DOWNLOAD Sharp CD-BA1700 Service Manual ↓ Size: 1.2 MB | Pages: 36 in PDF or view online for FREE

 Demo mode

When the AC power lead is first connected, the unit will
enter the demonstration mode.

To cancel the demonstration mode:
When the unit is in the stand-by mode (demonstration
mode), press the X-BASS/DEMO button.

 The demonstration mode will be cancelled and the unit

will enter the low power consumption mode.

To return to the demonstration mode:
When the unit is in the stand-by mode, press the X-BASS/
DEMO button again.

Note:
When the power is on, the X-BASS/DEMO button can be
used to select the extra bass mode.

 To change the brightness of the display

Press the DIMMER button.

 The display will be made dimmer.

To return to the original brightness:
Press the DIMMER button again.

 Remote control

 When inserting or removing the batteries, push them

towards the   battery terminals.

 Installing the batteries incorrectly may cause the unit to

malfunction.

 Insert the batteries according to the direction indicated in

the battery compartment.

 Replace all old batteries with new ones at the same time.

 Do not mix old and new batteries.

 Remove the batteries if they are weak or if the unit will

not be used for long periods of time. This will prevent
potential damage due to battery leakage.

Caution:
Do not use rechargeable batteries (nickel-cadmium battery,
etc.).

 Replace the batteries if the operating distance is reduced

or if the operation becomes erratic.

 Periodically clean the transmitter LED on the remote con-

trol and the sensor on the main unit with a soft cloth.

 Exposing the sensor on the main unit to strong light may

interfere with operation. Change the lighting or the direc-
tion of the unit.

 Keep the remote control away from moisture, excessive

heat, shock, and vibrations.

(Main unit operation)

(Main unit operation)

When bright

When dark

 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar)
 Batteries are not included.

15

15

0.2 m - 6 m
(8" - 20')

In this example, the clock is set for the 24-hour (0:00) sys-
tem.

 Note that this can only be set when the unit is first

installed or it has been reset (see page 34).

 Press the TUNING/TIME (  or  ) button once to

advance the time by 1 hour. Hold it down to advance con-
tinuously.

 When the 12-hour display is selected, "AM" will change

automatically to "PM".

 Press the TUNING/TIME (  or  ) button once to

advance the time by 1 minute. Hold it down to change the
time in 5-minute intervals.

 The hour setting will not advance even if minutes

advance from "59" to "00".

 The clock starts operating from "0" second. (Seconds are

not displayed.) And then the clock display will disappear
after a few seconds.

To see the time display:
Press the CLOCK button.

 The time display will appear for about 5 seconds.

 The clock display will flash on and off at the push of the

CLOCK button when the AC power supply is restored
after a power failure occurs or after the AC power lead is
disconnected. If this happens, follow the procedure below
to change the clock time.

To change the clock time:
1

Press the CLOCK button.

2

Within 5 seconds, press the MEMORY/SET button.

3

Perform steps 6 - 9 above.

To change the time display mode:
1

Perform steps 1 - 2 in "RESETTING THE MICROCOM-
PUTER", on page 34.

2

Perform steps 1 - 9 above.

(Main unit operation)

"0:00"

The 24-hour display will appear. (0:00 -
23:59)

"AM 0:00"

The 12-hour display will appear. (AM 0:00
- PM 11:59)

"AM 

12:00"

The 12-hour display will appear. (AM
12:00 - PM 11:59)

AM 12:00

AM 0:00

0:00

 Volume

Press the VOLUME   button to increase the volume and the
VOLUME   button to decrease the volume.

 

 Extra bass (X-BASS)

When the power is first turned on, the unit will enter the
extra bass mode which emphasises the bass frequencies,
and "X-BASS" will appear. To cancel the extra bass mode,
press the X-BASS/DEMO(X-BASS) button. "X-BASS" will
disappear.

 Pre-programmed equalizer

When the EQUALIZER (EQUALIZER MODE) button is
pressed, the current mode setting will be displayed. To
change to a different mode, press the EQUALIZER
(EQUALIZER MODE) button repeatedly.

(Main unit)

(Remote control)

 

(Main unit)

(Remote control)

X-BASS indicator

0

1

2

29

30 MAXIMUM

.....

(Main unit)

(Remote control)

The sound is not modified.

Bass and treble are emphasised.

Bass and treble are slightly emphasised.

Treble is cut a little.

Treble is reduced a lot.

Vocals (midrange tones) are emphasised.

FLAT

ROCK

POPS

JAZZ

CLASSIC

VOCAL

 CD playback

 

 CDs can be placed on any open position on the disc tray.

 Be sure to place 8 cm (3") CD(s) in the middle of the disc

trays.

Caution:
Do not stack CDs in the tray. This can damage the player
and the CDs.

 The total number of tracks and the total playing time for

one disc will be displayed. At this time, the disc number
indicator is flashing.

 Playback will begin from track 1 on the disc you have

selected to play.

 After the disc finishes playing, the next disc will automati-

cally play.

 When there is no CD in one of the disc 1 - 3 positions,

that position will be skipped and the next CD will be
played.

 When the last track on the third disc has finished playing,

the unit will stop automatically.

 
To interrupt playback:
1

Press the CD   button on the remote control.

 " " will appear.
2

Press the     button to resume playback from the same
point.

To stop playback:
Press 

the  

(CD ) 

button.

To remove the CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.

 The disc tray will open. Remove the two discs. Then,

press the DISC SKIP button to rotate the disc tray and
remove the remaining disc.

After use:
Press the ON/STAND-BY button to enter the stand-by
mode.

12 cm (5")

8 cm (3")