Sharp CD-MD3000 (serv.man2) User Manual / Operation Manual ▷ View online
41
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Recording to a Cassette Tape from a CD
You can record the desired CD using the DISC 1 - DISC 6 buttons.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button and load the desired disc.
3
Load a cassette into the compartment with side A facing you.
●
When recording important selections, make a preliminary test to ensure that the
desired material is properly recorded.
desired material is properly recorded.
●
The volume and sound controls can be adjusted with no effect on the recorded
signal (Variable Sound Monitor).
signal (Variable Sound Monitor).
●
Do not use metal and CrO
2
tapes for recording.
4
Press the REV. MODE button on the remote control to choose one
side or both sides.
side or both sides.
5
Press the TAPE REC button repeatedly to switch to the side you
record on.
record on.
●
Recording will be paused.
●
To record on both sides, begin on side A. (If recording is started from side B,
the tape will not switch over to side A.)
the tape will not switch over to side A.)
6
Press one of the DISC 1 - DISC 6 buttons to start recording.
●
When the CD reaches the end, recording will stop.
Recording from several CDs continuously:
1. Follow the above steps 1 - 5.
2. Regardless of the tape setting (step 5), press the
2. Regardless of the tape setting (step 5), press the
06
button to record on side A, or
the
1
button for side B.
●
Recording will start from the lowest numbered disc.
To perform programmed recording:
1. Programme discs and tracks. (See page 22.)
2. Press the TAPE REC button.
3. Regardless of the tape setting (step 5), press the
2. Press the TAPE REC button.
3. Regardless of the tape setting (step 5), press the
06
button to record on side A, or
the
1
button for side B.
To stop recording:
Press the
■
button.
The CD and tape will stop.
Auto restart function:
If the recording side is switched from side A to B during recording, the system will
record the interrupted track on side B from its beginning.
The recording will be made without cutting the beginning of the track on side B.
record the interrupted track on side B from its beginning.
The recording will be made without cutting the beginning of the track on side B.
.... To record on both sides.
.... To record on only one side.
.... To record on only one side.
T
ape Recording
42
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Recording to a Cassette Tape from a MiniDisc
1
Press the ON/STAND-BY button to turn the power on.
2
Press the MD button and load a MiniDisc into the MD compart-
ment, label side up. (See page 36.)
ment, label side up. (See page 36.)
3
Load a cassette into the compartment with side A facing you.
4
Press the REV. MODE button on the remote control to choose one
side or both sides.
side or both sides.
5
Press the TAPE REC button repeatedly to switch to the side you
record on.
record on.
●
Recording will be paused.
●
To record on both sides, begin on side A. (If recording is started from side B,
the tape will not switch over to side A.)
the tape will not switch over to side A.)
6
Press the
06
06
06
06
06
button to record on side A, or the
1
1
1
1
1
button for
side B.
●
When you press the
06/1 0
button on the remote control, the system will
record on the side specified in step 5.
●
When the MiniDisc reaches the end, recording will stop.
To perform programmed recording:
1. Programme discs and tracks. (See page 22.)
2. Press the TAPE REC button.
3. Regardless of the tape setting (step 5), press the
2. Press the TAPE REC button.
3. Regardless of the tape setting (step 5), press the
06
button to record on side A, or
the
1
button for side B.
To interrupt recording:
Press the TAPE REC button.
To resume recording, press the same recording button you pressed in step 6. Other
buttons do not allow resuming.
To resume recording, press the same recording button you pressed in step 6. Other
buttons do not allow resuming.
To stop recording:
Press the
■
button.
The MiniDisc and tape will stop.
Auto restart function:
If the recording side is switched from side A to B during recording, the system will
record the interrupted track on side B from its beginning.
The recording will be made without cutting the beginning of the track on side B.
record the interrupted track on side B from its beginning.
The recording will be made without cutting the beginning of the track on side B.
.... To record on both sides.
.... To record on only one side.
.... To record on only one side.
T
ape Recording
43
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Recording to a Cassette Tape from the Radio
1
Tune in to the desired station. (See page 25.)
2
Load a cassette into the compartment with side A facing you.
3
Press the REV. MODE button on the remote control to choose one
side or both sides.
side or both sides.
4
Press the TAPE REC button repeatedly to switch to the side you
record on.
record on.
●
Recording will be paused.
●
To record on both sides, begin on side A. (If recording is started from side B,
the tape will not switch over to side A.)
the tape will not switch over to side A.)
5
Press the
06
06
06
06
06
button to record on side A, or the
1
1
1
1
1
button for
side B.
●
When you press the
06/1 0
button on the remote control, the system will
record on the side specified in step 4.
To interrupt recording:
Press the TAPE REC button.
To resume recording, press the same recording button you pressed in step 5. Other
buttons do not allow resuming.
To resume recording, press the same recording button you pressed in step 5. Other
buttons do not allow resuming.
To stop recording:
Press the
■
button.
Note:
If you hear a whistling noise whilst recording an AM station, move the AM loop aerial.
■
Erasing recorded tapes
1. Press the TAPE button.
2. Follow steps 2 - 5 in “Recording to a Cassette Tape from the Radio”.
2. Follow steps 2 - 5 in “Recording to a Cassette Tape from the Radio”.
.... To record on both sides.
.... To record on only one side.
.... To record on only one side.
T
ape Recording
44
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
MD Editing
Titling a MiniDisc
■
Creating disc and track names
You can give a name to discs and tracks.
One disc name and up to 255 track names can be created per disc (A maximum of 40
characters for the disc and each track name and a total of 1,700 characters can be
entered).
One disc name and up to 255 track names can be created per disc (A maximum of 40
characters for the disc and each track name and a total of 1,700 characters can be
entered).
●
Playback-only MiniDiscs cannot be edited.
1
Press the MD button and load a MiniDisc. (See page 36.)
2
Disc name
Track name
3
Within 10 seconds, press the ENTER button.
Cursor
●
The unit will enter the character input mode.
●
To cancel the operation, press the
■
button.
4
Press the DISP/CHARACTER button repeatedly to select the type
of characters.
of characters.
Capital letters
Numbers/Symbols
●
Each time the button is pressed, the letter type changes.
5
Select a character to enter using the jog dial.
6
Press the ENTER button to enter it.
Position where the next letter will be entered
7
To enter more letters, repeat steps 4 - 6.
●
To enter the same character continuously, skip step 4.
8
When the name has been completely entered, press the NAME/
TOC EDIT button.
TOC EDIT button.
Whilst in the stop mode of
MiniDisc, press the NAME/TOC
EDIT button, and then select
“DISC NAME” using the jog
dial.
MiniDisc, press the NAME/TOC
EDIT button, and then select
“DISC NAME” using the jog
dial.
During playback or in the
pause mode of MiniDisc, press
the NAME/TOC EDIT button to
select “TRACK NAME” using
the jog dial.
pause mode of MiniDisc, press
the NAME/TOC EDIT button to
select “TRACK NAME” using
the jog dial.
Click on the first or last page to see other CD-MD3000 (serv.man2) service manuals if exist.