trademark, be sure to complete the
"Dolby Pro Logic Surround setup" as follows.
Dolby Pro Logic Surround setup:
(Remote control operation)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the DOLBY PRO LOGIC button.
●
The NORMAL or PHANTOM button will light.
3
Select the centre mode using the CENTER MODE button.
NORMAL: The centre speaker is used.
PHANTOM: Use this mode when a centre speaker is not
connected. The centre channel signals are
output through the front speakers.
PHANTOM: Use this mode when a centre speaker is not
connected. The centre channel signals are
output through the front speakers.
●
The selected centre mode is automatically stored in memory
and will be used the next time you activate DOLBY PRO
LOGIC or until it is changed.
and will be used the next time you activate DOLBY PRO
LOGIC or until it is changed.
4
Press the TEST TONE button.
●
The test tone is a tone that moves from one speaker to the
next, taking 2 seconds to go from speaker to speaker.
next, taking 2 seconds to go from speaker to speaker.
In NORMAL mode:
Left (L ch)
Centre (C ch)
Right (R ch)
Surround (S ch)
In PHANTOM mode:
Left (L ch)
Right (R ch)
Surround (S ch)
5
Adjust the centre speaker volume or the volume of the sur-
round speakers.
round speakers.
To adjust the centre speaker volume to match the level of
the front speakers:
the front speakers:
Press the CENTER LEVEL
W
button to increase the volume and
the CENTER LEVEL
X
button to decrease the volume.
To adjust the volume of the surround speakers to match
the level of the front speakers:
Press the SURROUND LEVEL
the level of the front speakers:
Press the SURROUND LEVEL
W
button to increase the volume
and the SURROUND LEVEL
X
button to decrease the volume.
6
After adjusting the speaker volume, press the TEST TONE
button.
button.
●
The test tone will stop.
Notes:
●
Be sure to adjust the sound from your favorite listening posi-
tion.
tion.
●
The volume is adjusted in 1 dB steps up or down each time
you press the CENTER LEVEL button or the SURROUND
LEVEL button.
you press the CENTER LEVEL button or the SURROUND
LEVEL button.
●
The volume settings for the centre and surround speakers are
stored in memory for future use. However, if the power is
disconnected or there is a power failure, the levels will return
to their initial settings.
stored in memory for future use. However, if the power is
disconnected or there is a power failure, the levels will return
to their initial settings.
ON/
STAND-BY
TEST
TONE
DOLBY
PRO LOGIC
CENTER
MODE
CENTER
LEVEL
LEVEL
SURROUND
LEVEL
LEVEL
-10 -9 0 +9 +10
Dolby Pro Logic Surround playback:
1
Press the NORMAL or PHANTOM button on the
main unit or the DOLBY PRO LOGIC button on the
remote control.
main unit or the DOLBY PRO LOGIC button on the
remote control.
●
The NORMAL or PHANTOM button will illuminate,
and the unit will enter the Dolby Pro Logic Surround
mode.
and the unit will enter the Dolby Pro Logic Surround
mode.
2
Select the centre mode using the CENTER MODE
button.
button.
NORMAL: The centre speaker is used.
PHANTOM: Use this mode when a centre speaker
is not connected. The centre channel
signals are output through the
front speakers.
PHANTOM: Use this mode when a centre speaker
is not connected. The centre channel
signals are output through the
front speakers.
3
Play the video software programme.
4
To cancel the Dolby Pro Logic Surround mode, press
the BYPASS button on the main unit or the DOLBY
PRO LOGIC button on the remote control.
the BYPASS button on the main unit or the DOLBY
PRO LOGIC button on the remote control.
●
The BYPASS button will light.
Notes:
●
You cannot use the Dolby Pro Logic Surround fea-
ture with headphones.
ture with headphones.
●
If you use headphones, cancel the Dolby Pro Logic
Surround mode.
Even after the headphones are connected, if the unit
is in the Dolby Pro Logic Surround mode, sound will
still be heard from the surround and centre speakers.
Surround mode.
Even after the headphones are connected, if the unit
is in the Dolby Pro Logic Surround mode, sound will
still be heard from the surround and centre speakers.
Front
speaker
(Left)
speaker
(Left)
Centre speaker
Front
speaker
(Right)
speaker
(Right)
Surround
speaker
(Left)
speaker
(Left)
Surround
speaker
(Right)
speaker
(Right)
CD-PC651H(SUK) TINSE0262AWZZ
10
<P=002>
COMPACT DISC OPERATION
■
CD playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
4
Place the CD(s) on the disc tray, label side up.
●
CDs can be placed on any open position on the disc tray.
●
Be sure to place 8 cm (3") CD(s) in the middle of the disc
trays.
trays.
Caution:
Do not stack CDs in the tray.
This can damage the player and the CDs.
Do not stack CDs in the tray.
This can damage the player and the CDs.
5
When loading a third disc, press the DISC SKIP button to turn
the disc tray, then place the CD in the open position.
the disc tray, then place the CD in the open position.
6
Press the OPEN/CLOSE button to close the disc tray.
●
The total number of tracks and the total playing time for one
disc will be displayed. At this time, the disc number indicator
is flashing.
disc will be displayed. At this time, the disc number indicator
is flashing.
7
Press the desired disc number button ( 1 - 3).
8
Press the
0/R
(
0R
) button.
●
Playback will begin from track 1 on the disc you have selected
to play.
to play.
●
After the disc finishes playing, the next disc will automatically
play.
play.
●
When there is no CD in one of the disc 1 - 3 positions, that
position will be skipped and the next CD will be played.
position will be skipped and the next CD will be played.
●
When the last track on the third disc has finished playing, the
unit will stop automatically.
unit will stop automatically.
To interrupt playback:
①
Press the CD
6
button on the remote control.
●
"
6
" will appear.
②
Press the
0R
button to resume playback from the same
point.
To stop playback:
Press the
■
(CD
■
) button.
To remove the CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
●
The disc tray will open. Remove the two discs. Then, press
the DISC SKIP button to rotate the disc tray and remove the
remaining disc.
the DISC SKIP button to rotate the disc tray and remove the
remaining disc.
After use:
Press the ON/STAND-BY button to enter the stand-by mode.
Caution:
●
Do not carry the unit with discs left in the
disc trays. The discs may come loose inside
the unit and they may be damaged or cause
damage to the unit. This may also cause mal-
functions.
disc trays. The discs may come loose inside
the unit and they may be damaged or cause
damage to the unit. This may also cause mal-
functions.
●
Do not place two CDs in one disc position.
●
Do not push the disc tray whilst it is moving.
●
Do not attempt to turn the disc tray by hand. This
may cause malfunctions.
may cause malfunctions.
●
If the power fails whilst the tray is open, wait until
the power is restored.
the power is restored.
●
If the disc tray is stopped forcibly, "ERR" will ap-
pear in the display and the unit will not function.
If this occurs, press the ON/STAND-BY button to
enter the stand-by mode and then turn the power
on again.
pear in the display and the unit will not function.
If this occurs, press the ON/STAND-BY button to
enter the stand-by mode and then turn the power
on again.
●
If TV or radio interference occurs during CD oper-
ation, move the unit away from the TV or radio.
ation, move the unit away from the TV or radio.
●
If a disc is damaged, dirty, or loaded upside
down, the disc will be skipped and the next disc
will automatically play.
down, the disc will be skipped and the next disc
will automatically play.
CD
CD
4
5
7
5 3,6
1
2
8
5
8
2
1
12 cm (5")
8 cm (3")
CD-PC651H(SUK) TINSE0262AWZZ
11
Click on the first or last page to see other CD-PC651H service manuals if exist.