Sharp CD-PC651H User Manual / Operation Manual ▷ View online
<P=003>
(Continued)
TAPE 1
TAPE 2
PUSH
EJECT
PUSH
EJECT
1
2,5
6
4
3
1
6
6
4
2,5
3
In the following cases, the EON stand-by mode will be
cancelled.
cancelled.
●
When the unit is set in the stand-by mode
●
When the unit is switched to another band in the
EON stand-by mode
EON stand-by mode
●
When you change the FM station whilst in the EON
stand-by mode
stand-by mode
●
When a preset call is made
Notes:
●
During the same programme as the specified PTY
(or TA) is being broadcast on the station you are
receiving, the unit will not switch to other network
station.
(or TA) is being broadcast on the station you are
receiving, the unit will not switch to other network
station.
●
If there are more than two other network stations
you want to listen to, compare the strength of each
station’s signal and tune in the station with the stron-
gest signal. (EON-AF)
However, if the frequency of other network station
has been stored in the preset channel memory, the
unit will switch to that preset channel.
you want to listen to, compare the strength of each
station’s signal and tune in the station with the stron-
gest signal. (EON-AF)
However, if the frequency of other network station
has been stored in the preset channel memory, the
unit will switch to that preset channel.
●
If you want to cancel the reception of an ON (other network)
station which was tuned in by the EON system and return to
the original station you were receiving, press the EON button.
station which was tuned in by the EON system and return to
the original station you were receiving, press the EON button.
●
After the unit returns to the original station, the stand-by mode
will still be active. (The "TI" or "PTY" will remain lit.)
will still be active. (The "TI" or "PTY" will remain lit.)
●
The unit will not switch from the ON station to another network
station. The unit returns to the original station.
station. The unit returns to the original station.
●
When the unit switches automatically to "other network" sta-
tion, if there is any problem with this station or the station
cannot be received properly "WEAK SIG" will appear and the
unit will return to the original station.
tion, if there is any problem with this station or the station
cannot be received properly "WEAK SIG" will appear and the
unit will return to the original station.
●
Even if the unit switches from the station you are listening to
directly to some "other network" station, if the signals from
the other network stations are very weak, the unit will search
for the station with the strongest signal and switch to it.
However, if the signals from all the other network stations are
very weak, or if the tuning conditions are very bad (due to
electrical noise), the unit will stop searching, "WEAK SIG" will
be displayed, and the unit will return to the original station
you were receiving.
directly to some "other network" station, if the signals from
the other network stations are very weak, the unit will search
for the station with the strongest signal and switch to it.
However, if the signals from all the other network stations are
very weak, or if the tuning conditions are very bad (due to
electrical noise), the unit will stop searching, "WEAK SIG" will
be displayed, and the unit will return to the original station
you were receiving.
CASSETTE OPERATION
■
TAPE 1 or TAPE 2 playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TAPE (1
V
2) button.
3
Open the cassette door by pushing the area marked "PUSH
EJECT".
EJECT".
4
Load the cassette into the TAPE 1 or TAPE 2 cassette com-
partment.
partment.
5
With cassettes in both decks, press the TAPE (1
V
2) button
to switch operation from one deck to the other.
6
Press the
0/R
button to start playback.
●
When playback is performed using the remote control, press
the TAPE 1 or TAPE 2
the TAPE 1 or TAPE 2
0
button.
To stop playback:
Press the
■
(TAPE
■
) button.
Fast forward/rewind: (TAPE 2 only)
①
Press the
■
(TAPE
■
) button, then press the TAPE (1
V
2)
button to select TAPE 2.
②
To advance the tape, press the
2
button.
To rewind it, press the
3
button.
Caution:
●
To remove the cassette tape, press the
■
(TAPE
■
) button,
and then open the cassette compartment.
●
Before changing from one tape operation to another, press
the
the
■
(TAPE
■
) button.
●
If a power failure occurs during tape operation, the tape head
will remain engaged with the tape and the cassette door will
not open. In this case, wait until power is restored.
will remain engaged with the tape and the cassette door will
not open. In this case, wait until power is restored.
CD-PC651H(SUK) TINSE0262AWZZ
24
<P=004>
RECORDING
●
When recording important selections, be sure to
make a preliminary test to ensure that the desired
material is being properly recorded.
make a preliminary test to ensure that the desired
material is being properly recorded.
●
The volume and sound effect controls may be ad-
justed with no effect on the recorded signal. (Variable
Sound Monitor)
justed with no effect on the recorded signal. (Variable
Sound Monitor)
●
Metal and CrO
2
tapes should not be used for recording or
dubbing.
●
To erase a recorded tape, press the TAPE (1
V
2) button to
select TAPE 2, press the REC PAUSE (
●
6
) button, and
finally press the
0
/
R
(TAPE 2
0
) button.
(Check to make sure that TAPE 1 is not being used.)
■
Recording from the built-in CD player
(CD Synchronised Recording System)
(CD Synchronised Recording System)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button and load the desired disc.
●
Use the APMS function to store the tracks you want to record
in memory. (See page 13.)
in memory. (See page 13.)
3
Load a cassette into the TAPE 2 cassette compartment.
4
Press the REC PAUSE (
●
6
) button.
●
"SYNC" and "REC" will flash.
5
Press the
0 /R
(TAPE 2
0
) button.
●
"REC" will appear.
●
CD playback will start approximately 5 seconds after the tape
starts.
starts.
To stop recording:
Press the
■
(CD
■
) button.
The CD and tape will stop.
Note:
●
When the end of the tape is reached whilst recording, the CD
player will display the track number which was being played
at that time, and stop automatically.
player will display the track number which was being played
at that time, and stop automatically.
TAPE
TAPE2
TUNER
(BAND)
(BAND)
REC PAUSE
CD
ON/
STAND-BY
ON/
STAND-BY
CD
CD
TUNER
(BAND)
(BAND)
TAPE
(1 2)
(1 2)
TAPE(1 2)
TAPE 1
TAPE 2
If you want to restart recording from the interrupted track, turn
over the tape, press the REC PAUSE (
over the tape, press the REC PAUSE (
●
6
) button and then
the
0
/
R
(TAPE 2
0
) button.
(If tracks have been stored in memory using the APMS func-
tion, recording will restart from the first track stored in mem-
ory.)
tion, recording will restart from the first track stored in mem-
ory.)
■
Dubbing from tape to tape
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette into the TAPE 1 cassette com-
partment. Insert a blank tape into the TAPE 2 cassette com-
partment.
partment. Insert a blank tape into the TAPE 2 cassette com-
partment.
●
It is recommended that the recording tape be the same length
as the master tape.
as the master tape.
3
Press the TAPE (1
V
2) button until "TAPE 1" appears in the
display.
4
Press the REC PAUSE (
●
6
) button.
5
Press the
0 / R
(TAPE 2
0
) button.
To stop dubbing:
Press the
■
(TAPE
■
) button.
●
TAPE 1 and TAPE 2 will simultaneously stop.
■
Recording from the built-in radio
1
Tune in to the desired station. (See pages 14-15.)
2
Load a cassette into the TAPE 2 cassette compart-
ment.
ment.
3
Press the REC PAUSE (
●
6
) button.
●
"REC" will flash.
4
Press the
0 / R
(TAPE 2
0
) button.
●
"REC" will appear.
Note:
●
If a whistling noise is heard whilst recording from an
AM station, move the AM loop aerial to a position
where noise is no longer heard from the unit.
AM station, move the AM loop aerial to a position
where noise is no longer heard from the unit.
To stop recording:
Press the
■
(TAPE
■
) button.
CD-PC651H(SUK) TINSE0262AWZZ
25
HK
<P=001>
HOW TO USE THE BUILT-IN TIMER
■
Timer playback
●
Before setting the timer, make sure that the clock setting is
correct. (Page 8)
correct. (Page 8)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD, TUNER (BAND), TAPE (1
V
2) or VIDEO/AUX
button to select the desired function.
3
Press the TIMER/SLEEP button repeatedly until a green "
f
"
is displayed.
●
The timer set indicator will flash.
4
Press the TUNING/TIME (
X
or
W
) button to set the hour
start time, then press the MEMORY/SET button.
5
Press the TUNING/TIME (
X
or
W
) button to set the minute
start time, then press the MEMORY/SET button.
●
The power will be automatically turned off, and the timer set
indicator will light up.
indicator will light up.
6
When the preset time is reached, the volume will increase
gradually until it reaches the volume you were listening to
before turning off the unit.
gradually until it reaches the volume you were listening to
before turning off the unit.
7
If you select CD or TAPE during timer playback, the power
will be turned off after the tape or CD is finished playing back.
If you select TUNER or VIDEO/AUX, the power will be turned
off one hour later.
will be turned off after the tape or CD is finished playing back.
If you select TUNER or VIDEO/AUX, the power will be turned
off one hour later.
■
Timer recording
1
Press the ON/STAND-BY button to turn the power on.
●
Load a cassette for recording into the TAPE 2 cassette com-
partment.
partment.
2
Press the TUNER (BAND) or VIDEO/AUX button to select the
desired function.
desired function.
3
Press the TIMER/SLEEP button repeatedly until a red "
f
" is
displayed.
●
The timer set indicator will flash.
4
Press the TUNING/TIME (
X
or
W
) button to set the hour start
time, then press the MEMORY/SET button.
5
Press the TUNING/TIME (
X
or
W
) button to set the minute
start time, then press the MEMORY/SET button.
●
The power will be automatically turned off, and the timer set
indicator will light up.
indicator will light up.
6
When the recording tape reaches its end, the timer recording
will end, and the power will be turned off.
will end, and the power will be turned off.
●
When timer recording starts, the volume will increase gradually
until it reaches the volume you were listening to before turning
off the unit.
until it reaches the volume you were listening to before turning
off the unit.
To cancel timer operation:
Press the ON/STAND-BY button to turn the power on.
To change the programmed contents:
Start again from step 1.
Note:
●
Once the time is set, the setting will be retained until a new
time is entered.
time is entered.
■
Sleep operation
The radio, compact disc and cassette deck can all be
turned off automatically.
turned off automatically.
1
Play back the desired sound source.
2
Press the TIMER/SLEEP button repeatedly until
"SLEEP" is displayed.
"SLEEP" is displayed.
To change the sleep time:
Whilst the sleep time is displayed, press the TUN-
ING/TIME (
ING/TIME (
X
or
W
) button to adjust the time.
(Maximum: 3 hours - Minimum: 1 minute)
The amount of sleep time can also be changed during
the sleep operation.
The amount of sleep time can also be changed during
the sleep operation.
●
3 hours - 5 minutes
→
5-minute intervals
●
5 minutes - 1 minute
→
1-minute intervals
3
Press the MEMORY/SET button.
4
The unit will turn off automatically after the preset
sleep time has elapsed.
sleep time has elapsed.
Note:
●
Once the sleep time is set, it will remain the same
duration until the setting is changed.
duration until the setting is changed.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button.
To cancel the sleep operation:
Press the ON/STAND-BY button to enter the stand-by
mode.
mode.
(Main unit operation)
ON/
STAND-BY
CD
TUNER
(BAND)
(BAND)
VIDEO
AUX
TAPE
(1 2)
(1 2)
MEMORY/SET
TIMER/
SLEEP
SLEEP
TUNING/
TIME
( )
TIME
( )
3
4
5
CD-PC651H(SUK) TINSE0262AWZZ
26
<P=002>
USING EXTERNAL UNITS
■
Video/Auxiliary (Audio signal) input
To listen to or record signals from external sources
through this unit:
through this unit:
1
Use an RCA lead to connect the desired external unit to the
VIDEO/AUX 1 or 2 sockets.
(red
VIDEO/AUX 1 or 2 sockets.
(red
→
right channel, white
→
left channel)
●
When using video equipment (Laser Disc player or VCR), be
sure to connect the audio output to this unit and the video
output to a television.
sure to connect the audio output to this unit and the video
output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
●
Select either "VIDEO 1" or "VIDEO 2".
4
Operate the external unit.
5
To record the sound from the external unit, perform steps 1
- 4 of the "Recording from the built-in radio" section on page
25.
- 4 of the "Recording from the built-in radio" section on page
25.
Note:
●
To prevent hum interference, do not place this unit near tele-
vision receivers.
vision receivers.
■
CD digital output (optical)
The CD digital signal from this unit can be recorded by
other DAT or MiniDisc recorders.
other DAT or MiniDisc recorders.
1
Remove the CD DIGITAL OUT socket cover.
2
Use a commercially available digital cable to connect the unit
to the OPTICAL IN socket of a MiniDisc recorder or a DAT.
to the OPTICAL IN socket of a MiniDisc recorder or a DAT.
3
Put the external unit in the recording mode.
4
Play a CD on this unit.
Note:
●
Only CD signals can be output.
■
Headphones
●
Before plugging in or unplugging the headphones, make sure
the volume level is reduced.
the volume level is reduced.
●
Be sure your headphones have a 3.5 mm (1/8") diameter plug
and are between 16 ohms and 50 ohms impedance. The rec-
ommended impedance is 32 ohms.
and are between 16 ohms and 50 ohms impedance. The rec-
ommended impedance is 32 ohms.
●
When headphones are connected, the speakers are discon-
nected automatically. Adjust the VOLUME control for the
desired volume.
nected automatically. Adjust the VOLUME control for the
desired volume.
Note:
●
If you use headphones, cancel the Dolby Pro Logic Surround
mode.
Even after the headphones are connected, if the unit is in the
Dolby Pro Logic Surround mode, sound will still be heard from
the surround and centre speakers.
mode.
Even after the headphones are connected, if the unit is in the
Dolby Pro Logic Surround mode, sound will still be heard from
the surround and centre speakers.
To the line output socket
RCA
lead
lead
Commercially available digital cable
CD-PC651H(SUK) TINSE0262AWZZ
27
Click on the first or last page to see other CD-PC651H service manuals if exist.