Sharp CD-BA1700 User Manual / Operation Manual ▷ View online
33
USING EXTERNAL UNITS
Video/Auxiliary (Audio signal) input
To listen to or record signals from external sources
through this unit:
through this unit:
1
Use a separately available RCA lead to connect the
desired external unit to the VIDEO/AUX sockets. (red
desired external unit to the VIDEO/AUX sockets. (red
right channel, white left channel)
When using video equipment (Laser Disc player or VCR),
be sure to connect the audio output to this unit and the
video output to a television.
video output to a television.
2
Press the ON/STAND-BY button to turn the power
on.
on.
3
Press the VIDEO/AUX button.
4
Operate the external unit.
5
To record the sound from the external unit, perform
steps 2 - 5 of the "Recording from the built-in radio"
section on page 28.
steps 2 - 5 of the "Recording from the built-in radio"
section on page 28.
Note:
To prevent hum interference, do not place this unit near
television receivers.
CD digital output (optical)
The CD digital signal from this unit can be recorded by
other DAT or MiniDisc recorders.
other DAT or MiniDisc recorders.
1
Remove the CD DIGITAL OUT socket cover.
2
Use a commercially available digital cable to con-
nect the unit to the OPTICAL IN socket of a MiniDisc
recorder or a DAT.
nect the unit to the OPTICAL IN socket of a MiniDisc
recorder or a DAT.
3
Put the external unit in the recording mode.
4
Play a CD on this unit.
Note:
Only CD signals can be output.
Headphones
Before plugging in or unplugging the headphones, make
sure the volume level is reduced.
sure the volume level is reduced.
Notes:
Be sure your headphones have a 3.5 mm (1/8") diameter
plug and are between 16 ohms and 50 ohms impedance.
The recommended impedance is 32 ohms.
The recommended impedance is 32 ohms.
When headphones are connected, the speakers are dis-
abled automatically. Adjust the VOLUME buttons for the
desired volume.
desired volume.
34
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following condi-
tions:
tions:
To erase all of the stored memory contents (clock and
timer settings, and tuner and CD presets).
If the display is not correct.
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-
by mode.
by mode.
2
Whilst pressing down the / button and the X-
BASS/DEMO button, hold down the ON/STAND-BY
button for at least 1 second.
BASS/DEMO button, hold down the ON/STAND-BY
button for at least 1 second.
"CLEAR AL" will appear.
Caution:
The operation explained above will erase all data stored
in memory including clock and timer settings, and tuner
and CD presets.
and CD presets.
TRANSPORTING THE UNIT
Before you move this product to a new location, pro-
ceed as follows:
ceed as follows:
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
Remove all CDs inserted in the unit.
4
Press the OPEN/CLOSE button to close the disc
tray.
tray.
Make sure that "NO DISC" is displayed.
5
Press the ON/STAND-BY button to enter the stand-
by mode, and then unplug the AC power lead from
the AC socket.
by mode, and then unplug the AC power lead from
the AC socket.
MAINTENANCE
Internal care
Dirty heads, capstans or pinch rollers can cause poor
sound and tape jams. Clean these parts with a cotton
swab moistened with commercial head/pinch roller
cleaner or isopropyl alcohol.
swab moistened with commercial head/pinch roller
cleaner or isopropyl alcohol.
After long use, the deck's heads and capstans may
become magnetised, causing poor sound. Demagnetise
these parts once every 30 hours of playing/recording
time by using a commercial tape head demagnetiser.
Read the demagnetiser's instructions carefully before
use.
these parts once every 30 hours of playing/recording
time by using a commercial tape head demagnetiser.
Read the demagnetiser's instructions carefully before
use.
External care
Periodically wipe the cabinet with a soft cloth and a
diluted soap solution, then wipe with a dry cloth.
Do not use chemically treated cleaning cloths or other
chemicals.
X-BASS/
DEMO
DEMO
ON/
STAND-BY
STAND-BY
CD
OPEN/
CLOSE
CLOSE
ON/
STAND-BY
STAND-BY
TAPE 1
TAPE 2
35
SPECIFICATIONS
General
Amplifier section
Compact disc player section
Tuner section
Cassette deck section
Front speaker section
Surround speaker section
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
Power source:
AC 230 V, 50 Hz
Power
consumption:
consumption:
95 W
Dimensions:
Width; 270 mm (10-5/8")
Height; 330 mm (13")
Depth; 375 mm (14-6/8")
Height; 330 mm (13")
Depth; 375 mm (14-6/8")
Weight:
6.4 kg (14.0 lbs.)
Output power:
RMS; 100 W (50 W + 50 W) (10 %
T.H.D.)
T.H.D.)
RMS; 74 W (37 W + 37 W) (0.9 %
T.H.D.)
T.H.D.)
Input terminals:
Video/Auxiliary (audio signal); 500
mV/47 kohms
mV/47 kohms
Output terminals:
Front speakers; 8 ohms
Surround speakers; 16 ohms
Headphones; 16-50 ohms (recom-
mended; 32 ohms)
mended; 32 ohms)
CD digital output (optical)
Type:
3-disc multi-play compact disc
player
player
Signal readout:
Non-contact, 3-beam semi-con-
ductor laser pickup
ductor laser pickup
D/A converter:
1-bit D/A converter
Frequency
response:
response:
20 - 20,000 Hz
Dynamic range:
90 dB (1 kHz)
Frequency range:
FM; 87.5 - 108 MHz
AM; 522 - 1,620 kHz
Frequency
response:
response:
50 - 14,000 Hz (Normal tape)
Motor:
DC motor with electronic governor
1
Bias and erasure
system:
system:
AC
Tape speed:
4.76 cm/sec. (1-7/8 ips.)
Signal/noise ratio:
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/play-
back)
50 dB (TAPE 2, recording/play-
back)
Wow and flutter:
0.3 % (WRMS)
Heads:
TAPE-1: Playback 1
TAPE-2: Recording/playback 1
TAPE-2: Recording/playback 1
Erase 1
Type:
3-way [10 cm (4") woofer 2 and
5 cm (2") tweeter]
5 cm (2") tweeter]
Maximum input
power:
power:
80 W
Rated input power:
40 W
Impedance:
8 ohms
Dimensions:
Width; 220 mm (8-11/16")
Height; 330 mm (13")
Depth; 227 mm (8-15/16")
Height; 330 mm (13")
Depth; 227 mm (8-15/16")
Weight:
3.0 kg (6.6 lbs.)/each
Type:
10 cm (4") full-range speaker
Maximum input
power:
power:
30 W
Rated input power:
15 W
Impedance:
16 ohms
Dimensions:
Width; 170 mm (6-3/4")
Height; 170 mm (6-3/4")
Depth; 88 mm (3-1/2")
Height; 170 mm (6-3/4")
Depth; 88 mm (3-1/2")
Weight:
0.5 kg (1.0 lbs.)/each
TERMS OF GUARANTEE
Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replace-
ment, of this product subject to the conditions listed below:-
ment, of this product subject to the conditions listed below:-
1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does
not cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering with
the product, or repair other than by a Service Facility appointed by Sharp.
the product, or repair other than by a Service Facility appointed by Sharp.
2. As this product is intended for private domestic use only, the guarantee will not apply if the product
is used in the course of a business, trade or profession.
3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointed
Service Facility within one year from the date this product was purchased. Proof of purchase must
be provided.
be provided.
4. The guarantee does not cover carriage costs, jewelled styli, audio tapes, compact discs or batter-
ies.
5. In the unlikely event of this product requiring repair, please contact the supplier from whom it was
purchased. Where this is not possible, please contact the Sharp Customer Information Centre on
the telephone number given below.
the telephone number given below.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to your statutory rights, and does not affect these
rights in any way.
If you have any difficulty operating this product, or would like information on other Sharp products,
please telephone the Sharp Customer Information Centre on the number given below.
please telephone the Sharp Customer Information Centre on the number given below.
Sharp Customer Information Centre - Telephone 0990 274277
0003
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE
SHARP CORPORATION
9906
TINSE0312AWZZ
A0003.HK
