Sharp CD-MD3000 (serv.man2) User Manual / Operation Manual ▷ View online
29
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
RDS Radio
■
Using the Auto Station Programme Memory
(ASPM)
(ASPM)
Whilst in the ASPM operation mode, the tuner will automatically search for new RDS
stations. Up to 40 stations can be stored.
If you have already stored some stations in memory, the number of new stations you
can store will be less.
stations. Up to 40 stations can be stored.
If you have already stored some stations in memory, the number of new stations you
can store will be less.
1
Press the TUNER (BAND) button to select FM band.
2
Press and hold down the ASPM button for at least 3 seconds.
1. After “ASPM” has flashed for about 4 seconds, scanning will start (87.50 - 108.00
MHz).
2. When an RDS station is found, “RDS” will appear for a short time and the sta-
tion will be stored in memory.
3. After scanning, the number of stations stored in memory will be displayed for 4
seconds, and then “END” will appear for 4 seconds.
To stop the ASPM operation before it is complete:
Press the ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept there.
The stations which are already stored in memory will be kept there.
Notes:
●
If the same station is broadcasting on different frequencies, the strongest frequency
will be stored in memory.
will be stored in memory.
●
Any station which has the same frequency as the one stored in memory will not be
stored.
stored.
●
If 40 stations have already been stored in memory, the scan will be aborted.
If you want to redo the ASPM operation, erase the preset memory.
If you want to redo the ASPM operation, erase the preset memory.
●
If the RDS signals are very weak, station names may not be stored in memory.
To erase all of the contents of preset memory:
1. Press the TUNER (BAND) button.
2. Press the ENTER button.
3. Press the CLEAR button on the remote control.
4. Whilst “ALL CLEAR” is displayed, press the ENTER button.
2. Press the ENTER button.
3. Press the CLEAR button on the remote control.
4. Whilst “ALL CLEAR” is displayed, press the ENTER button.
To store a station name again if the wrong name was stored in memory:
It may be impossible to store station names in memory using the ASPM function if
there is lots of noise or if the signal is too weak.
In this case, perform as follows.
there is lots of noise or if the signal is too weak.
In this case, perform as follows.
1. Press the PRESET (
X
or
W
) button to check whether the names are correct.
2. If you find a wrong name during receiving the station. Wait until the correct name
will be displayed. And then press the ENTER button.
3. Within 5 seconds, press the ENTER button again whilst the preset channel number
is flashing.
●
The new station name has been stored in memory correctly.
Notes:
●
The same station name can be stored in different channels.
●
In a certain area or during certain time periods, the station names may temporarily
be different.
be different.
30
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
RDS Radio
■
To recall stations in memory
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news, sports, traffic
programme, etc. ... see page 28) from the stations in memory.
programme, etc. ... see page 28) from the stations in memory.
1
Press the TUNER (BAND) button to select the FM.
2
Press the PTY.TI button.
●
“PTY TI” and “SELECT” will appear alternately for about 6 seconds.
3
Within 6 seconds, press the PRESET (
X
X
X
X
X
or
W
W
W
W
W
) button to select
the programme type.
●
Each time the button is pressed, the programme type will appear. If the but-
ton is held down for more than 0.5 seconds, the programme type will appear
continuously.
ton is held down for more than 0.5 seconds, the programme type will appear
continuously.
4
Whilst the selected programme type is flashing (within 4 sec-
onds), press the PTY.TI button again.
onds), press the PTY.TI button again.
●
After the selected programme type has been lit for 2 seconds, “SEARCH”
will appear, and the search operation will start.
will appear, and the search operation will start.
Notes:
●
If the display has stopped flashing, start again from step 2.
If the unit finds out a desired programme type, corresponding channel number will
flash for about 3 seconds, and then the station name will flash for 7 seconds, and
then will remain lit.
If the unit finds out a desired programme type, corresponding channel number will
flash for about 3 seconds, and then the station name will flash for 7 seconds, and
then will remain lit.
●
If you want to listen to the same programmed type of another station, press the
PTY.TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
PTY.TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
●
If no station can be found, “NOT FOUND” will appear for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 4, “TP” will appear. (This does not mean
that you can listen to the traffic information at that time.)
When a traffic information is broadcast, “TA” will appear.
that you can listen to the traffic information at that time.)
When a traffic information is broadcast, “TA” will appear.
To specify station names and select stations manually:
You can select a station by specifying the name (BBC R1, BBC R2, etc.) from the
stations stored in memory.
Before starting this operation, you must store one or more station names in memory.
1. Press the TUNER (BAND) button to select the FM band.
2. Press the PRESET (
stations stored in memory.
Before starting this operation, you must store one or more station names in memory.
1. Press the TUNER (BAND) button to select the FM band.
2. Press the PRESET (
X
or
W
) button to select a desired station.
3. The station name will be displayed for 3 seconds. Then the display will change as
follows.
Using the Radio Data System (RDS) (continued)
31
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
RDS Radio
■
To automatically play the desired programme
(EON-PTY)
(EON-PTY)
When the desired type of programme is broadcast, the radio switches to it automatically.
1
Tune in to an RDS station (when a station name is displayed).
2
Press the EON button when “EON” appears.
●
“PTY TI” and “SELECT” will appear alternately for about 6 seconds.
●
If the EON button is pressed when “EON” is not displayed, “NO EON” will appear
for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.
for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.
3
Whilst they are displayed, select the desired programme type by
pressing the PRESET (
pressing the PRESET (
X
X
X
X
X
or
W
W
W
W
W
) button.
●
The selected programme type will flash.
4
Within 4 seconds, press the PTY.TI button.
●
The selected programme type and “WAITING” will be displayed for 2 sec-
onds each.
onds each.
●
“PTY” will appear, and the unit will enter the EON-PTY stand-by mode.
5
When the specified programme starts on an ON (other network)
station, the unit will automatically switch to the station and “PTY”
will flash.
station, the unit will automatically switch to the station and “PTY”
will flash.
6
When the programme is over, the unit will automatically return
to the original station.
to the original station.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
(“Programme type”
(“Programme type”
→
“WAITING”)
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button. Within 4 seconds, press it
again.
(“PTY” will go out.)
again.
(“PTY” will go out.)
About the PTYI (Dynamic PTY Indicator):
“PTYI” (Dynamic PTY Indicator) will appear whilst the Dynamic PTY station is received.
Dynamic PTY indicates that the PTY for the station tuned in, or the PTY referenced in
the EON data, is assessed whenever the programme changes and may be changed.
Dynamic PTY indicates that the PTY for the station tuned in, or the PTY referenced in
the EON data, is assessed whenever the programme changes and may be changed.
PTYI
Lights up
Goes out
Lights up
Goes out
Meaning
Tuned into a dynamic PTY station.
Tuned into a static PTY.
Tuned into a static PTY.
●
When “PTYI” appears, press the DISP MODE button to check the type of the
current programme.
current programme.
32
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
RDS Radio
Using the Radio Data System (RDS) (continued)
■
To automatically play the traffic information
(EON-TI)
(EON-TI)
When the traffic information is broadcast, the radio switches to it automatically.
1
Tune in to an RDS station (when a station name is displayed).
2
Press the EON button when “EON” appears.
●
“PTY TI” and “SELECT” will appear alternately for about 6 seconds.
●
If the EON button is pressed when “EON” is not displayed, “NO EON” will appear
for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.
for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.
3
Whilst they are displayed, select the TI (Traffic Information) by
pressing the PRESET (
pressing the PRESET (
X
X
X
X
X
or
W
W
W
W
W
) button.
4
Within 4 seconds, press the PTY.TI button.
●
“TI” and “WAITING” will appear for 2 seconds each.
●
“TI” will appear, and the unit will enter the EON-TI stand-by mode.
5
When a TA specified starts on an ON (other network) station, the
unit will automatically switch to that station, and “TI” will flash.
unit will automatically switch to that station, and “TI” will flash.
6
When the traffic information is over, the unit will automatically
return to the original station.
return to the original station.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
(“TI”
(“TI”
→
“WAITING”)
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button. Within 4 seconds, press it
again.
again.
●
“TI” will go out.
Click on the first or last page to see other CD-MD3000 (serv.man2) service manuals if exist.