DOWNLOAD Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X Service Manual ↓ Size: 3.18 MB | Pages: 38 in PDF or view online for FREE

Model
TX-23LX50M TX-23LX50A TX-23LX50X
Pages
38
Size
3.18 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD TV
File
tx-23lx50m-tx-23lx50a-tx-23lx50x.pdf
Date

Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X Service Manual ▷ View online

GLP2W Chassis
LCD TV
Specifications
Power Source
AC 110-240 V, 50 / 60 Hz
Power Consumption
Average use : 87 W
Standby condition : 0.5 W
LCD
22.9 - inch (58.3 cm)
Wide XGA (1366 × 768 pixels) 16:9 aspect ratio LCD panel.
Screen Size
508 mm (W) × 286 mm (H) (20.0” × 11.3”)
Sound
Speaker
Ø6 cm × 2 pcs, 8
W
Audio Output
6 W (3 W + 3 W), 10 % THD
Headphones
M3 (3.5 mm) Jack × 1
Receiving Systems/ Band name
Receiving Channels
Regular TV
ORDER NO. ITD0505026CE
 1 Safety Precautions 
4
 1.1. 
General Guidelines 
4
 2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 
4
 3 About lead free solder (PbF) 
5
 4 Self-check function 
6
 4.1. 
How to access 
6
 4.2. 
Screen display 
6
 5 Chassis Board Layout 
7
 6 Disassembly for Service 
8
 6.1. 
Pedestal ass 馳 
8
 6.2. 
Rear cover 
8
 6.3. 
Tuner cover and the Shield cover 
8
 6.4. 
Power unit 
9
VHF BAND
2-12 (PAL / SECAM B, K1)
0-12 (PAL B AUST.)
1-9 (PAL B N.Z.)
1-12 (PAL / SECAM D)
1-12 (NTSC M Japan)
2-13 (NTSC M USA)
UHF BAND
21-69 (PAL G, H, I / SECAM G, K, K1)
28-69 (PAL B AUST.)
13-57 (PAL D, K)
13-62 (NTSC M Japan)
14-69 (NTSC M USA)
CATV
S1-S20 (OSCAR)
1-125 (USA CATV)
C13-C49 (JAPAN)
S21-S41 (HYPER)
Z1-Z37 (CHINA)
5A, 9A (AUST.)
Aerial-Rear
UHF/ VHF
Operating Conditions
Temperature : 5 °C - 40 °C
Humidity : 5 % - 90 % RH (non-condensing)
Connection Terminals
AV1
VIDEO (RCA Pin Type)
1.0 Vp-p (75
W)
S-VIDEO (MINI DIN 4-pin)
Y: 1.0 Vp-p (75
W), C: 0.286 Vp-p (75 W)
AUDIO L-R (RCA Pin Type × 2)
0.5 Vrms
AV2
VIDEO (RCA Pin Type)
1.0 Vp-p (75
W)
AUDIO L-R (RCA Pin Type × 2)
0.5 Vrms
Y
1.0 Vp-p (including synchronization)
P
B
/ P
R
± 0.35 Vp-p
Applicable signal to AV2 Y, P
B
/ C
B
, P
R
/ C
R
input terminals: 525i / p and 625i / p
MONITOR OUT
VIDEO (RCA Pin Type)
1.0 Vp-p (75
W)
AUDIO L-R (RCA Pin Type × 2)
0.5 Vrms
Dimensions ( W × H × D )
Including TV Stand
612 mm × 505 mm × 259 mm (24.1” × 19.9” × 10.2”)
TV Set Only
612 mm × 441 mm × 125 mm (24.1” × 17.4” × 4.9”)
Weight
10.0 kg (22.0 lb.) Net
Note:
Design and specifications are subject to change without notice. Weight and Dimensions shown are approximate.
CONTENTS
 Page 
Page
2
TX-23LX50M / TX-23LX50A / TX-23LX50X
 6.5. 
A-Board 
9
 6.6. 
AP-Board 
9
 6.7. 
K-Board 
9
 6.8. 
V-Board 
10
 6.9. 
Speaker 
10
 6.10. Main chassis 
10
 6.11. LCD Panel 
10
 7 Lead of Wiring 
11
 8 Service Mode Function 
12
 8.1. 
How to enter SERVICE 1 
12
 8.2. 
How to enter SERVICE 2 
12
 8.3. 
Option Description 
14
 8.4. 
Option Code Setting 
16
 9 Adjustment 
17
 9.1. 
DVCO adjustment 
17
 10 Conductor Views 
19
 10.1. A-Board 
19
 10.2. AP-Board 
21
 10.3. K and V-Board 
22
 11 Block and Schematic Diagram 
23
 11.1. Schematic Diagram Notes 
23
 11.2. Main Block Diagram 
24
 11.3. Power Block Diagram 
25
 11.4. Signal Block Diagram 
26
 11.5. A-Board (1 of 3) Schematic Diagram 
27
 11.6. A-Board (2 of 3) Schematic Diagram 
28
 11.7. A-Board (3 of 3) Schematic Diagram 
29
 11.8. AP, K and V-Board Schematic Diagram 
30
 12 Parts Location & Mechanical Replacement Parts List 
31
 12.1. Parts Location 
31
 12.2. Packing Exploded Views 
32
 12.3. Mechanical Replacement Parts List 
33
 13 Electrical Replacement Parts List 
34
 13.1. Replacement Parts List Notes 
34
 13.2. Electrical Replacement Parts List 
35
3
TX-23LX50M / TX-23LX50A / TX-23LX50X
1.1.1. Leakage Current Cold Check
 1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
 2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1M
W and 5.2MW.
When the exposed metal does not have a return path to the
chassis, the reading must be
.
Figure 1
1.1.2. Leakage Current Hot Check (See
Figure 1.)
 1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
 2. Connect a 1.5k
W, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe, as shown in
Figure 1.
 3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
 4. Check each exposed metallic part, and measure the
voltage at each point.
 5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
 6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
1 Safety Precautions
1.1. General Guidelines
 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
 4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
4
TX-23LX50M / TX-23LX50A / TX-23LX50X
Page of 38
Display

Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X Service Manual ▷ Download

  • DOWNLOAD Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X Service Manual ↓ Size: 3.18 MB | Pages: 38 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X TV. Information contained in Panasonic TX-23LX50M / TX-23LX50A / TX-23LX50X Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.